On Tue, Apr 27, 2021 at 11:12:56AM +0200, Tobias Waldekranz wrote:

On Mon, Apr 26, 2021 at 23:28, Vladimir Oltean [off-list ref] wrote:

quoted

On Mon, Apr 26, 2021 at 10:05:52PM +0200, Tobias Waldekranz wrote:

quoted

On Mon, Apr 26, 2021 at 22:40, Vladimir Oltean [off-list ref] wrote:

quoted

Hi Tobias,

On Mon, Apr 26, 2021 at 07:04:07PM +0200, Tobias Waldekranz wrote:

quoted

In some scenarios a tagger must know which VLAN to assign to a packet,
even if the packet is set to egress untagged. Since the VLAN
information in the skb will be removed by the bridge in this case,
track each port's PVID such that the VID of an outgoing frame can
always be determined.

Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
---

Let me give you this real-life example:

#!/bin/bash

ip link add br0 type bridge vlan_filtering 1
for eth in eth0 eth1 swp2 swp3 swp4 swp5; do
	ip link set $eth up
	ip link set $eth master br0
done
ip link set br0 up

bridge vlan add dev eth0 vid 100 pvid untagged
bridge vlan del dev swp2 vid 1
bridge vlan del dev swp3 vid 1
bridge vlan add dev swp2 vid 100
bridge vlan add dev swp3 vid 100 untagged

reproducible on the NXP LS1021A-TSN board.
The bridge receives an untagged packet on eth0 and floods it.
It should reach swp2 and swp3, and be tagged on swp2, and untagged on
swp3 respectively.

With your idea of sending untagged frames towards the port's pvid,
wouldn't we be leaking this packet to VLAN 1, therefore towards ports
swp4 and swp5, and the real destination ports would not get this packet?

I am not sure I follow. The bridge would never send the packet to
swp{4,5} because should_deliver() rejects them (as usual). So it could
only be sent either to swp2 or swp3. In the case that swp3 is first in
the bridge's port list, it would be sent untagged, but the PVID would be
100 and the flooding would thus be limited to swp{2,3}.

Sorry, _I_ don't understand.

When you say that the PVID is 100, whose PVID is it, exactly? Is it the
pvid of the source port (aka eth0 in this example)? That's not what I
see, I see the pvid of the egress port (the Marvell device)...

I meant the PVID of swp3.

In summary: This series incorrectly assumes that a port's PVID always
corresponds to the VID that should be assigned to untagged packets on
egress. This is wrong because PVID only specifies which VID to assign
packets to on ingress, it says nothing about policy on egress. Multiple
VIDs can also be configured to egress untagged on a given port. The VID
must thus be sent along with each packet in order for the driver to be
able to assign it to the correct VID.

quoted

So to reiterate: when you transmit a packet towards your hardware switch
which has br0 inside the sb_dev, how does the switch know in which VLAN
to forward that packet? As far as I am aware, when the bridge had
received the packet as untagged on eth0, it did not insert VLAN 100 into
the skb itself, so the bridge VLAN information is lost when delivering
the frame to the egress net device. Am I wrong?

VID 100 is inserted into skb->vlan_tci on ingress from eth0, in
br_vlan.c/__allowed_ingress. It is then cleared again in
br_vlan.c/br_handle_vlan if the egress port (swp3 in our example) is set
to egress the VID untagged.

The last step only clears skb->vlan_present though, the actual VID
information still resides in skb->vlan_tci. I tried just removing 5/9
from this series, and then sourced the VID from skb->vlan_tci for
untagged packets. It works like a charm! I think this is the way
forward.

The question is if we need another bit of information to signal that
skb->vlan_tci contains valid information, but the packet should still be
considered untagged? This could also be used on Rx to carry priority
(PCP) information to the bridge.

My expectation is that when you do this forwarding offload thing, the
bridge passes the classified VLAN down to the port driver, encoded
inside the accel_priv alongside the sb_dev somehow.