[PATCH net-next v3 3/3] net: phy: broadcom: Do not modify LED configuration for SFP module PHYs
From: Robert Hancock <hidden>
Date: 2021-02-16 21:19:58
Subsystem:
broadcom ethernet phy drivers, ethernet phy library, networking drivers, the rest · Maintainers:
Florian Fainelli, Andrew Lunn, Heiner Kallweit, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
bcm54xx_config_init was modifying the PHY LED configuration to enable link and activity indications. However, some SFP modules (such as Bel-Fuse SFP-1GBT-06) have no LEDs but use the LED outputs to control the SFP LOS signal, and modifying the LED settings will cause the LOS output to malfunction. Skip this configuration for PHYs which are bound to an SFP bus. Signed-off-by: Robert Hancock <redacted> --- drivers/net/phy/broadcom.c | 24 +++++++++++++++--------- 1 file changed, 15 insertions(+), 9 deletions(-)
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 8e7fc3368380..fa0be591ae79 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c@@ -366,18 +366,24 @@ static int bcm54xx_config_init(struct phy_device *phydev) bcm54xx_phydsp_config(phydev); - /* Encode link speed into LED1 and LED3 pair (green/amber). + /* For non-SFP setups, encode link speed into LED1 and LED3 pair + * (green/amber). * Also flash these two LEDs on activity. This means configuring * them for MULTICOLOR and encoding link/activity into them. + * Don't do this for devices on an SFP module, since some of these + * use the LED outputs to control the SFP LOS signal, and changing + * these settings will cause LOS to malfunction. */ - val = BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_MULTICOLOR1) | - BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_MULTICOLOR1); - bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1, val); - - val = BCM_LED_MULTICOLOR_IN_PHASE | - BCM5482_SHD_LEDS1_LED1(BCM_LED_MULTICOLOR_LINK_ACT) | - BCM5482_SHD_LEDS1_LED3(BCM_LED_MULTICOLOR_LINK_ACT); - bcm_phy_write_exp(phydev, BCM_EXP_MULTICOLOR, val); + if (!phy_on_sfp(phydev)) { + val = BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_MULTICOLOR1) | + BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_MULTICOLOR1); + bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1, val); + + val = BCM_LED_MULTICOLOR_IN_PHASE | + BCM5482_SHD_LEDS1_LED1(BCM_LED_MULTICOLOR_LINK_ACT) | + BCM5482_SHD_LEDS1_LED3(BCM_LED_MULTICOLOR_LINK_ACT); + bcm_phy_write_exp(phydev, BCM_EXP_MULTICOLOR, val); + } return 0; }
--
2.27.0