Thread (9 messages) 9 messages, 3 authors, 2020-12-30
STALE1979d
Revisions (4)
  1. v1 [diff vs current]
  2. v2 [diff vs current]
  3. v3 current
  4. v4 [diff vs current]

[PATCH v3 1/5] dt-bindings: net: dwmac-meson: use picoseconds for the RGMII RX delay

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date: 2020-12-23 23:31:22
Also in: linux-amlogic, linux-arm-kernel, linux-devicetree, lkml
Subsystem: networking drivers, open firmware and flattened device tree bindings, the rest · Maintainers: Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds

Amlogic Meson G12A, G12B and SM1 SoCs have a more advanced RGMII RX
delay register which allows picoseconds precision. Deprecate the old
"amlogic,rx-delay-ns" in favour of the generic "rx-internal-delay-ps"
property.

For older SoCs the only known supported values were 0ns and 2ns. The new
SoCs have support for RGMII RX delays between 0ps and 3000ps in 200ps
steps.

Don't carry over the description for the "rx-internal-delay-ps" property
and inherit that from ethernet-controller.yaml instead.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 .../bindings/net/amlogic,meson-dwmac.yaml     | 55 +++++++++++++++++--
 1 file changed, 49 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml
index 6b057b117aa0..a406e38e1848 100644
--- a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml
@@ -74,17 +74,60 @@ allOf:
             Any configuration is ignored when the phy-mode is set to "rmii".
 
         amlogic,rx-delay-ns:
+          deprecated: true
           enum:
             - 0
             - 2
           default: 0
           description:
-            The internal RGMII RX clock delay (provided by this IP block) in
-            nanoseconds. When phy-mode is set to "rgmii" then the RX delay
-            should be explicitly configured. When the phy-mode is set to
-            either "rgmii-id" or "rgmii-rxid" the RX clock delay is already
-            provided by the PHY. Any configuration is ignored when the
-            phy-mode is set to "rmii".
+            The internal RGMII RX clock delay in nanoseconds. Deprecated, use
+            rx-internal-delay-ps instead.
+
+        rx-internal-delay-ps:
+          default: 0
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - amlogic,meson8b-dwmac
+              - amlogic,meson8m2-dwmac
+              - amlogic,meson-gxbb-dwmac
+              - amlogic,meson-axg-dwmac
+    then:
+      properties:
+        rx-internal-delay-ps:
+          enum:
+            - 0
+            - 2000
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - amlogic,meson-g12a-dwmac
+    then:
+      properties:
+        rx-internal-delay-ps:
+          enum:
+            - 0
+            - 200
+            - 400
+            - 600
+            - 800
+            - 1000
+            - 1200
+            - 1400
+            - 1600
+            - 1800
+            - 2000
+            - 2200
+            - 2400
+            - 2600
+            - 2800
+            - 3000
 
 properties:
   compatible:
-- 
2.29.2
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help