What:		/sys/bus/iio/devices/iio:deviceX/in_count_enable_mode_available
 KernelVersion:	4.12
 Contact:	benjamin.gaignard@st.com

@@ -104,6 +146,7 @@ Description:
 		Configure the device counter enable modes, in all case
 		counting direction is set by in_count0_count_direction
 		attribute and the counter is clocked by the internal clock.
+
 		always:
 			Counter is always ON.
 

diff --git a/Documentation/ABI/testing/sysfs-bus-intel_th-devices-msc b/Documentation/ABI/testing/sysfs-bus-intel_th-devices-msc
index 7fd2601c2831..a74252e580a5 100644
--- a/Documentation/ABI/testing/sysfs-bus-intel_th-devices-msc
+++ b/Documentation/ABI/testing/sysfs-bus-intel_th-devices-msc

@@ -9,11 +9,13 @@ Date:		June 2015
 KernelVersion:	4.3
 Contact:	Alexander Shishkin <alexander.shishkin@linux.intel.com>
 Description:	(RW) Configure MSC operating mode:
+
 		  - "single", for contiguous buffer mode (high-order alloc);
 		  - "multi", for multiblock mode;
 		  - "ExI", for DCI handler mode;
 		  - "debug", for debug mode;
 		  - any of the currently loaded buffer sinks.
+
 		If operating mode changes, existing buffer is deallocated,
 		provided there are no active users and tracing is not enabled,
 		otherwise the write will fail.

@@ -23,10 +25,12 @@ Date:		June 2015
 KernelVersion:	4.3
 Contact:	Alexander Shishkin <alexander.shishkin@linux.intel.com>
 Description:	(RW) Configure MSC buffer size for "single" or "multi" modes.
+
 		In single mode, this is a single number of pages, has to be
 		power of 2. In multiblock mode, this is a comma-separated list
 		of numbers of pages for each window to be allocated. Number of
 		windows is not limited.
+
 		Writing to this file deallocates existing buffer (provided
 		there are no active users and tracing is not enabled) and then
 		allocates a new one.

diff --git a/Documentation/ABI/testing/sysfs-bus-nfit b/Documentation/ABI/testing/sysfs-bus-nfit
index e4f76e7eab93..63ef0b9ecce7 100644
--- a/Documentation/ABI/testing/sysfs-bus-nfit
+++ b/Documentation/ABI/testing/sysfs-bus-nfit

@@ -1,4 +1,4 @@
-For all of the nmem device attributes under nfit/*, see the 'NVDIMM Firmware
+For all of the nmem device attributes under ``nfit/*``, see the 'NVDIMM Firmware
 Interface Table (NFIT)' section in the ACPI specification
 (http://www.uefi.org/specifications) for more details.
 

diff --git a/Documentation/ABI/testing/sysfs-bus-pci-devices-aer_stats b/Documentation/ABI/testing/sysfs-bus-pci-devices-aer_stats
index 3c9a8c4a25eb..860db53037a5 100644
--- a/Documentation/ABI/testing/sysfs-bus-pci-devices-aer_stats
+++ b/Documentation/ABI/testing/sysfs-bus-pci-devices-aer_stats

@@ -1,6 +1,6 @@
-==========================
 PCIe Device AER statistics
-==========================
+--------------------------
+
 These attributes show up under all the devices that are AER capable. These
 statistical counters indicate the errors "as seen/reported by the device".
 Note that this may mean that if an endpoint is causing problems, the AER

@@ -17,19 +17,18 @@ Description:	List of correctable errors seen and reported by this
 		PCI device using ERR_COR. Note that since multiple errors may
 		be reported using a single ERR_COR message, thus
 		TOTAL_ERR_COR at the end of the file may not match the actual
-		total of all the errors in the file. Sample output:
--------------------------------------------------------------------------
-localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_correctable
-Receiver Error 2
-Bad TLP 0
-Bad DLLP 0
-RELAY_NUM Rollover 0
-Replay Timer Timeout 0
-Advisory Non-Fatal 0
-Corrected Internal Error 0
-Header Log Overflow 0
-TOTAL_ERR_COR 2
--------------------------------------------------------------------------
+		total of all the errors in the file. Sample output::
+
+		    localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_correctable
+		    Receiver Error 2
+		    Bad TLP 0
+		    Bad DLLP 0
+		    RELAY_NUM Rollover 0
+		    Replay Timer Timeout 0
+		    Advisory Non-Fatal 0
+		    Corrected Internal Error 0
+		    Header Log Overflow 0
+		    TOTAL_ERR_COR 2
 
 What:		/sys/bus/pci/devices/<dev>/aer_dev_fatal
 Date:		July 2018

@@ -39,28 +38,27 @@ Description:	List of uncorrectable fatal errors seen and reported by this
 		PCI device using ERR_FATAL. Note that since multiple errors may
 		be reported using a single ERR_FATAL message, thus
 		TOTAL_ERR_FATAL at the end of the file may not match the actual
-		total of all the errors in the file. Sample output:
--------------------------------------------------------------------------
-localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_fatal
-Undefined 0
-Data Link Protocol 0
-Surprise Down Error 0
-Poisoned TLP 0
-Flow Control Protocol 0
-Completion Timeout 0
-Completer Abort 0
-Unexpected Completion 0
-Receiver Overflow 0
-Malformed TLP 0
-ECRC 0
-Unsupported Request 0
-ACS Violation 0
-Uncorrectable Internal Error 0
-MC Blocked TLP 0
-AtomicOp Egress Blocked 0
-TLP Prefix Blocked Error 0
-TOTAL_ERR_FATAL 0
--------------------------------------------------------------------------
+		total of all the errors in the file. Sample output::
+
+		    localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_fatal
+		    Undefined 0
+		    Data Link Protocol 0
+		    Surprise Down Error 0
+		    Poisoned TLP 0
+		    Flow Control Protocol 0
+		    Completion Timeout 0
+		    Completer Abort 0
+		    Unexpected Completion 0
+		    Receiver Overflow 0
+		    Malformed TLP 0
+		    ECRC 0
+		    Unsupported Request 0
+		    ACS Violation 0
+		    Uncorrectable Internal Error 0
+		    MC Blocked TLP 0
+		    AtomicOp Egress Blocked 0
+		    TLP Prefix Blocked Error 0
+		    TOTAL_ERR_FATAL 0
 
 What:		/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
 Date:		July 2018

@@ -70,32 +68,31 @@ Description:	List of uncorrectable nonfatal errors seen and reported by this
 		PCI device using ERR_NONFATAL. Note that since multiple errors
 		may be reported using a single ERR_FATAL message, thus
 		TOTAL_ERR_NONFATAL at the end of the file may not match the
-		actual total of all the errors in the file. Sample output:
--------------------------------------------------------------------------
-localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_nonfatal
-Undefined 0
-Data Link Protocol 0
-Surprise Down Error 0
-Poisoned TLP 0
-Flow Control Protocol 0
-Completion Timeout 0
-Completer Abort 0
-Unexpected Completion 0
-Receiver Overflow 0
-Malformed TLP 0
-ECRC 0
-Unsupported Request 0
-ACS Violation 0
-Uncorrectable Internal Error 0
-MC Blocked TLP 0
-AtomicOp Egress Blocked 0
-TLP Prefix Blocked Error 0
-TOTAL_ERR_NONFATAL 0
--------------------------------------------------------------------------
+		actual total of all the errors in the file. Sample output::
+
+		    localhost /sys/devices/pci0000:00/0000:00:1c.0 # cat aer_dev_nonfatal
+		    Undefined 0
+		    Data Link Protocol 0
+		    Surprise Down Error 0
+		    Poisoned TLP 0
+		    Flow Control Protocol 0
+		    Completion Timeout 0
+		    Completer Abort 0
+		    Unexpected Completion 0
+		    Receiver Overflow 0
+		    Malformed TLP 0
+		    ECRC 0
+		    Unsupported Request 0
+		    ACS Violation 0
+		    Uncorrectable Internal Error 0
+		    MC Blocked TLP 0
+		    AtomicOp Egress Blocked 0
+		    TLP Prefix Blocked Error 0
+		    TOTAL_ERR_NONFATAL 0
 
-============================
 PCIe Rootport AER statistics
-============================
+----------------------------
+
 These attributes show up under only the rootports (or root complex event
 collectors) that are AER capable. These indicate the number of error messages as
 "reported to" the rootport. Please note that the rootports also transmit

diff --git a/Documentation/ABI/testing/sysfs-bus-rapidio b/Documentation/ABI/testing/sysfs-bus-rapidio
index 13208b27dd87..634ea207a50a 100644
--- a/Documentation/ABI/testing/sysfs-bus-rapidio
+++ b/Documentation/ABI/testing/sysfs-bus-rapidio

@@ -4,24 +4,27 @@ Description:
 		an individual subdirectory with the following name format of
 		device_name "nn:d:iiii", where:
 
-		nn   - two-digit hexadecimal ID of RapidIO network where the
+		====   ========================================================
+		nn     two-digit hexadecimal ID of RapidIO network where the
 		       device resides
-		d    - device type: 'e' - for endpoint or 's' - for switch
-		iiii - four-digit device destID for endpoints, or switchID for
+		d      device type: 'e' - for endpoint or 's' - for switch
+		iiii   four-digit device destID for endpoints, or switchID for
 		       switches
+		====   ========================================================
 
 		For example, below is a list of device directories that
 		represents a typical RapidIO network with one switch, one host,
 		and two agent endpoints, as it is seen by the enumerating host
-		(with destID = 1):
+		(with destID = 1)::
 
-		/sys/bus/rapidio/devices/00:e:0000
-		/sys/bus/rapidio/devices/00:e:0002
-		/sys/bus/rapidio/devices/00:s:0001
+		  /sys/bus/rapidio/devices/00:e:0000
+		  /sys/bus/rapidio/devices/00:e:0002
+		  /sys/bus/rapidio/devices/00:s:0001
 
-		NOTE: An enumerating or discovering endpoint does not create a
-		sysfs entry for itself, this is why an endpoint with destID=1 is
-		not shown in the list.
+		NOTE:
+		  An enumerating or discovering endpoint does not create a
+		  sysfs entry for itself, this is why an endpoint with destID=1
+		  is not shown in the list.
 
 Attributes Common for All RapidIO Devices
 -----------------------------------------

diff --git a/Documentation/ABI/testing/sysfs-bus-thunderbolt b/Documentation/ABI/testing/sysfs-bus-thunderbolt
index dd565c378b40..171127294674 100644
--- a/Documentation/ABI/testing/sysfs-bus-thunderbolt
+++ b/Documentation/ABI/testing/sysfs-bus-thunderbolt

@@ -37,16 +37,18 @@ Contact:	thunderbolt-software@lists.01.org
 Description:	This attribute holds current Thunderbolt security level
 		set by the system BIOS. Possible values are:
 
-		none: All devices are automatically authorized
-		user: Devices are only authorized based on writing
-		      appropriate value to the authorized attribute
-		secure: Require devices that support secure connect at
-			minimum. User needs to authorize each device.
-		dponly: Automatically tunnel Display port (and USB). No
-			PCIe tunnels are created.
-		usbonly: Automatically tunnel USB controller of the
+		=======  ==================================================
+		none     All devices are automatically authorized
+		user     Devices are only authorized based on writing
+		         appropriate value to the authorized attribute
+		secure   Require devices that support secure connect at
+			 minimum. User needs to authorize each device.
+		dponly   Automatically tunnel Display port (and USB). No
+			 PCIe tunnels are created.
+		usbonly  Automatically tunnel USB controller of the
 			 connected Thunderbolt dock (and Display Port). All
 			 PCIe links downstream of the dock are removed.
+		=======  ==================================================
 
 What: /sys/bus/thunderbolt/devices/.../authorized
 Date:		Sep 2017

@@ -61,17 +63,23 @@ Description:	This attribute is used to authorize Thunderbolt devices
 		yet authorized.
 
 		Possible values are supported:
-		1: The device will be authorized and connected
+
+		==  ===========================================
+		1   The device will be authorized and connected
+		==  ===========================================
 
 		When key attribute contains 32 byte hex string the possible
 		values are:
-		1: The 32 byte hex string is added to the device NVM and
-		   the device is authorized.
-		2: Send a challenge based on the 32 byte hex string. If the
-		   challenge response from device is valid, the device is
-		   authorized. In case of failure errno will be ENOKEY if
-		   the device did not contain a key at all, and
-		   EKEYREJECTED if the challenge response did not match.
+
+		==  ========================================================
+		1   The 32 byte hex string is added to the device NVM and
+		    the device is authorized.
+		2   Send a challenge based on the 32 byte hex string. If the
+		    challenge response from device is valid, the device is
+		    authorized. In case of failure errno will be ENOKEY if
+		    the device did not contain a key at all, and
+		    EKEYREJECTED if the challenge response did not match.
+		==  ========================================================
 
 What: /sys/bus/thunderbolt/devices/.../boot
 Date:		Jun 2018

diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
index 614d216dff1d..e449b8374f6a 100644
--- a/Documentation/ABI/testing/sysfs-bus-usb
+++ b/Documentation/ABI/testing/sysfs-bus-usb

@@ -72,24 +72,27 @@ Description:
 		table at compile time. The format for the device ID is:
 		idVendor idProduct bInterfaceClass RefIdVendor RefIdProduct
 		The vendor ID and device ID fields are required, the
-		rest is optional. The Ref* tuple can be used to tell the
+		rest is optional. The `Ref*` tuple can be used to tell the
 		driver to use the same driver_data for the new device as
 		it is used for the reference device.
 		Upon successfully adding an ID, the driver will probe
-		for the device and attempt to bind to it.  For example:
-		# echo "8086 10f5" > /sys/bus/usb/drivers/foo/new_id
+		for the device and attempt to bind to it.  For example::
+
+		  # echo "8086 10f5" > /sys/bus/usb/drivers/foo/new_id
 
 		Here add a new device (0458:7045) using driver_data from
-		an already supported device (0458:704c):
-		# echo "0458 7045 0 0458 704c" > /sys/bus/usb/drivers/foo/new_id
+		an already supported device (0458:704c)::
+
+		  # echo "0458 7045 0 0458 704c" > /sys/bus/usb/drivers/foo/new_id
 
 		Reading from this file will list all dynamically added
 		device IDs in the same format, with one entry per
-		line. For example:
-		# cat /sys/bus/usb/drivers/foo/new_id
-		8086 10f5
-		dead beef 06
-		f00d cafe
+		line. For example::
+
+		  # cat /sys/bus/usb/drivers/foo/new_id
+		  8086 10f5
+		  dead beef 06
+		  f00d cafe
 
 		The list will be truncated at PAGE_SIZE bytes due to
 		sysfs restrictions.

@@ -209,6 +212,7 @@ Description:
 		advance, and behaves well according to the specification.
 		This attribute is a bit-field that controls the behavior of
 		a specific port:
+
 		 - Bit 0 of this field selects the "old" enumeration scheme,
 		   as it is considerably faster (it only causes one USB reset
 		   instead of 2).

@@ -233,10 +237,10 @@ Description:
 		poll() for monitoring changes to this value in user space.
 
 		Any time this value changes the corresponding hub device will send a
-		udev event with the following attributes:
+		udev event with the following attributes::
 
-		OVER_CURRENT_PORT=/sys/bus/usb/devices/.../(hub interface)/portX
-		OVER_CURRENT_COUNT=[current value of this sysfs attribute]
+		  OVER_CURRENT_PORT=/sys/bus/usb/devices/.../(hub interface)/portX
+		  OVER_CURRENT_COUNT=[current value of this sysfs attribute]
 
 What:		/sys/bus/usb/devices/.../(hub interface)/portX/usb3_lpm_permit
 Date:		November 2015

diff --git a/Documentation/ABI/testing/sysfs-bus-usb-devices-usbsevseg b/Documentation/ABI/testing/sysfs-bus-usb-devices-usbsevseg
index 9ade80f81f96..2f86e4223bfc 100644
--- a/Documentation/ABI/testing/sysfs-bus-usb-devices-usbsevseg
+++ b/Documentation/ABI/testing/sysfs-bus-usb-devices-usbsevseg

@@ -12,8 +12,11 @@ KernelVersion:	2.6.26
 Contact:	Harrison Metzger <harrisonmetz@gmail.com>
 Description:	Controls the devices display mode.
 		For a 6 character display the values are
+
 			MSB 0x06; LSB 0x3F, and
+
 		for an 8 character display the values are
+
 			MSB 0x08; LSB 0xFF.
 
 What:		/sys/bus/usb/.../textmode

@@ -37,7 +40,7 @@ KernelVersion:	2.6.26
 Contact:	Harrison Metzger <harrisonmetz@gmail.com>
 Description:	Controls the decimal places on the device.
 		To set the nth decimal place, give this field
-		the value of 10 ** n. Assume this field has
+		the value of ``10 ** n``. Assume this field has
 		the value k and has 1 or more decimal places set,
 		to set the mth place (where m is not already set),
-		change this fields value to k + 10 ** m.
+		change this fields value to ``k + 10 ** m``.

diff --git a/Documentation/ABI/testing/sysfs-bus-vfio-mdev b/Documentation/ABI/testing/sysfs-bus-vfio-mdev
index 452dbe39270e..59fc804265db 100644
--- a/Documentation/ABI/testing/sysfs-bus-vfio-mdev
+++ b/Documentation/ABI/testing/sysfs-bus-vfio-mdev

@@ -28,8 +28,9 @@ Description:
 		Writing UUID to this file will create mediated device of
 		type <type-id> for parent device <device>. This is a
 		write-only file.
-		For example:
-		# echo "83b8f4f2-509f-382f-3c1e-e6bfe0fa1001" >	\
+		For example::
+
+		  # echo "83b8f4f2-509f-382f-3c1e-e6bfe0fa1001" >	\
 		       /sys/devices/foo/mdev_supported_types/foo-1/create
 
 What:           /sys/.../mdev_supported_types/<type-id>/devices/

@@ -107,5 +108,6 @@ Description:
 		Writing '1' to this file destroys the mediated device. The
 		vendor driver can fail the remove() callback if that device
 		is active and the vendor driver doesn't support hot unplug.
-		Example:
-		# echo 1 > /sys/bus/mdev/devices/<UUID>/remove
+		Example::
+
+		  # echo 1 > /sys/bus/mdev/devices/<UUID>/remove

diff --git a/Documentation/ABI/testing/sysfs-class-cxl b/Documentation/ABI/testing/sysfs-class-cxl
index 7970e3713e70..a6f51a104c44 100644
--- a/Documentation/ABI/testing/sysfs-class-cxl
+++ b/Documentation/ABI/testing/sysfs-class-cxl

@@ -72,11 +72,16 @@ Description:    read/write
                 when performing the START_WORK ioctl. Only applicable when
                 running under hashed page table mmu.
                 Possible values:
-                        none: No prefaulting (default)
-                        work_element_descriptor: Treat the work element
-                                 descriptor as an effective address and
-                                 prefault what it points to.
-                        all: all segments process calling START_WORK maps.
+
+                =======================  ======================================
+		none			 No prefaulting (default)
+		work_element_descriptor  Treat the work element
+					 descriptor as an effective address and
+					 prefault what it points to.
+                all			 all segments process calling
+					 START_WORK maps.
+                =======================  ======================================
+
 Users:		https://github.com/ibm-capi/libcxl
 
 What:           /sys/class/cxl/<afu>/reset

diff --git a/Documentation/ABI/testing/sysfs-class-led b/Documentation/ABI/testing/sysfs-class-led
index 5f67f7ab277b..65e040978f73 100644
--- a/Documentation/ABI/testing/sysfs-class-led
+++ b/Documentation/ABI/testing/sysfs-class-led

@@ -50,7 +50,7 @@ Description:
 		You can change triggers in a similar manner to the way an IO
 		scheduler is chosen. Trigger specific parameters can appear in
 		/sys/class/leds/<led> once a given trigger is selected. For
-		their documentation see sysfs-class-led-trigger-*.
+		their documentation see `sysfs-class-led-trigger-*`.
 
 What:		/sys/class/leds/<led>/inverted
 Date:		January 2011

diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-el15203000 b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000
index f520ece9b64c..69befe947d7e 100644
--- a/Documentation/ABI/testing/sysfs-class-led-driver-el15203000
+++ b/Documentation/ABI/testing/sysfs-class-led-driver-el15203000

@@ -6,127 +6,132 @@ Description:
 		The LEDs board supports only predefined patterns by firmware
 		for specific LEDs.
 
-		Breathing mode for Screen frame light tube:
-		"0 4000 1 4000"
+		Breathing mode for Screen frame light tube::
 
-		    ^
-		    |
-		Max-|     ---
-		    |    /   \
-		    |   /     \
-		    |  /       \     /
-		    | /         \   /
-		Min-|-           ---
-		    |
-		    0------4------8--> time (sec)
+		    "0 4000 1 4000"
 
-		Cascade mode for Pipe LED:
-		"1 800 2 800 4 800 8 800 16 800"
+			^
+			|
+		    Max-|     ---
+			|    /   \
+			|   /     \
+			|  /       \     /
+			| /         \   /
+		    Min-|-           ---
+			|
+			0------4------8--> time (sec)
 
-		      ^
-		      |
-		0 On -|----+                   +----+                   +---
-		      |    |                   |    |                   |
-		  Off-|    +-------------------+    +-------------------+
-		      |
-		1 On -|    +----+                   +----+
-		      |    |    |                   |    |
-		  Off |----+    +-------------------+    +------------------
-		      |
-		2 On -|         +----+                   +----+
-		      |         |    |                   |    |
-		  Off-|---------+    +-------------------+    +-------------
-		      |
-		3 On -|              +----+                   +----+
-		      |              |    |                   |    |
-		  Off-|--------------+    +-------------------+    +--------
-		      |
-		4 On -|                   +----+                   +----+
-		      |                   |    |                   |    |
-		  Off-|-------------------+    +-------------------+    +---
-		      |
-		      0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
+		Cascade mode for Pipe LED::
 
-		Inverted cascade mode for Pipe LED:
-		"30 800 29 800 27 800 23 800 15 800"
+		    "1 800 2 800 4 800 8 800 16 800"
 
-		      ^
-		      |
-		0 On -|    +-------------------+    +-------------------+
-		      |    |                   |    |                   |
-		  Off-|----+                   +----+                   +---
-		      |
-		1 On -|----+    +-------------------+    +------------------
-		      |    |    |                   |    |
-		  Off |    +----+                   +----+
-		      |
-		2 On -|---------+    +-------------------+    +-------------
-		      |         |    |                   |    |
-		  Off-|         +----+                   +----+
-		      |
-		3 On -|--------------+    +-------------------+    +--------
-		      |              |    |                   |    |
-		  Off-|              +----+                   +----+
-		      |
-		4 On -|-------------------+    +-------------------+    +---
-		      |                   |    |                   |    |
-		  Off-|                   +----+                   +----+
-		      |
-		      0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
+			^
+			|
+		    0 On -|----+                   +----+                   +---
+			|    |                   |    |                   |
+		    Off-|    +-------------------+    +-------------------+
+			|
+		    1 On -|    +----+                   +----+
+			|    |    |                   |    |
+		    Off |----+    +-------------------+    +------------------
+			|
+		    2 On -|         +----+                   +----+
+			|         |    |                   |    |
+		    Off-|---------+    +-------------------+    +-------------
+			|
+		    3 On -|              +----+                   +----+
+			|              |    |                   |    |
+		    Off-|--------------+    +-------------------+    +--------
+			|
+		    4 On -|                   +----+                   +----+
+			|                   |    |                   |    |
+		    Off-|-------------------+    +-------------------+    +---
+			|
+			0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
 
-		Bounce mode for Pipe LED:
-		"1 800 2 800 4 800 8 800 16 800 16 800 8 800 4 800 2 800 1 800"
+		Inverted cascade mode for Pipe LED::
 
-		      ^
-		      |
-		0 On -|----+                                       +--------
-		      |    |                                       |
-		  Off-|    +---------------------------------------+
-		      |
-		1 On -|    +----+                             +----+
-		      |    |    |                             |    |
-		  Off |----+    +-----------------------------+    +--------
-		      |
-		2 On -|         +----+                   +----+
-		      |         |    |                   |    |
-		  Off-|---------+    +-------------------+    +-------------
-		      |
-		3 On -|              +----+         +----+
-		      |              |    |         |    |
-		  Off-|--------------+    +---------+    +------------------
-		      |
-		4 On -|                   +---------+
-		      |                   |         |
-		  Off-|-------------------+         +-----------------------
-		      |
-		      0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
+		    "30 800 29 800 27 800 23 800 15 800"
 
-		Inverted bounce mode for Pipe LED:
-		"30 800 29 800 27 800 23 800 15 800 15 800 23 800 27 800 29 800 30 800"
+			^
+			|
+		    0 On -|    +-------------------+    +-------------------+
+			|    |                   |    |                   |
+		    Off-|----+                   +----+                   +---
+			|
+		    1 On -|----+    +-------------------+    +------------------
+			|    |    |                   |    |
+		    Off |    +----+                   +----+
+			|
+		    2 On -|---------+    +-------------------+    +-------------
+			|         |    |                   |    |
+		    Off-|         +----+                   +----+
+			|
+		    3 On -|--------------+    +-------------------+    +--------
+			|              |    |                   |    |
+		    Off-|              +----+                   +----+
+			|
+		    4 On -|-------------------+    +-------------------+    +---
+			|                   |    |                   |    |
+		    Off-|                   +----+                   +----+
+			|
+			0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
 
-		      ^
-		      |
-		0 On -|    +---------------------------------------+
-		      |    |                                       |
-		  Off-|----+                                       +--------
-		      |
-		1 On -|----+    +-----------------------------+    +--------
-		      |    |    |                             |    |
-		  Off |    +----+                             +----+
-		      |
-		2 On -|---------+    +-------------------+    +-------------
-		      |         |    |                   |    |
-		  Off-|         +----+                   +----+
-		      |
-		3 On -|--------------+    +---------+    +------------------
-		      |              |    |         |    |
-		  Off-|              +----+         +----+
-		      |
-		4 On -|-------------------+         +-----------------------
-		      |                   |         |
-		  Off-|                   +---------+
-		      |
-		      0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
+		Bounce mode for Pipe LED::
+
+		    "1 800 2 800 4 800 8 800 16 800 16 800 8 800 4 800 2 800 1 800"
+
+			^
+			|
+		    0 On -|----+                                       +--------
+			|    |                                       |
+		    Off-|    +---------------------------------------+
+			|
+		    1 On -|    +----+                             +----+
+			|    |    |                             |    |
+		    Off |----+    +-----------------------------+    +--------
+			|
+		    2 On -|         +----+                   +----+
+			|         |    |                   |    |
+		    Off-|---------+    +-------------------+    +-------------
+			|
+		    3 On -|              +----+         +----+
+			|              |    |         |    |
+		    Off-|--------------+    +---------+    +------------------
+			|
+		    4 On -|                   +---------+
+			|                   |         |
+		    Off-|-------------------+         +-----------------------
+			|
+			0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
+
+		Inverted bounce mode for Pipe LED::
+
+		    "30 800 29 800 27 800 23 800 15 800 15 800 23 800 27 800 29 800 30 800"
+
+			^
+			|
+		    0 On -|    +---------------------------------------+
+			|    |                                       |
+		    Off-|----+                                       +--------
+			|
+		    1 On -|----+    +-----------------------------+    +--------
+			|    |    |                             |    |
+		    Off |    +----+                             +----+
+			|
+		    2 On -|---------+    +-------------------+    +-------------
+			|         |    |                   |    |
+		    Off-|         +----+                   +----+
+			|
+		    3 On -|--------------+    +---------+    +------------------
+			|              |    |         |    |
+		    Off-|              +----+         +----+
+			|
+		    4 On -|-------------------+         +-----------------------
+			|                   |         |
+		    Off-|                   +---------+
+			|
+			0---0.8--1.6--2.4--3.2---4---4.8--5.6--6.4--7.2---8--> time (sec)
 
 What:		/sys/class/leds/<led>/repeat
 Date:		September 2019

diff --git a/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx b/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
index 45b1e605d355..215482379580 100644
--- a/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx
+++ b/Documentation/ABI/testing/sysfs-class-led-driver-sc27xx

@@ -12,8 +12,8 @@ Description:
 		format, we should set brightness as 0 for rise stage, fall
 		stage and low stage.
 
-		Min stage duration: 125 ms
-		Max stage duration: 31875 ms
+		- Min stage duration: 125 ms
+		- Max stage duration: 31875 ms
 
 		Since the stage duration step is 125 ms, the duration should be
 		a multiplier of 125, like 125ms, 250ms, 375ms, 500ms ... 31875ms.

diff --git a/Documentation/ABI/testing/sysfs-class-mic b/Documentation/ABI/testing/sysfs-class-mic
index 6ef682603179..bd0e780c3760 100644
--- a/Documentation/ABI/testing/sysfs-class-mic
+++ b/Documentation/ABI/testing/sysfs-class-mic

@@ -41,24 +41,33 @@ Description:
 		When read, this entry provides the current state of an Intel
 		MIC device in the context of the card OS. Possible values that
 		will be read are:
-		"ready" - The MIC device is ready to boot the card OS. On
-		reading this entry after an OSPM resume, a "boot" has to be
-		written to this entry if the card was previously shutdown
-		during OSPM suspend.
-		"booting" - The MIC device has initiated booting a card OS.
-		"online" - The MIC device has completed boot and is online
-		"shutting_down" - The card OS is shutting down.
-		"resetting" - A reset has been initiated for the MIC device
-		"reset_failed" - The MIC device has failed to reset.
+
+
+		===============  ===============================================
+		"ready"		 The MIC device is ready to boot the card OS.
+				 On reading this entry after an OSPM resume,
+				 a "boot" has to be written to this entry if
+				 the card was previously shutdown during OSPM
+				 suspend.
+		"booting"	 The MIC device has initiated booting a card OS.
+		"online"	 The MIC device has completed boot and is online
+		"shutting_down"	 The card OS is shutting down.
+		"resetting"	 A reset has been initiated for the MIC device
+		"reset_failed"	 The MIC device has failed to reset.
+		===============  ===============================================
 
 		When written, this sysfs entry triggers different state change
 		operations depending upon the current state of the card OS.
 		Acceptable values are:
-		"boot" - Boot the card OS image specified by the combination
-			 of firmware, ramdisk, cmdline and bootmode
-			sysfs entries.
-		"reset" - Initiates device reset.
-		"shutdown" - Initiates card OS shutdown.
+
+
+		==========  ===================================================
+		"boot"      Boot the card OS image specified by the combination
+			    of firmware, ramdisk, cmdline and bootmode
+			    sysfs entries.
+		"reset"     Initiates device reset.
+		"shutdown"  Initiates card OS shutdown.
+		==========  ===================================================
 
 What:		/sys/class/mic/mic(x)/shutdown_status
 Date:		October 2013

@@ -69,12 +78,15 @@ Description:
 		OS can shutdown because of various reasons. When read, this
 		entry provides the status on why the card OS was shutdown.
 		Possible values are:
-		"nop" -  shutdown status is not applicable, when the card OS is
-			"online"
-		"crashed" - Shutdown because of a HW or SW crash.
-		"halted" - Shutdown because of a halt command.
-		"poweroff" - Shutdown because of a poweroff command.
-		"restart" - Shutdown because of a restart command.
+
+		==========  ===================================================
+		"nop"       shutdown status is not applicable, when the card OS
+			    is "online"
+		"crashed"   Shutdown because of a HW or SW crash.
+		"halted"    Shutdown because of a halt command.
+		"poweroff"  Shutdown because of a poweroff command.
+		"restart"   Shutdown because of a restart command.
+		==========  ===================================================
 
 What:		/sys/class/mic/mic(x)/cmdline
 Date:		October 2013

diff --git a/Documentation/ABI/testing/sysfs-class-ocxl b/Documentation/ABI/testing/sysfs-class-ocxl
index ae1276efa45a..bf33f4fda58f 100644
--- a/Documentation/ABI/testing/sysfs-class-ocxl
+++ b/Documentation/ABI/testing/sysfs-class-ocxl

@@ -11,8 +11,11 @@ Contact:	linuxppc-dev@lists.ozlabs.org
 Description:	read only
 		Number of contexts for the AFU, in the format <n>/<max>
 		where:
+
+			====	===============================================
 			n:	number of currently active contexts, for debug
 			max:	maximum number of contexts supported by the AFU
+			====	===============================================
 
 What:		/sys/class/ocxl/<afu name>/pp_mmio_size
 Date:		January 2018

diff --git a/Documentation/ABI/testing/sysfs-class-power b/Documentation/ABI/testing/sysfs-class-power
index dbccb2fcd7ce..d4319a04c302 100644
--- a/Documentation/ABI/testing/sysfs-class-power
+++ b/Documentation/ABI/testing/sysfs-class-power

@@ -1,4 +1,4 @@
-===== General Properties =====
+**General Properties**
 
 What:		/sys/class/power_supply/<supply_name>/manufacturer
 Date:		May 2007

@@ -72,6 +72,7 @@ Description:
 		critically low).
 
 		Access: Read, Write
+
 		Valid values: 0 - 100 (percent)
 
 What:		/sys/class/power_supply/<supply_name>/capacity_error_margin

@@ -96,7 +97,9 @@ Description:
 		Coarse representation of battery capacity.
 
 		Access: Read
-		Valid values: "Unknown", "Critical", "Low", "Normal", "High",
+
+		Valid values:
+			      "Unknown", "Critical", "Low", "Normal", "High",
 			      "Full"
 
 What:		/sys/class/power_supply/<supply_name>/current_avg

@@ -139,6 +142,7 @@ Description:
 		throttling for thermal cooling or improving battery health.
 
 		Access: Read, Write
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/charge_control_limit_max

@@ -148,6 +152,7 @@ Description:
 		Maximum legal value for the charge_control_limit property.
 
 		Access: Read
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/charge_control_start_threshold

@@ -168,6 +173,7 @@ Description:
 		stop.
 
 		Access: Read, Write
+
 		Valid values: 0 - 100 (percent)
 
 What:		/sys/class/power_supply/<supply_name>/charge_type

@@ -183,7 +189,9 @@ Description:
 		different algorithm.
 
 		Access: Read, Write
-		Valid values: "Unknown", "N/A", "Trickle", "Fast", "Standard",
+
+		Valid values:
+			      "Unknown", "N/A", "Trickle", "Fast", "Standard",
 			      "Adaptive", "Custom"
 
 What:		/sys/class/power_supply/<supply_name>/charge_term_current

@@ -194,6 +202,7 @@ Description:
 		when the battery is considered full and charging should end.
 
 		Access: Read
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/health

@@ -204,7 +213,9 @@ Description:
 		functionality.
 
 		Access: Read
-		Valid values: "Unknown", "Good", "Overheat", "Dead",
+
+		Valid values:
+			      "Unknown", "Good", "Overheat", "Dead",
 			      "Over voltage", "Unspecified failure", "Cold",
 			      "Watchdog timer expire", "Safety timer expire",
 			      "Over current", "Calibration required", "Warm",

@@ -218,6 +229,7 @@ Description:
 		for a battery charge cycle.
 
 		Access: Read
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/present

@@ -227,9 +239,13 @@ Description:
 		Reports whether a battery is present or not in the system.
 
 		Access: Read
+
 		Valid values:
+
+			== =======
 			0: Absent
 			1: Present
+			== =======
 
 What:		/sys/class/power_supply/<supply_name>/status
 Date:		May 2007

@@ -240,7 +256,9 @@ Description:
 		used to enable/disable charging to the battery.
 
 		Access: Read, Write
-		Valid values: "Unknown", "Charging", "Discharging",
+
+		Valid values:
+			      "Unknown", "Charging", "Discharging",
 			      "Not charging", "Full"
 
 What:		/sys/class/power_supply/<supply_name>/technology

@@ -250,7 +268,9 @@ Description:
 		Describes the battery technology supported by the supply.
 
 		Access: Read
-		Valid values: "Unknown", "NiMH", "Li-ion", "Li-poly", "LiFe",
+
+		Valid values:
+			      "Unknown", "NiMH", "Li-ion", "Li-poly", "LiFe",
 			      "NiCd", "LiMn"
 
 What:		/sys/class/power_supply/<supply_name>/temp

@@ -260,6 +280,7 @@ Description:
 		Reports the current TBAT battery temperature reading.
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_alert_max

@@ -274,6 +295,7 @@ Description:
 		critically high, and charging has stopped).
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_alert_min

@@ -289,6 +311,7 @@ Description:
 		remedy the situation).
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_max

@@ -299,6 +322,7 @@ Description:
 		charging.
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_min

@@ -309,6 +333,7 @@ Description:
 		charging.
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/voltage_avg,

@@ -320,6 +345,7 @@ Description:
 		which they average readings to smooth out the reported value.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
 What:		/sys/class/power_supply/<supply_name>/voltage_max,

@@ -330,6 +356,7 @@ Description:
 		during charging.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
 What:		/sys/class/power_supply/<supply_name>/voltage_min,

@@ -340,6 +367,7 @@ Description:
 		during discharging.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
 What:		/sys/class/power_supply/<supply_name>/voltage_now,

@@ -350,9 +378,10 @@ Description:
 		This value is not averaged/smoothed.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
-===== USB Properties =====
+**USB Properties**
 
 What: 		/sys/class/power_supply/<supply_name>/current_avg
 Date:		May 2007

@@ -363,6 +392,7 @@ Description:
 		average readings to smooth out the reported value.
 
 		Access: Read
+
 		Valid values: Represented in microamps
 
 

@@ -373,6 +403,7 @@ Description:
 		Reports the maximum IBUS current the supply can support.
 
 		Access: Read
+
 		Valid values: Represented in microamps
 
 What: 		/sys/class/power_supply/<supply_name>/current_now

@@ -385,6 +416,7 @@ Description:
 		within the reported min/max range.
 
 		Access: Read, Write
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/input_current_limit

@@ -399,6 +431,7 @@ Description:
 		solved using power limit use input_current_limit.
 
 		Access: Read, Write
+
 		Valid values: Represented in microamps
 
 What:		/sys/class/power_supply/<supply_name>/input_voltage_limit

@@ -441,10 +474,14 @@ Description:
 		USB supply so voltage and current can be controlled).
 
 		Access: Read, Write
+
 		Valid values:
+
+			== ==================================================
 			0: Offline
 			1: Online Fixed - Fixed Voltage Supply
 			2: Online Programmable - Programmable Voltage Supply
+			== ==================================================
 
 What:		/sys/class/power_supply/<supply_name>/temp
 Date:		May 2007

@@ -455,6 +492,7 @@ Description:
 		TJUNC temperature of an IC)
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_alert_max

@@ -470,6 +508,7 @@ Description:
 		remedy the situation).
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_alert_min

@@ -485,6 +524,7 @@ Description:
 		accordingly to remedy the situation).
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_max

@@ -494,6 +534,7 @@ Description:
 		Reports the maximum allowed supply temperature for operation.
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What:		/sys/class/power_supply/<supply_name>/temp_min

@@ -503,6 +544,7 @@ Description:
 		Reports the mainimum allowed supply temperature for operation.
 
 		Access: Read
+
 		Valid values: Represented in 1/10 Degrees Celsius
 
 What: 		/sys/class/power_supply/<supply_name>/usb_type

@@ -514,7 +556,9 @@ Description:
 		is attached.
 
 		Access: Read-Only
-		Valid values: "Unknown", "SDP", "DCP", "CDP", "ACA", "C", "PD",
+
+		Valid values:
+			      "Unknown", "SDP", "DCP", "CDP", "ACA", "C", "PD",
 			      "PD_DRP", "PD_PPS", "BrickID"
 
 What: 		/sys/class/power_supply/<supply_name>/voltage_max

@@ -524,6 +568,7 @@ Description:
 		Reports the maximum VBUS voltage the supply can support.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
 What: 		/sys/class/power_supply/<supply_name>/voltage_min

@@ -533,6 +578,7 @@ Description:
 		Reports the minimum VBUS voltage the supply can support.
 
 		Access: Read
+
 		Valid values: Represented in microvolts
 
 What: 		/sys/class/power_supply/<supply_name>/voltage_now

@@ -545,9 +591,10 @@ Description:
 		within the reported min/max range.
 
 		Access: Read, Write
+
 		Valid values: Represented in microvolts
 
-===== Device Specific Properties =====
+**Device Specific Properties**
 
 What:		/sys/class/power/ds2760-battery.*/charge_now
 Date:		May 2010

@@ -581,6 +628,7 @@ Description:
 		will drop to 0 A) and will trigger interrupt.
 
 		Valid values:
+
 		- 5, 6 or 7 (hours),
 		- 0: disabled.
 

@@ -595,6 +643,7 @@ Description:
 		will drop to 0 A) and will trigger interrupt.
 
 		Valid values:
+
 		- 4 - 16 (hours), step by 2 (rounded down)
 		- 0: disabled.
 

@@ -609,6 +658,7 @@ Description:
 		interrupt and start top-off charging mode.
 
 		Valid values:
+
 		- 100000 - 200000 (microamps), step by 25000 (rounded down)
 		- 200000 - 350000 (microamps), step by 50000 (rounded down)
 		- 0: disabled.

@@ -624,6 +674,7 @@ Description:
 		will drop to 0 A) and will trigger interrupt.
 
 		Valid values:
+
 		- 0 - 70 (minutes), step by 10 (rounded down)
 
 What:		/sys/class/power_supply/bq24257-charger/ovp_voltage

@@ -637,6 +688,7 @@ Description:
 		device datasheet for details.
 
 		Valid values:
+
 		- 6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000,
 		  10500000 (all uV)
 

@@ -652,6 +704,7 @@ Description:
 		lower than the set value. See device datasheet for details.
 
 		Valid values:
+
 		- 4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000,
 		  4760000 (all uV)
 

@@ -666,6 +719,7 @@ Description:
 		the charger operates normally. See device datasheet for details.
 
 		Valid values:
+
 		- 1: enabled
 		- 0: disabled
 

@@ -681,6 +735,7 @@ Description:
 		from the system. See device datasheet for details.
 
 		Valid values:
+
 		- 1: enabled
 		- 0: disabled
 

diff --git a/Documentation/ABI/testing/sysfs-class-power-twl4030 b/Documentation/ABI/testing/sysfs-class-power-twl4030
index b4fd32d210c5..7ac36dba87bc 100644
--- a/Documentation/ABI/testing/sysfs-class-power-twl4030
+++ b/Documentation/ABI/testing/sysfs-class-power-twl4030

@@ -4,18 +4,20 @@ Description:
 	Writing to this can disable charging.
 
 	Possible values are:
-		"auto" - draw power as appropriate for detected
-			 power source and battery status.
-		"off"  - do not draw any power.
-		"continuous"
-		       - activate mode described as "linear" in
-		         TWL data sheets.  This uses whatever
-			 current is available and doesn't switch off
-			 when voltage drops.
 
-			 This is useful for unstable power sources
-			 such as bicycle dynamo, but care should
-			 be taken that battery is not over-charged.
+		=============	===========================================
+		"auto" 		draw power as appropriate for detected
+				power source and battery status.
+		"off"  		do not draw any power.
+		"continuous"	activate mode described as "linear" in
+				TWL data sheets.  This uses whatever
+				current is available and doesn't switch off
+				when voltage drops.
+
+				This is useful for unstable power sources
+				such as bicycle dynamo, but care should
+				be taken that battery is not over-charged.
+		=============	===========================================
 
 What: /sys/class/power_supply/twl4030_ac/mode
 Description:

@@ -23,6 +25,9 @@ Description:
 	Writing to this can disable charging.
 
 	Possible values are:
-		"auto" - draw power as appropriate for detected
-			 power source and battery status.
-		"off"  - do not draw any power.
+
+		======	===========================================
+		"auto"	draw power as appropriate for detected
+			power source and battery status.
+		"off"	do not draw any power.
+		======	===========================================

diff --git a/Documentation/ABI/testing/sysfs-class-rc b/Documentation/ABI/testing/sysfs-class-rc
index 6c0d6c8cb911..9c8ff7910858 100644
--- a/Documentation/ABI/testing/sysfs-class-rc
+++ b/Documentation/ABI/testing/sysfs-class-rc

@@ -21,15 +21,22 @@ KernelVersion:	2.6.36
 Contact:	Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
 Description:
 		Reading this file returns a list of available protocols,
-		something like:
+		something like::
+
 		    "rc5 [rc6] nec jvc [sony]"
+
 		Enabled protocols are shown in [] brackets.
+
 		Writing "+proto" will add a protocol to the list of enabled
 		protocols.
+
 		Writing "-proto" will remove a protocol from the list of enabled
 		protocols.
+
 		Writing "proto" will enable only "proto".
+
 		Writing "none" will disable all protocols.
+
 		Write fails with EINVAL if an invalid protocol combination or
 		unknown protocol name is used.
 

@@ -39,11 +46,13 @@ KernelVersion:	3.15
 Contact:	Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
 Description:
 		Sets the scancode filter expected value.
+
 		Use in combination with /sys/class/rc/rcN/filter_mask to set the
 		expected value of the bits set in the filter mask.
 		If the hardware supports it then scancodes which do not match
 		the filter will be ignored. Otherwise the write will fail with
 		an error.
+
 		This value may be reset to 0 if the current protocol is altered.
 
 What:		/sys/class/rc/rcN/filter_mask

@@ -56,9 +65,11 @@ Description:
 		of the scancode which should be compared against the expected
 		value. A value of 0 disables the filter to allow all valid
 		scancodes to be processed.
+
 		If the hardware supports it then scancodes which do not match
 		the filter will be ignored. Otherwise the write will fail with
 		an error.
+
 		This value may be reset to 0 if the current protocol is altered.
 
 What:		/sys/class/rc/rcN/wakeup_protocols

@@ -67,15 +78,22 @@ KernelVersion:	4.11
 Contact:	Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
 Description:
 		Reading this file returns a list of available protocols to use
-		for the wakeup filter, something like:
+		for the wakeup filter, something like::
+
 		    "rc-5 nec nec-x rc-6-0 rc-6-6a-24 [rc-6-6a-32] rc-6-mce"
+
 		Note that protocol variants are listed, so "nec", "sony",
 		"rc-5", "rc-6" have their different bit length encodings
 		listed if available.
+
 		The enabled wakeup protocol is shown in [] brackets.
+
 		Only one protocol can be selected at a time.
+
 		Writing "proto" will use "proto" for wakeup events.
+
 		Writing "none" will disable wakeup.
+
 		Write fails with EINVAL if an invalid protocol combination or
 		unknown protocol name is used, or if wakeup is not supported by
 		the hardware.

@@ -86,13 +104,17 @@ KernelVersion:	3.15
 Contact:	Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
 Description:
 		Sets the scancode wakeup filter expected value.
+
 		Use in combination with /sys/class/rc/rcN/wakeup_filter_mask to
 		set the expected value of the bits set in the wakeup filter mask
 		to trigger a system wake event.
+
 		If the hardware supports it and wakeup_filter_mask is not 0 then
 		scancodes which match the filter will wake the system from e.g.
 		suspend to RAM or power off.
+
 		Otherwise the write will fail with an error.
+
 		This value may be reset to 0 if the wakeup protocol is altered.
 
 What:		/sys/class/rc/rcN/wakeup_filter_mask

@@ -101,11 +123,15 @@ KernelVersion:	3.15
 Contact:	Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
 Description:
 		Sets the scancode wakeup filter mask of bits to compare.
+
 		Use in combination with /sys/class/rc/rcN/wakeup_filter to set
 		the bits of the scancode which should be compared against the
 		expected value to trigger a system wake event.
+
 		If the hardware supports it and wakeup_filter_mask is not 0 then
 		scancodes which match the filter will wake the system from e.g.
 		suspend to RAM or power off.
+
 		Otherwise the write will fail with an error.
+
 		This value may be reset to 0 if the wakeup protocol is altered.

diff --git a/Documentation/ABI/testing/sysfs-class-scsi_host b/Documentation/ABI/testing/sysfs-class-scsi_host
index bafc59fd7b69..7c98d8f43c45 100644
--- a/Documentation/ABI/testing/sysfs-class-scsi_host
+++ b/Documentation/ABI/testing/sysfs-class-scsi_host

@@ -56,8 +56,9 @@ Description:
 		management) on top, which makes it match the Windows IRST (Intel
 		Rapid Storage Technology) driver settings. This setting is also
 		close to min_power, except that:
+
 		a) It does not use host-initiated slumber mode, but it does
-		allow device-initiated slumber
+		   allow device-initiated slumber
 		b) It does not enable low power device sleep mode (DevSlp).
 
 What:		/sys/class/scsi_host/hostX/em_message

@@ -70,8 +71,8 @@ Description:
 		protocol, writes and reads correspond to the LED message format
 		as defined in the AHCI spec.
 
-		The user must turn sw_activity (under /sys/block/*/device/) OFF
-		it they wish to control the activity LED via the em_message
+		The user must turn sw_activity (under `/sys/block/*/device/`)
+		OFF it they wish to control the activity LED via the em_message
 		file.
 
 		em_message_type: (RO) Displays the current enclosure management

diff --git a/Documentation/ABI/testing/sysfs-class-typec b/Documentation/ABI/testing/sysfs-class-typec
index b834671522d6..b7794e02ad20 100644
--- a/Documentation/ABI/testing/sysfs-class-typec
+++ b/Documentation/ABI/testing/sysfs-class-typec

@@ -40,10 +40,13 @@ Description:
 		attribute will not return until the operation has finished.
 
 		Valid values:
-		- source (The port will behave as source only DFP port)
-		- sink (The port will behave as sink only UFP port)
-		- dual (The port will behave as dual-role-data and
+
+		======  ==============================================
+		source  (The port will behave as source only DFP port)
+		sink    (The port will behave as sink only UFP port)
+		dual    (The port will behave as dual-role-data and
 			dual-role-power port)
+		======  ==============================================
 
 What:		/sys/class/typec/<port>/vconn_source
 Date:		April 2017

@@ -59,6 +62,7 @@ Description:
 		generates uevent KOBJ_CHANGE.
 
 		Valid values:
+
 		- "no" when the port is not the VCONN Source
 		- "yes" when the port is the VCONN Source
 

@@ -72,6 +76,7 @@ Description:
 		power operation mode should show "usb_power_delivery".
 
 		Valid values:
+
 		- default
 		- 1.5A
 		- 3.0A

@@ -191,6 +196,7 @@ Date:		April 2017
 Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
 Description:
 		Shows type of the plug on the cable:
+
 		- type-a - Standard A
 		- type-b - Standard B
 		- type-c

diff --git a/Documentation/ABI/testing/sysfs-devices-platform-ACPI-TAD b/Documentation/ABI/testing/sysfs-devices-platform-ACPI-TAD
index 7e43cdce9a52..f7b360a61b21 100644
--- a/Documentation/ABI/testing/sysfs-devices-platform-ACPI-TAD
+++ b/Documentation/ABI/testing/sysfs-devices-platform-ACPI-TAD

@@ -7,6 +7,7 @@ Description:
 		(RO) Hexadecimal bitmask of the TAD attributes are reported by
 		the platform firmware (see ACPI 6.2, section 9.18.2):
 
+		======= ======================================================
 		BIT(0): AC wakeup implemented if set
 		BIT(1): DC wakeup implemented if set
 		BIT(2): Get/set real time features implemented if set

@@ -16,6 +17,7 @@ Description:
 		BIT(6): The AC timer wakes up from S5 if set
 		BIT(7): The DC timer wakes up from S4 if set
 		BIT(8): The DC timer wakes up from S5 if set
+		======= ======================================================
 
 		The other bits are reserved.
 

@@ -62,9 +64,11 @@ Description:
 		timer status with the following meaning of bits (see ACPI 6.2,
 		Section 9.18.5):
 
+		======= ======================================================
 		Bit(0): The timer has expired if set.
 		Bit(1): The timer has woken up the system from a sleep state
 		        (S3 or S4/S5 if supported) if set.
+		======= ======================================================
 
 		The other bits are reserved.
 

diff --git a/Documentation/ABI/testing/sysfs-devices-platform-docg3 b/Documentation/ABI/testing/sysfs-devices-platform-docg3
index 8aa36716882f..378c42694bfb 100644
--- a/Documentation/ABI/testing/sysfs-devices-platform-docg3
+++ b/Documentation/ABI/testing/sysfs-devices-platform-docg3

@@ -9,8 +9,10 @@ Description:
 		The protection has information embedded whether it blocks reads,
 		writes or both.
 		The result is:
-		0 -> the DPS is not keylocked
-		1 -> the DPS is keylocked
+
+		- 0 -> the DPS is not keylocked
+		- 1 -> the DPS is keylocked
+
 Users:		None identified so far.
 
 What:		/sys/devices/platform/docg3/f[0-3]_dps[01]_protection_key

@@ -27,8 +29,12 @@ Description:
 		Entering the correct value toggle the lock, and can be observed
 		through f[0-3]_dps[01]_is_keylocked.
 		Possible values are:
+
 			- 8 bytes
+
 		Typical values are:
+
 			- "00000000"
 			- "12345678"
+
 Users:		None identified so far.

diff --git a/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb b/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb
index 2107082426da..e45ac2e865d5 100644
--- a/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb
+++ b/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb

@@ -17,10 +17,10 @@ Description:
 		to overlay planes.
 
 		Selects the composition mode for the overlay. Possible values
-		are
+		are:
 
-		0 - Alpha Blending
-		1 - ROP3
+		- 0 - Alpha Blending
+		- 1 - ROP3
 
 What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_position
 Date:		May 2012

@@ -30,7 +30,7 @@ Description:
 		to overlay planes.
 
 		Stores the x,y overlay position on the display in pixels. The
-		position format is `[0-9]+,[0-9]+'.
+		position format is `[0-9]+,[0-9]+`.
 
 What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_rop3
 Date:		May 2012

diff --git a/Documentation/ABI/testing/sysfs-devices-system-cpu b/Documentation/ABI/testing/sysfs-devices-system-cpu
index b555df825447..274c337ec6a9 100644
--- a/Documentation/ABI/testing/sysfs-devices-system-cpu
+++ b/Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -151,23 +151,28 @@ Description:
 		The processor idle states which are available for use have the
 		following attributes:
 
-		name: (RO) Name of the idle state (string).
+		======== ==== =================================================
+		name:	 (RO) Name of the idle state (string).
 
 		latency: (RO) The latency to exit out of this idle state (in
-		microseconds).
+			      microseconds).
 
-		power: (RO) The power consumed while in this idle state (in
-		milliwatts).
+		power:   (RO) The power consumed while in this idle state (in
+			      milliwatts).
 
-		time: (RO) The total time spent in this idle state (in microseconds).
+		time:    (RO) The total time spent in this idle state
+			      (in microseconds).
 
-		usage: (RO) Number of times this state was entered (a count).
+		usage:	 (RO) Number of times this state was entered (a count).
 
-		above: (RO) Number of times this state was entered, but the
-		       observed CPU idle duration was too short for it (a count).
+		above:	 (RO) Number of times this state was entered, but the
+			      observed CPU idle duration was too short for it
+			      (a count).
 
-		below: (RO) Number of times this state was entered, but the
-		       observed CPU idle duration was too long for it (a count).
+		below: 	 (RO) Number of times this state was entered, but the
+			      observed CPU idle duration was too long for it
+			      (a count).
+		======== ==== =================================================
 
 What:		/sys/devices/system/cpu/cpuX/cpuidle/stateN/desc
 Date:		February 2008

@@ -290,6 +295,7 @@ Description:	Processor frequency boosting control
 		This switch controls the boost setting for the whole system.
 		Boosting allows the CPU and the firmware to run at a frequency
 		beyound it's nominal limit.
+
 		More details can be found in
 		Documentation/admin-guide/pm/cpufreq.rst
 

@@ -337,43 +343,57 @@ Contact:	Sudeep Holla <sudeep.holla@arm.com>
 Description:	Parameters for the CPU cache attributes
 
 		allocation_policy:
-			- WriteAllocate: allocate a memory location to a cache line
-					 on a cache miss because of a write
-			- ReadAllocate: allocate a memory location to a cache line
+			- WriteAllocate:
+					allocate a memory location to a cache line
+					on a cache miss because of a write
+			- ReadAllocate:
+					allocate a memory location to a cache line
 					on a cache miss because of a read
-			- ReadWriteAllocate: both writeallocate and readallocate
+			- ReadWriteAllocate:
+					both writeallocate and readallocate
 
-		attributes: LEGACY used only on IA64 and is same as write_policy
+		attributes:
+			    LEGACY used only on IA64 and is same as write_policy
 
-		coherency_line_size: the minimum amount of data in bytes that gets
+		coherency_line_size:
+				     the minimum amount of data in bytes that gets
 				     transferred from memory to cache
 
-		level: the cache hierarchy in the multi-level cache configuration
+		level:
+			the cache hierarchy in the multi-level cache configuration
 
-		number_of_sets: total number of sets in the cache, a set is a
+		number_of_sets:
+				total number of sets in the cache, a set is a
 				collection of cache lines with the same cache index
 
-		physical_line_partition: number of physical cache line per cache tag
+		physical_line_partition:
+				number of physical cache line per cache tag
 
-		shared_cpu_list: the list of logical cpus sharing the cache
+		shared_cpu_list:
+				the list of logical cpus sharing the cache
 
-		shared_cpu_map: logical cpu mask containing the list of cpus sharing
+		shared_cpu_map:
+				logical cpu mask containing the list of cpus sharing
 				the cache
 
-		size: the total cache size in kB
+		size:
+			the total cache size in kB
 
 		type:
 			- Instruction: cache that only holds instructions
 			- Data: cache that only caches data
 			- Unified: cache that holds both data and instructions
 
-		ways_of_associativity: degree of freedom in placing a particular block
-					of memory in the cache
+		ways_of_associativity:
+			degree of freedom in placing a particular block
+			of memory in the cache
 
 		write_policy:
-			- WriteThrough: data is written to both the cache line
+			- WriteThrough:
+					data is written to both the cache line
 					and to the block in the lower-level memory
-			- WriteBack: data is written only to the cache line and
+			- WriteBack:
+				     data is written only to the cache line and
 				     the modified cache line is written to main
 				     memory only when it is replaced
 

@@ -414,30 +434,30 @@ Description:	POWERNV CPUFreq driver's frequency throttle stats directory and
 		throttle attributes exported in the 'throttle_stats' directory:
 
 		- turbo_stat : This file gives the total number of times the max
-		frequency is throttled to lower frequency in turbo (at and above
-		nominal frequency) range of frequencies.
+		  frequency is throttled to lower frequency in turbo (at and above
+		  nominal frequency) range of frequencies.
 
 		- sub_turbo_stat : This file gives the total number of times the
-		max frequency is throttled to lower frequency in sub-turbo(below
-		nominal frequency) range of frequencies.
+		  max frequency is throttled to lower frequency in sub-turbo(below
+		  nominal frequency) range of frequencies.
 
 		- unthrottle : This file gives the total number of times the max
-		frequency is unthrottled after being throttled.
+		  frequency is unthrottled after being throttled.
 
 		- powercap : This file gives the total number of times the max
-		frequency is throttled due to 'Power Capping'.
+		  frequency is throttled due to 'Power Capping'.
 
 		- overtemp : This file gives the total number of times the max
-		frequency is throttled due to 'CPU Over Temperature'.
+		  frequency is throttled due to 'CPU Over Temperature'.
 
 		- supply_fault : This file gives the total number of times the
-		max frequency is throttled due to 'Power Supply Failure'.
+		  max frequency is throttled due to 'Power Supply Failure'.
 
 		- overcurrent : This file gives the total number of times the
-		max frequency is throttled due to 'Overcurrent'.
+		  max frequency is throttled due to 'Overcurrent'.
 
 		- occ_reset : This file gives the total number of times the max
-		frequency is throttled due to 'OCC Reset'.
+		  frequency is throttled due to 'OCC Reset'.
 
 		The sysfs attributes representing different throttle reasons like
 		powercap, overtemp, supply_fault, overcurrent and occ_reset map to

@@ -469,8 +489,9 @@ What:		/sys/devices/system/cpu/cpuX/regs/
 Date:		June 2016
 Contact:	Linux ARM Kernel Mailing list <linux-arm-kernel@lists.infradead.org>
 Description:	AArch64 CPU registers
+
 		'identification' directory exposes the CPU ID registers for
-		 identifying model and revision of the CPU.
+		identifying model and revision of the CPU.
 
 What:		/sys/devices/system/cpu/cpu#/cpu_capacity
 Date:		December 2016

@@ -497,9 +518,11 @@ Description:	Information about CPU vulnerabilities
 		vulnerabilities. The output of those files reflects the
 		state of the CPUs in the system. Possible output values:
 
+		================  ==============================================
 		"Not affected"	  CPU is not affected by the vulnerability
 		"Vulnerable"	  CPU is affected and no mitigation in effect
 		"Mitigation: $M"  CPU is affected and mitigation $M is in effect
+		================  ==============================================
 
 		See also: Documentation/admin-guide/hw-vuln/index.rst
 

@@ -515,12 +538,14 @@ Description:	Control Symetric Multi Threading (SMT)
 		control: Read/write interface to control SMT. Possible
 			 values:
 
+			 ================ =========================================
 			 "on"		  SMT is enabled
 			 "off"		  SMT is disabled
 			 "forceoff"	  SMT is force disabled. Cannot be changed.
 			 "notsupported"   SMT is not supported by the CPU
 			 "notimplemented" SMT runtime toggling is not
 					  implemented for the architecture
+			 ================ =========================================
 
 			 If control status is "forceoff" or "notsupported" writes
 			 are rejected.

diff --git a/Documentation/ABI/testing/sysfs-devices-system-ibm-rtl b/Documentation/ABI/testing/sysfs-devices-system-ibm-rtl
index 470def06ab0a..1a8ee26e92ae 100644
--- a/Documentation/ABI/testing/sysfs-devices-system-ibm-rtl
+++ b/Documentation/ABI/testing/sysfs-devices-system-ibm-rtl

@@ -5,8 +5,10 @@ Contact:        Vernon Mauery <vernux@us.ibm.com>
 Description:    The state file allows a means by which to change in and
                 out of Premium Real-Time Mode (PRTM), as well as the
                 ability to query the current state.
-                    0 => PRTM off
-                    1 => PRTM enabled
+
+                    - 0 => PRTM off
+                    - 1 => PRTM enabled
+
 Users:          The ibm-prtm userspace daemon uses this interface.
 
 

diff --git a/Documentation/ABI/testing/sysfs-driver-bd9571mwv-regulator b/Documentation/ABI/testing/sysfs-driver-bd9571mwv-regulator
index 4d63a7904b94..42214b4ff14a 100644
--- a/Documentation/ABI/testing/sysfs-driver-bd9571mwv-regulator
+++ b/Documentation/ABI/testing/sysfs-driver-bd9571mwv-regulator

@@ -6,11 +6,13 @@ Description:	Read/write the current state of DDR Backup Mode, which controls
 		if DDR power rails will be kept powered during system suspend.
 		("on"/"1" = enabled, "off"/"0" = disabled).
 		Two types of power switches (or control signals) can be used:
+
 		  A. With a momentary power switch (or pulse signal), DDR
 		     Backup Mode is enabled by default when available, as the
 		     PMIC will be configured only during system suspend.
 		  B. With a toggle power switch (or level signal), the
 		     following steps must be followed exactly:
+
 		       1. Configure PMIC for backup mode, to change the role of
 			  the accessory power switch from a power switch to a
 			  wake-up switch,

@@ -20,8 +22,10 @@ Description:	Read/write the current state of DDR Backup Mode, which controls
 		       3. Suspend system,
 		       4. Switch accessory power switch on, to resume the
 			  system.
+
 		     DDR Backup Mode must be explicitly enabled by the user,
 		     to invoke step 1.
+
 		See also Documentation/devicetree/bindings/mfd/bd9571mwv.txt.
 Users:		User space applications for embedded boards equipped with a
 		BD9571MWV PMIC.

diff --git a/Documentation/ABI/testing/sysfs-driver-genwqe b/Documentation/ABI/testing/sysfs-driver-genwqe
index 64ac6d567c4b..69d855dc4c47 100644
--- a/Documentation/ABI/testing/sysfs-driver-genwqe
+++ b/Documentation/ABI/testing/sysfs-driver-genwqe

@@ -29,8 +29,12 @@ What:           /sys/class/genwqe/genwqe<n>_card/reload_bitstream
 Date:           May 2014
 Contact:        klebers@linux.vnet.ibm.com
 Description:    Interface to trigger a PCIe card reset to reload the bitstream.
+
+		::
+
                   sudo sh -c 'echo 1 > \
                     /sys/class/genwqe/genwqe0_card/reload_bitstream'
+
                 If successfully, the card will come back with the bitstream set
                 on 'next_bitstream'.
 

@@ -64,8 +68,11 @@ Description:    Base clock frequency of the card.
 What:           /sys/class/genwqe/genwqe<n>_card/device/sriov_numvfs
 Date:           Oct 2013
 Contact:        haver@linux.vnet.ibm.com
-Description:    Enable VFs (1..15):
+Description:    Enable VFs (1..15)::
+
                   sudo sh -c 'echo 15 > \
                     /sys/bus/pci/devices/0000\:1b\:00.0/sriov_numvfs'
-                Disable VFs:
+
+                Disable VFs::
+
                   Write a 0 into the same sysfs entry.

diff --git a/Documentation/ABI/testing/sysfs-driver-hid-logitech-lg4ff b/Documentation/ABI/testing/sysfs-driver-hid-logitech-lg4ff
index 305dffd229a8..de07be314efc 100644
--- a/Documentation/ABI/testing/sysfs-driver-hid-logitech-lg4ff
+++ b/Documentation/ABI/testing/sysfs-driver-hid-logitech-lg4ff

@@ -12,7 +12,9 @@ KernelVersion:	4.1
 Contact:	Michal Malý <madcatxster@devoid-pointer.net>
 Description:	Displays a set of alternate modes supported by a wheel. Each
 		mode is listed as follows:
+
 		  Tag: Mode Name
+
 		Currently active mode is marked with an asterisk. List also
 		contains an abstract item "native" which always denotes the
 		native mode of the wheel. Echoing the mode tag switches the

@@ -24,24 +26,30 @@ Description:	Displays a set of alternate modes supported by a wheel. Each
 		This entry is not created for devices that have only one mode.
 
 		Currently supported mode switches:
-		Driving Force Pro:
+
+		Driving Force Pro::
+
 		  DF-EX --> DFP
 
-		G25:
+		G25::
+
 		  DF-EX --> DFP --> G25
 
-		G27:
+		G27::
+
 		  DF-EX <*> DFP <-> G25 <-> G27
 		  DF-EX <*--------> G25 <-> G27
 		  DF-EX <*----------------> G27
 
-		G29:
+		G29::
+
 		  DF-EX <*> DFP <-> G25 <-> G27 <-> G29
 		  DF-EX <*--------> G25 <-> G27 <-> G29
 		  DF-EX <*----------------> G27 <-> G29
 		  DF-EX <*------------------------> G29
 
-		DFGT:
+		DFGT::
+
 		  DF-EX <*> DFP <-> DFGT
 		  DF-EX <*--------> DFGT
 

diff --git a/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/Documentation/ABI/testing/sysfs-driver-hid-wiimote
index 39dfa5cb1cc5..cd7b82a5c27d 100644
--- a/Documentation/ABI/testing/sysfs-driver-hid-wiimote
+++ b/Documentation/ABI/testing/sysfs-driver-hid-wiimote

@@ -39,9 +39,13 @@ Description:	While a device is initialized by the wiimote driver, we perform
 		Other strings for each device-type are available and may be
 		added if new device-specific detections are added.
 		Currently supported are:
-			gen10: First Wii Remote generation
-			gen20: Second Wii Remote Plus generation (builtin MP)
+
+			============= =======================================
+			gen10:        First Wii Remote generation
+			gen20:        Second Wii Remote Plus generation
+				      (builtin MP)
 			balanceboard: Wii Balance Board
+			============= =======================================
 
 What:		/sys/bus/hid/drivers/wiimote/<dev>/bboard_calib
 Date:		May 2013

@@ -54,6 +58,7 @@ Description:	This attribute is only provided if the device was detected as a
 		First, 0kg values for all 4 sensors are written, followed by the
 		17kg values for all 4 sensors and last the 34kg values for all 4
 		sensors.
+
 		Calibration data is already applied by the kernel to all input
 		values but may be used by user-space to perform other
 		transformations.

@@ -68,9 +73,11 @@ Description:	This attribute is only provided if the device was detected as a
 		is prefixed with a +/-. Each value is a signed 16bit number.
 		Data is encoded as decimal numbers and specifies the offsets of
 		the analog sticks of the pro-controller.
+
 		Calibration data is already applied by the kernel to all input
 		values but may be used by user-space to perform other
 		transformations.
+
 		Calibration data is detected by the kernel during device setup.
 		You can write "scan\n" into this file to re-trigger calibration.
 		You can also write data directly in the form "x1:y1 x2:y2" to

diff --git a/Documentation/ABI/testing/sysfs-driver-samsung-laptop b/Documentation/ABI/testing/sysfs-driver-samsung-laptop
index 34d3a3359cf4..28c9c040de5d 100644
--- a/Documentation/ABI/testing/sysfs-driver-samsung-laptop
+++ b/Documentation/ABI/testing/sysfs-driver-samsung-laptop

@@ -9,10 +9,12 @@ Description:	Some Samsung laptops have different "performance levels"
 		their fans quiet at all costs.  Reading from this file
 		will show the current performance level.  Writing to the
 		file can change this value.
+
 			Valid options:
-				"silent"
-				"normal"
-				"overclock"
+				- "silent"
+				- "normal"
+				- "overclock"
+
 		Note that not all laptops support all of these options.
 		Specifically, not all support the "overclock" option,
 		and it's still unknown if this value even changes

@@ -25,8 +27,9 @@ Contact:	Corentin Chary <corentin.chary@gmail.com>
 Description:	Max battery charge level can be modified, battery cycle
 		life can be extended by reducing the max battery charge
 		level.
-		0 means normal battery mode (100% charge)
-		1 means battery life extender mode (80% charge)
+
+		- 0 means normal battery mode (100% charge)
+		- 1 means battery life extender mode (80% charge)
 
 What:		/sys/devices/platform/samsung/usb_charge
 Date:		December 1, 2011

diff --git a/Documentation/ABI/testing/sysfs-driver-toshiba_acpi b/Documentation/ABI/testing/sysfs-driver-toshiba_acpi
index f34221b52b14..e5a438d84e1f 100644
--- a/Documentation/ABI/testing/sysfs-driver-toshiba_acpi
+++ b/Documentation/ABI/testing/sysfs-driver-toshiba_acpi

@@ -4,10 +4,12 @@ KernelVersion:	3.15
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the keyboard backlight operation mode, valid
 		values are:
+
 			* 0x1  -> FN-Z
 			* 0x2  -> AUTO (also called TIMER)
 			* 0x8  -> ON
 			* 0x10 -> OFF
+
 		Note that from kernel 3.16 onwards this file accepts all listed
 		parameters, kernel 3.15 only accepts the first two (FN-Z and
 		AUTO).

@@ -41,8 +43,10 @@ KernelVersion:	3.15
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This files controls the status of the touchpad and pointing
 		stick (if available), valid values are:
+
 			* 0 -> OFF
 			* 1 -> ON
+
 Users:		KToshiba
 
 What:		/sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/available_kbd_modes

@@ -51,10 +55,12 @@ KernelVersion:	3.16
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file shows the supported keyboard backlight modes
 		the system supports, which can be:
+
 			* 0x1  -> FN-Z
 			* 0x2  -> AUTO (also called TIMER)
 			* 0x8  -> ON
 			* 0x10 -> OFF
+
 		Note that not all keyboard types support the listed modes.
 		See the entry named "available_kbd_modes"
 Users:		KToshiba

@@ -65,6 +71,7 @@ KernelVersion:	3.16
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file shows the current keyboard backlight type,
 		which can be:
+
 			* 1 -> Type 1, supporting modes FN-Z and AUTO
 			* 2 -> Type 2, supporting modes TIMER, ON and OFF
 Users:		KToshiba

@@ -75,10 +82,12 @@ KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the USB Sleep & Charge charging mode, which
 		can be:
+
 			* 0 -> Disabled		(0x00)
 			* 1 -> Alternate	(0x09)
 			* 2 -> Auto		(0x21)
 			* 3 -> Typical		(0x11)
+
 		Note that from kernel 4.1 onwards this file accepts all listed
 		values, kernel 4.0 only supports the first three.
 		Note that this feature only works when connected to power, if

@@ -93,8 +102,10 @@ Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the USB Sleep Functions under battery, and
 		set the level at which point they will be disabled, accepted
 		values can be:
+
 			* 0	-> Disabled
 			* 1-100	-> Battery level to disable sleep functions
+
 		Currently it prints two values, the first one indicates if the
 		feature is enabled or disabled, while the second one shows the
 		current battery level set.

@@ -107,8 +118,10 @@ Date:		January 23, 2015
 KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the USB Rapid Charge state, which can be:
+
 			* 0 -> Disabled
 			* 1 -> Enabled
+
 		Note that toggling this value requires a reboot for changes to
 		take effect.
 Users:		KToshiba

@@ -118,8 +131,10 @@ Date:		January 23, 2015
 KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the Sleep & Music state, which values can be:
+
 			* 0 -> Disabled
 			* 1 -> Enabled
+
 		Note that this feature only works when connected to power, if
 		you want to use it under battery, see the entry named
 		"sleep_functions_on_battery"

@@ -138,6 +153,7 @@ KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the state of the internal fan, valid
 		values are:
+
 			* 0 -> OFF
 			* 1 -> ON
 

@@ -147,8 +163,10 @@ KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the Special Functions (hotkeys) operation
 		mode, valid values are:
+
 			* 0 -> Normal Operation
 			* 1 -> Special Functions
+
 		In the "Normal Operation" mode, the F{1-12} keys are as usual
 		and the hotkeys are accessed via FN-F{1-12}.
 		In the "Special Functions" mode, the F{1-12} keys trigger the

@@ -163,8 +181,10 @@ KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls whether the laptop should turn ON whenever
 		the LID is opened, valid values are:
+
 			* 0 -> Disabled
 			* 1 -> Enabled
+
 		Note that toggling this value requires a reboot for changes to
 		take effect.
 Users:		KToshiba

@@ -174,8 +194,10 @@ Date:		February 12, 2015
 KernelVersion:	4.0
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the USB 3 functionality, valid values are:
+
 			* 0 -> Disabled (Acts as a regular USB 2)
 			* 1 -> Enabled (Full USB 3 functionality)
+
 		Note that toggling this value requires a reboot for changes to
 		take effect.
 Users:		KToshiba

@@ -188,10 +210,14 @@ Description:	This file controls the Cooling Method feature.
 		Reading this file prints two values, the first is the actual cooling method
 		and the second is the maximum cooling method supported.
 		When the maximum cooling method is ONE, valid values are:
+
 			* 0 -> Maximum Performance
 			* 1 -> Battery Optimized
+
 		When the maximum cooling method is TWO, valid values are:
+
 			* 0 -> Maximum Performance
 			* 1 -> Performance
 			* 2 -> Battery Optimized
+
 Users:		KToshiba

diff --git a/Documentation/ABI/testing/sysfs-driver-toshiba_haps b/Documentation/ABI/testing/sysfs-driver-toshiba_haps
index a662370b4dbf..c938690ce10d 100644
--- a/Documentation/ABI/testing/sysfs-driver-toshiba_haps
+++ b/Documentation/ABI/testing/sysfs-driver-toshiba_haps

@@ -4,10 +4,12 @@ KernelVersion:	3.17
 Contact:	Azael Avalos <coproscefalo@gmail.com>
 Description:	This file controls the built-in accelerometer protection level,
 		valid values are:
+
 			* 0 -> Disabled
 			* 1 -> Low
 			* 2 -> Medium
 			* 3 -> High
+
 		The default potection value is set to 2 (Medium).
 Users:		KToshiba
 

diff --git a/Documentation/ABI/testing/sysfs-driver-wacom b/Documentation/ABI/testing/sysfs-driver-wacom
index afc48fc163b5..16acaa5712ec 100644
--- a/Documentation/ABI/testing/sysfs-driver-wacom
+++ b/Documentation/ABI/testing/sysfs-driver-wacom

@@ -79,7 +79,9 @@ Description:
 		When the Wacom Intuos 4 is connected over Bluetooth, the
 		image has to contain 256 bytes (64x32 px 1 bit colour).
 		The format is also scrambled, like in the USB mode, and it can
-		be summarized by converting 76543210 into GECA6420.
+		be summarized by converting::
+
+					    76543210 into GECA6420.
 					    HGFEDCBA      HFDB7531
 
 What:		/sys/bus/hid/devices/<bus>:<vid>:<pid>.<n>/wacom_remote/unpair_remote

diff --git a/Documentation/ABI/testing/sysfs-firmware-acpi b/Documentation/ABI/testing/sysfs-firmware-acpi
index 613f42a9d5cd..e4afc2538210 100644
--- a/Documentation/ABI/testing/sysfs-firmware-acpi
+++ b/Documentation/ABI/testing/sysfs-firmware-acpi

@@ -12,11 +12,14 @@ Description:
 		image: The image bitmap. Currently a 32-bit BMP.
 		status: 1 if the image is valid, 0 if firmware invalidated it.
 		type: 0 indicates image is in BMP format.
+
+		======== ===================================================
 		version: The version of the BGRT. Currently 1.
 		xoffset: The number of pixels between the left of the screen
 			 and the left edge of the image.
 		yoffset: The number of pixels between the top of the screen
 			 and the top edge of the image.
+		======== ===================================================
 
 What:		/sys/firmware/acpi/hotplug/
 Date:		February 2013

@@ -33,12 +36,14 @@ Description:
 		The following setting is available to user space for each
 		hotplug profile:
 
+		======== =======================================================
 		enabled: If set, the ACPI core will handle notifications of
-			hotplug events associated with the given class of
-			devices and will allow those devices to be ejected with
-			the help of the _EJ0 control method.  Unsetting it
-			effectively disables hotplug for the correspoinding
-			class of devices.
+			 hotplug events associated with the given class of
+			 devices and will allow those devices to be ejected with
+			 the help of the _EJ0 control method.  Unsetting it
+			 effectively disables hotplug for the correspoinding
+			 class of devices.
+		======== =======================================================
 
 		The value of the above attribute is an integer number: 1 (set)
 		or 0 (unset).  Attempts to write any other values to it will

@@ -71,86 +76,90 @@ Description:
 		To figure out where all the SCI's are coming from,
 		/sys/firmware/acpi/interrupts contains a file listing
 		every possible source, and the count of how many
-		times it has triggered.
-
-		$ cd /sys/firmware/acpi/interrupts
-		$ grep . *
-		error:	     0
-		ff_gbl_lock:	   0   enable
-		ff_pmtimer:	  0  invalid
-		ff_pwr_btn:	  0   enable
-		ff_rt_clk:	 2  disable
-		ff_slp_btn:	  0  invalid
-		gpe00:	     0	invalid
-		gpe01:	     0	 enable
-		gpe02:	   108	 enable
-		gpe03:	     0	invalid
-		gpe04:	     0	invalid
-		gpe05:	     0	invalid
-		gpe06:	     0	 enable
-		gpe07:	     0	 enable
-		gpe08:	     0	invalid
-		gpe09:	     0	invalid
-		gpe0A:	     0	invalid
-		gpe0B:	     0	invalid
-		gpe0C:	     0	invalid
-		gpe0D:	     0	invalid
-		gpe0E:	     0	invalid
-		gpe0F:	     0	invalid
-		gpe10:	     0	invalid
-		gpe11:	     0	invalid
-		gpe12:	     0	invalid
-		gpe13:	     0	invalid
-		gpe14:	     0	invalid
-		gpe15:	     0	invalid
-		gpe16:	     0	invalid
-		gpe17:	  1084	 enable
-		gpe18:	     0	 enable
-		gpe19:	     0	invalid
-		gpe1A:	     0	invalid
-		gpe1B:	     0	invalid
-		gpe1C:	     0	invalid
-		gpe1D:	     0	invalid
-		gpe1E:	     0	invalid
-		gpe1F:	     0	invalid
-		gpe_all:    1192
-		sci:	1194
-		sci_not:     0	
-
-		sci - The number of times the ACPI SCI
-		has been called and claimed an interrupt.
-
-		sci_not - The number of times the ACPI SCI
-		has been called and NOT claimed an interrupt.
-
-		gpe_all - count of SCI caused by GPEs.
-
-		gpeXX - count for individual GPE source
-
-		ff_gbl_lock - Global Lock
-
-		ff_pmtimer - PM Timer
-
-		ff_pwr_btn - Power Button
-
-		ff_rt_clk - Real Time Clock
-
-		ff_slp_btn - Sleep Button
-
-		error - an interrupt that can't be accounted for above.
-
-		invalid: it's either a GPE or a Fixed Event that
-			doesn't have an event handler.
-
-		disable: the GPE/Fixed Event is valid but disabled.
-
-		enable: the GPE/Fixed Event is valid and enabled.
-
-		Root has permission to clear any of these counters.  Eg.
-		# echo 0 > gpe11
-
-		All counters can be cleared by clearing the total "sci":
-		# echo 0 > sci
+		times it has triggered::
+
+		  $ cd /sys/firmware/acpi/interrupts
+		  $ grep . *
+		  error:	     0
+		  ff_gbl_lock:	   0   enable
+		  ff_pmtimer:	  0  invalid
+		  ff_pwr_btn:	  0   enable
+		  ff_rt_clk:	 2  disable
+		  ff_slp_btn:	  0  invalid
+		  gpe00:	     0	invalid
+		  gpe01:	     0	 enable
+		  gpe02:	   108	 enable
+		  gpe03:	     0	invalid
+		  gpe04:	     0	invalid
+		  gpe05:	     0	invalid
+		  gpe06:	     0	 enable
+		  gpe07:	     0	 enable
+		  gpe08:	     0	invalid
+		  gpe09:	     0	invalid
+		  gpe0A:	     0	invalid
+		  gpe0B:	     0	invalid
+		  gpe0C:	     0	invalid
+		  gpe0D:	     0	invalid
+		  gpe0E:	     0	invalid
+		  gpe0F:	     0	invalid
+		  gpe10:	     0	invalid
+		  gpe11:	     0	invalid
+		  gpe12:	     0	invalid
+		  gpe13:	     0	invalid
+		  gpe14:	     0	invalid
+		  gpe15:	     0	invalid
+		  gpe16:	     0	invalid
+		  gpe17:	  1084	 enable
+		  gpe18:	     0	 enable
+		  gpe19:	     0	invalid
+		  gpe1A:	     0	invalid
+		  gpe1B:	     0	invalid
+		  gpe1C:	     0	invalid
+		  gpe1D:	     0	invalid
+		  gpe1E:	     0	invalid
+		  gpe1F:	     0	invalid
+		  gpe_all:    1192
+		  sci:	1194
+		  sci_not:     0
+
+		===========  ==================================================
+		sci	     The number of times the ACPI SCI
+			     has been called and claimed an interrupt.
+
+		sci_not	     The number of times the ACPI SCI
+			     has been called and NOT claimed an interrupt.
+
+		gpe_all	     count of SCI caused by GPEs.
+
+		gpeXX	     count for individual GPE source
+
+		ff_gbl_lock  Global Lock
+
+		ff_pmtimer   PM Timer
+
+		ff_pwr_btn   Power Button
+
+		ff_rt_clk    Real Time Clock
+
+		ff_slp_btn   Sleep Button
+
+		error	     an interrupt that can't be accounted for above.
+
+		invalid      it's either a GPE or a Fixed Event that
+			     doesn't have an event handler.
+
+		disable	     the GPE/Fixed Event is valid but disabled.
+
+		enable       the GPE/Fixed Event is valid and enabled.
+		===========  ==================================================
+
+		Root has permission to clear any of these counters.  Eg.::
+
+		  # echo 0 > gpe11
+
+		All counters can be cleared by clearing the total "sci"::
+
+		  # echo 0 > sci
 
 		None of these counters has an effect on the function
 		of the system, they are simply statistics.

@@ -165,32 +174,34 @@ Description:
 
 		Let's take power button fixed event for example, please kill acpid
 		and other user space applications so that the machine won't shutdown
-		when pressing the power button.
-		# cat ff_pwr_btn
-		0	enabled
-		# press the power button for 3 times;
-		# cat ff_pwr_btn
-		3	enabled
-		# echo disable > ff_pwr_btn
-		# cat ff_pwr_btn
-		3	disabled
-		# press the power button for 3 times;
-		# cat ff_pwr_btn
-		3	disabled
-		# echo enable > ff_pwr_btn
-		# cat ff_pwr_btn
-		4	enabled
-		/*
-		 * this is because the status bit is set even if the enable bit is cleared,
-		 * and it triggers an ACPI fixed event when the enable bit is set again
-		 */
-		# press the power button for 3 times;
-		# cat ff_pwr_btn
-		7	enabled
-		# echo disable > ff_pwr_btn
-		# press the power button for 3 times;
-		# echo clear > ff_pwr_btn	/* clear the status bit */
-		# echo disable > ff_pwr_btn
-		# cat ff_pwr_btn
-		7	enabled
+		when pressing the power button::
+
+		  # cat ff_pwr_btn
+		  0	enabled
+		  # press the power button for 3 times;
+		  # cat ff_pwr_btn
+		  3	enabled
+		  # echo disable > ff_pwr_btn
+		  # cat ff_pwr_btn
+		  3	disabled
+		  # press the power button for 3 times;
+		  # cat ff_pwr_btn
+		  3	disabled
+		  # echo enable > ff_pwr_btn
+		  # cat ff_pwr_btn
+		  4	enabled
+		  /*
+		   * this is because the status bit is set even if the enable
+		   * bit is cleared, and it triggers an ACPI fixed event when
+		   * the enable bit is set again
+		   */
+		  # press the power button for 3 times;
+		  # cat ff_pwr_btn
+		  7	enabled
+		  # echo disable > ff_pwr_btn
+		  # press the power button for 3 times;
+		  # echo clear > ff_pwr_btn	/* clear the status bit */
+		  # echo disable > ff_pwr_btn
+		  # cat ff_pwr_btn
+		  7	enabled
 

diff --git a/Documentation/ABI/testing/sysfs-firmware-dmi-entries b/Documentation/ABI/testing/sysfs-firmware-dmi-entries
index 210ad44b95a5..fe0289c87768 100644
--- a/Documentation/ABI/testing/sysfs-firmware-dmi-entries
+++ b/Documentation/ABI/testing/sysfs-firmware-dmi-entries

@@ -33,7 +33,7 @@ Description:
 		doesn't matter), they will be represented in sysfs as
 		entries "T-0" through "T-(N-1)":
 
-		Example entry directories:
+		Example entry directories::
 
 			/sys/firmware/dmi/entries/17-0
 			/sys/firmware/dmi/entries/17-1

@@ -50,61 +50,65 @@ Description:
 		Each DMI entry in sysfs has the common header values
 		exported as attributes:
 
-		handle	: The 16bit 'handle' that is assigned to this
+		========  =================================================
+		handle	  The 16bit 'handle' that is assigned to this
 			  entry by the firmware.  This handle may be
 			  referred to by other entries.
-		length	: The length of the entry, as presented in the
+		length	  The length of the entry, as presented in the
 			  entry itself.  Note that this is _not the
 			  total count of bytes associated with the
-			  entry_.  This value represents the length of
+			  entry.  This value represents the length of
 			  the "formatted" portion of the entry.  This
 			  "formatted" region is sometimes followed by
 			  the "unformatted" region composed of nul
 			  terminated strings, with termination signalled
 			  by a two nul characters in series.
-		raw	: The raw bytes of the entry. This includes the
+		raw	  The raw bytes of the entry. This includes the
 			  "formatted" portion of the entry, the
 			  "unformatted" strings portion of the entry,
 			  and the two terminating nul characters.
-		type	: The type of the entry.  This value is the same
+		type	  The type of the entry.  This value is the same
 			  as found in the directory name.  It indicates
 			  how the rest of the entry should be interpreted.
-		instance: The instance ordinal of the entry for the
+		instance  The instance ordinal of the entry for the
 			  given type.  This value is the same as found
 			  in the parent directory name.
-		position: The ordinal position (zero-based) of the entry
+		position  The ordinal position (zero-based) of the entry
 			  within the entirety of the DMI entry table.
+		========  =================================================
 
-		=== Entry Specialization ===
+		**Entry Specialization**
 
 		Some entry types may have other information available in
 		sysfs.  Not all types are specialized.
 
-		--- Type 15 - System Event Log ---
+		**Type 15 - System Event Log**
 
 		This entry allows the firmware to export a log of
 		events the system has taken.  This information is
 		typically backed by nvram, but the implementation
 		details are abstracted by this table.  This entry's data
-		is exported in the directory:
+		is exported in the directory::
 
-		/sys/firmware/dmi/entries/15-0/system_event_log
+		  /sys/firmware/dmi/entries/15-0/system_event_log
 
 		and has the following attributes (documented in the
 		SMBIOS / DMI specification under "System Event Log (Type 15)":
 
-		area_length
-		header_start_offset
-		data_start_offset
-		access_method
-		status
-		change_token
-		access_method_address
-		header_format
-		per_log_type_descriptor_length
-		type_descriptors_supported_count
+		- area_length
+		- header_start_offset
+		- data_start_offset
+		- access_method
+		- status
+		- change_token
+		- access_method_address
+		- header_format
+		- per_log_type_descriptor_length
+		- type_descriptors_supported_count
 
 		As well, the kernel exports the binary attribute:
 
-		raw_event_log	: The raw binary bits of the event log
+		=============	  ====================================
+		raw_event_log	  The raw binary bits of the event log
 				  as described by the DMI entry.
+		=============	  ====================================

diff --git a/Documentation/ABI/testing/sysfs-firmware-gsmi b/Documentation/ABI/testing/sysfs-firmware-gsmi
index 0faa0aaf4b6a..7a558354c1ee 100644
--- a/Documentation/ABI/testing/sysfs-firmware-gsmi
+++ b/Documentation/ABI/testing/sysfs-firmware-gsmi

@@ -20,7 +20,7 @@ Description:
 
 			This directory has the same layout (and
 			underlying implementation as /sys/firmware/efi/vars.
-			See Documentation/ABI/*/sysfs-firmware-efi-vars
+			See `Documentation/ABI/*/sysfs-firmware-efi-vars`
 			for more information on how to interact with
 			this structure.
 

diff --git a/Documentation/ABI/testing/sysfs-firmware-memmap b/Documentation/ABI/testing/sysfs-firmware-memmap
index eca0d65087dc..1f6f4d3a32c0 100644
--- a/Documentation/ABI/testing/sysfs-firmware-memmap
+++ b/Documentation/ABI/testing/sysfs-firmware-memmap

@@ -20,7 +20,7 @@ Description:
 		the raw memory map to userspace.
 
 		The structure is as follows: Under /sys/firmware/memmap there
-		are subdirectories with the number of the entry as their name:
+		are subdirectories with the number of the entry as their name::
 
 			/sys/firmware/memmap/0
 			/sys/firmware/memmap/1

@@ -34,14 +34,16 @@ Description:
 
 		Each directory contains three files:
 
-		start	: The start address (as hexadecimal number with the
+		========  =====================================================
+		start	  The start address (as hexadecimal number with the
 			  '0x' prefix).
-		end	: The end address, inclusive (regardless whether the
+		end	  The end address, inclusive (regardless whether the
 			  firmware provides inclusive or exclusive ranges).
-		type	: Type of the entry as string. See below for a list of
+		type	  Type of the entry as string. See below for a list of
 			  valid types.
+		========  =====================================================
 
-		So, for example:
+		So, for example::
 
 			/sys/firmware/memmap/0/start
 			/sys/firmware/memmap/0/end

@@ -57,9 +59,8 @@ Description:
 		  - reserved
 
 		Following shell snippet can be used to display that memory
-		map in a human-readable format:
+		map in a human-readable format::
 
-		-------------------- 8< ----------------------------------------
 		  #!/bin/bash
 		  cd /sys/firmware/memmap
 		  for dir in * ; do

@@ -68,4 +69,3 @@ Description:
 		      type=$(cat $dir/type)
 		      printf "%016x-%016x (%s)\n" $start $[ $end +1] "$type"
 		  done
-		-------------------- >8 ----------------------------------------

diff --git a/Documentation/ABI/testing/sysfs-fs-ext4 b/Documentation/ABI/testing/sysfs-fs-ext4
index 78604db56279..99e3d92f8299 100644
--- a/Documentation/ABI/testing/sysfs-fs-ext4
+++ b/Documentation/ABI/testing/sysfs-fs-ext4

@@ -45,8 +45,8 @@ Description:
 		parameter will have their blocks allocated out of a
 		block group specific preallocation pool, so that small
 		files are packed closely together.  Each large file
-		 will have its blocks allocated out of its own unique
-		 preallocation pool.
+		will have its blocks allocated out of its own unique
+		preallocation pool.
 
 What:		/sys/fs/ext4/<disk>/inode_readahead_blks
 Date:		March 2008

diff --git a/Documentation/ABI/testing/sysfs-hypervisor-xen b/Documentation/ABI/testing/sysfs-hypervisor-xen
index 53b7b2ea7515..4dbe0c49b393 100644
--- a/Documentation/ABI/testing/sysfs-hypervisor-xen
+++ b/Documentation/ABI/testing/sysfs-hypervisor-xen

@@ -15,14 +15,17 @@ KernelVersion:	4.3
 Contact:	Boris Ostrovsky <boris.ostrovsky@oracle.com>
 Description:	If running under Xen:
 		Describes mode that Xen's performance-monitoring unit (PMU)
-		uses. Accepted values are
-			"off"  -- PMU is disabled
-			"self" -- The guest can profile itself
-			"hv"   -- The guest can profile itself and, if it is
+		uses. Accepted values are:
+
+			======    ============================================
+			"off"     PMU is disabled
+			"self"    The guest can profile itself
+			"hv"      The guest can profile itself and, if it is
 				  privileged (e.g. dom0), the hypervisor
-			"all" --  The guest can profile itself, the hypervisor
+			"all"     The guest can profile itself, the hypervisor
 				  and all other guests. Only available to
 				  privileged guests.
+			======    ============================================
 
 What:           /sys/hypervisor/pmu/pmu_features
 Date:           August 2015

diff --git a/Documentation/ABI/testing/sysfs-kernel-boot_params b/Documentation/ABI/testing/sysfs-kernel-boot_params
index eca38ce2852d..7f9bda453c4d 100644
--- a/Documentation/ABI/testing/sysfs-kernel-boot_params
+++ b/Documentation/ABI/testing/sysfs-kernel-boot_params

@@ -23,16 +23,17 @@ Description:	The /sys/kernel/boot_params directory contains two
 		representation of setup_data type. "data" file is the binary
 		representation of setup_data payload.
 
-		The whole boot_params directory structure is like below:
-		/sys/kernel/boot_params
-		|__ data
-		|__ setup_data
-		|   |__ 0
-		|   |   |__ data
-		|   |   |__ type
-		|   |__ 1
-		|       |__ data
-		|       |__ type
-		|__ version
+		The whole boot_params directory structure is like below::
+
+		  /sys/kernel/boot_params
+		  |__ data
+		  |__ setup_data
+		  |   |__ 0
+		  |   |   |__ data
+		  |   |   |__ type
+		  |   |__ 1
+		  |       |__ data
+		  |       |__ type
+		  |__ version
 
 Users:		Kexec

diff --git a/Documentation/ABI/testing/sysfs-kernel-mm-hugepages b/Documentation/ABI/testing/sysfs-kernel-mm-hugepages
index fdaa2162fae1..294387e2c7fb 100644
--- a/Documentation/ABI/testing/sysfs-kernel-mm-hugepages
+++ b/Documentation/ABI/testing/sysfs-kernel-mm-hugepages

@@ -7,9 +7,11 @@ Description:
 		of the hugepages supported by the kernel/CPU combination.
 
 		Under these directories are a number of files:
-			nr_hugepages
-			nr_overcommit_hugepages
-			free_hugepages
-			surplus_hugepages
-			resv_hugepages
+
+			- nr_hugepages
+			- nr_overcommit_hugepages
+			- free_hugepages
+			- surplus_hugepages
+			- resv_hugepages
+
 		See Documentation/admin-guide/mm/hugetlbpage.rst for details.

diff --git a/Documentation/ABI/testing/sysfs-platform-asus-laptop b/Documentation/ABI/testing/sysfs-platform-asus-laptop
index 8b0e8205a6a2..c78d358dbdbe 100644
--- a/Documentation/ABI/testing/sysfs-platform-asus-laptop
+++ b/Documentation/ABI/testing/sysfs-platform-asus-laptop

@@ -4,13 +4,16 @@ KernelVersion:	2.6.20
 Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
 		This file allows display switching. The value
-		is composed by 4 bits and defined as follow:
-		4321
-		|||`- LCD
-		||`-- CRT
-		|`--- TV
-		`---- DVI
-		Ex: - 0 (0000b) means no display
+		is composed by 4 bits and defined as follow::
+
+		  4321
+		  |||`- LCD
+		  ||`-- CRT
+		  |`--- TV
+		  `---- DVI
+
+		Ex:
+		    - 0 (0000b) means no display
 		    - 3 (0011b) CRT+LCD.
 
 What:		/sys/devices/platform/asus_laptop/gps

@@ -28,8 +31,10 @@ Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
 		Some models like the W1N have a LED display that can be
 		used to display several items of information.
-		To control the LED display, use the following :
+		To control the LED display, use the following::
+
 		    echo 0x0T000DDD > /sys/devices/platform/asus_laptop/
+
 		where T control the 3 letters display, and DDD the 3 digits display.
 		The DDD table can be found in Documentation/admin-guide/laptops/asus-laptop.rst
 

diff --git a/Documentation/ABI/testing/sysfs-platform-asus-wmi b/Documentation/ABI/testing/sysfs-platform-asus-wmi
index 1efac0ddb417..04885738cf15 100644
--- a/Documentation/ABI/testing/sysfs-platform-asus-wmi
+++ b/Documentation/ABI/testing/sysfs-platform-asus-wmi

@@ -5,6 +5,7 @@ Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
 		Change CPU clock configuration (write-only).
 		There are three available clock configuration:
+
 		    * 0 -> Super Performance Mode
 		    * 1 -> High Performance Mode
 		    * 2 -> Power Saving Mode

diff --git a/Documentation/ABI/testing/sysfs-platform-at91 b/Documentation/ABI/testing/sysfs-platform-at91
index 4cc6a865ae66..b146be74b8e0 100644
--- a/Documentation/ABI/testing/sysfs-platform-at91
+++ b/Documentation/ABI/testing/sysfs-platform-at91

@@ -18,8 +18,10 @@ Description:
 		In order to use an extended can_id add the
 		CAN_EFF_FLAG (0x80000000U) to the can_id. Example:
 
-		- standard id 0x7ff:
-		echo 0x7ff      > /sys/class/net/can0/mb0_id
+		- standard id 0x7ff::
 
-		- extended id 0x1fffffff:
-		echo 0x9fffffff > /sys/class/net/can0/mb0_id
+		    echo 0x7ff      > /sys/class/net/can0/mb0_id
+
+		- extended id 0x1fffffff::
+
+		    echo 0x9fffffff > /sys/class/net/can0/mb0_id

diff --git a/Documentation/ABI/testing/sysfs-platform-eeepc-laptop b/Documentation/ABI/testing/sysfs-platform-eeepc-laptop
index 5b026c69587a..70dbe0733cf6 100644
--- a/Documentation/ABI/testing/sysfs-platform-eeepc-laptop
+++ b/Documentation/ABI/testing/sysfs-platform-eeepc-laptop

@@ -4,9 +4,11 @@ KernelVersion:	2.6.26
 Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
 		This file allows display switching.
+
 		- 1 = LCD
 		- 2 = CRT
 		- 3 = LCD+CRT
+
 		If you run X11, you should use xrandr instead.
 
 What:		/sys/devices/platform/eeepc/camera

@@ -30,16 +32,20 @@ Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
 		Change CPU clock configuration.
 		On the Eee PC 1000H there are three available clock configuration:
+
 		    * 0 -> Super Performance Mode
 		    * 1 -> High Performance Mode
 		    * 2 -> Power Saving Mode
+
 		On Eee PC 701 there is only 2 available clock configurations.
 		Available configuration are listed in available_cpufv file.
 		Reading this file will show the raw hexadecimal value which
-		is defined as follow:
-		| 8 bit | 8 bit |
-		    |       `---- Current mode
-		    `------------ Availables modes
+		is defined as follow::
+
+		  | 8 bit | 8 bit |
+		      |       `---- Current mode
+		      `------------ Availables modes
+
 		For example, 0x301 means: mode 1 selected, 3 available modes.
 
 What:		/sys/devices/platform/eeepc/available_cpufv

diff --git a/Documentation/ABI/testing/sysfs-platform-ideapad-laptop b/Documentation/ABI/testing/sysfs-platform-ideapad-laptop
index 1b31be3f996a..fd2ac02bc5bd 100644
--- a/Documentation/ABI/testing/sysfs-platform-ideapad-laptop
+++ b/Documentation/ABI/testing/sysfs-platform-ideapad-laptop

@@ -12,6 +12,7 @@ Contact:	"Maxim Mikityanskiy <maxtram95@gmail.com>"
 Description:
 		Change fan mode
 		There are four available modes:
+
 			* 0 -> Super Silent Mode
 			* 1 -> Standard Mode
 			* 2 -> Dust Cleaning

@@ -32,9 +33,11 @@ KernelVersion:	4.18
 Contact:	"Oleg Keri <ezhi99@gmail.com>"
 Description:
 		Control fn-lock mode.
+
 			* 1 -> Switched On
 			* 0 -> Switched Off
 
-		For example:
-		# echo "0" >	\
-		/sys/bus/pci/devices/0000:00:1f.0/PNP0C09:00/VPC2004:00/fn_lock
+		For example::
+
+		  # echo "0" >	\
+		  /sys/bus/pci/devices/0000:00:1f.0/PNP0C09:00/VPC2004:00/fn_lock

diff --git a/Documentation/ABI/testing/sysfs-platform-intel-wmi-thunderbolt b/Documentation/ABI/testing/sysfs-platform-intel-wmi-thunderbolt
index 8af65059d519..e19144fd5d86 100644
--- a/Documentation/ABI/testing/sysfs-platform-intel-wmi-thunderbolt
+++ b/Documentation/ABI/testing/sysfs-platform-intel-wmi-thunderbolt

@@ -7,5 +7,6 @@ Description:
 		Thunderbolt controllers to turn on or off when no
 		devices are connected (write-only)
 		There are two available states:
+
 		    * 0 -> Force power disabled
 		    * 1 -> Force power enabled

diff --git a/Documentation/ABI/testing/sysfs-platform-sst-atom b/Documentation/ABI/testing/sysfs-platform-sst-atom
index 0d07c0395660..d5f6e21f0e42 100644
--- a/Documentation/ABI/testing/sysfs-platform-sst-atom
+++ b/Documentation/ABI/testing/sysfs-platform-sst-atom

@@ -5,13 +5,22 @@ Contact:	"Sebastien Guiriec" <sebastien.guiriec@intel.com>
 Description:
 		LPE Firmware version for SST driver on all atom
 		plaforms (BYT/CHT/Merrifield/BSW).
-		If the FW has never been loaded it will display:
+		If the FW has never been loaded it will display::
+
 			"FW not yet loaded"
-		If FW has been loaded it will display:
+
+		If FW has been loaded it will display::
+
 			"v01.aa.bb.cc"
+
 		aa: Major version is reflecting SoC version:
+
+			=== =============
 			0d: BYT FW
 			0b: BSW FW
 			07: Merrifield FW
+			=== =============
+
 		bb: Minor version
+
 		cc: Build version

diff --git a/Documentation/ABI/testing/sysfs-platform-usbip-vudc b/Documentation/ABI/testing/sysfs-platform-usbip-vudc
index 81fcfb454913..53622d3ba27c 100644
--- a/Documentation/ABI/testing/sysfs-platform-usbip-vudc
+++ b/Documentation/ABI/testing/sysfs-platform-usbip-vudc

@@ -16,10 +16,13 @@ Contact:	Krzysztof Opasiak <k.opasiak@samsung.com>
 Description:
 		Current status of the device.
 		Allowed values:
-		1 - Device is available and can be exported
-		2 - Device is currently exported
-		3 - Fatal error occurred during communication
-		  with peer
+
+		==  ==========================================
+		1   Device is available and can be exported
+		2   Device is currently exported
+		3   Fatal error occurred during communication
+		    with peer
+		==  ==========================================
 
 What:		/sys/devices/platform/usbip-vudc.%d/usbip_sockfd
 Date:		April 2016

diff --git a/Documentation/ABI/testing/sysfs-ptp b/Documentation/ABI/testing/sysfs-ptp
index a17f817a9309..2363ad810ddb 100644
--- a/Documentation/ABI/testing/sysfs-ptp
+++ b/Documentation/ABI/testing/sysfs-ptp

@@ -69,7 +69,7 @@ Description:
 		pin offered by the PTP hardware clock. The file name
 		is the hardware dependent pin name. Reading from this
 		file produces two numbers, the assigned function (see
-		the PTP_PF_ enumeration values in linux/ptp_clock.h)
+		the `PTP_PF_` enumeration values in linux/ptp_clock.h)
 		and the channel number. The function and channel
 		assignment may be changed by two writing numbers into
 		the file.