[PATCH v1 1/2] Bluetooth: btusb: define HCI packet sizes of USB Alts

@@ -459,6 +459,22 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
 #define BTUSB_WAKEUP_DISABLE	14
 #define BTUSB_USE_ALT1_FOR_WBS	15
 
+/* Per core spec 5, vol 4, part B, table 2.1,
+ * list the hci packet payload sizes for various ALT settings.
+ * This is used to set the packet length for the wideband speech.
+ * If a controller does not probe its usb alt setting, the default
+ * value will be 0. Any clients at upper layers should interpret it
+ * as a default value and set a proper packet length accordingly.
+ *
+ * To calculate the HCI packet payload length:
+ *   for alternate settings 1 - 5:
+ *     hci_packet_size = suggested_max_packet_size * 3 (packets) -
+ *                       3 (HCI header octets)
+ *   for alternate setting 6:
+ *     hci_packet_size = suggested_max_packet_size - 3 (HCI header octets)
+ */
+static const int hci_packet_size_usb_alt[] = { 0, 24, 48, 72, 96, 144, 60 };
+
 struct btusb_data {
 	struct hci_dev       *hdev;
 	struct usb_device    *udev;

@@ -3958,6 +3974,15 @@ static int btusb_probe(struct usb_interface *intf,
 	hdev->notify = btusb_notify;
 	hdev->prevent_wake = btusb_prevent_wake;
 
+	if (id->driver_info & BTUSB_AMP) {
+		/* AMP controllers do not support SCO packets */
+		data->isoc = NULL;
+	} else {
+		/* Interface orders are hardcoded in the specification */
+		data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
+		data->isoc_ifnum = ifnum_base + 1;
+	}
+
 #ifdef CONFIG_PM
 	err = btusb_config_oob_wake(hdev);
 	if (err)

@@ -4021,6 +4046,10 @@ static int btusb_probe(struct usb_interface *intf,
 		hdev->set_diag = btintel_set_diag;
 		hdev->set_bdaddr = btintel_set_bdaddr;
 		hdev->cmd_timeout = btusb_intel_cmd_timeout;
+
+		if (btusb_find_altsetting(data, 6))
+			hdev->sco_pkt_len = hci_packet_size_usb_alt[6];
+
 		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
 		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);

@@ -4062,15 +4091,6 @@ static int btusb_probe(struct usb_interface *intf,
 		btusb_check_needs_reset_resume(intf);
 	}
 
-	if (id->driver_info & BTUSB_AMP) {
-		/* AMP controllers do not support SCO packets */
-		data->isoc = NULL;
-	} else {
-		/* Interface orders are hardcoded in the specification */
-		data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
-		data->isoc_ifnum = ifnum_base + 1;
-	}
-
 	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
 	    (id->driver_info & BTUSB_REALTEK)) {
 		hdev->setup = btrtl_setup_realtek;

@@ -4082,9 +4102,10 @@ static int btusb_probe(struct usb_interface *intf,
 		 * (DEVICE_REMOTE_WAKEUP)
 		 */
 		set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
-		if (btusb_find_altsetting(data, 1))
+		if (btusb_find_altsetting(data, 1)) {
 			set_bit(BTUSB_USE_ALT1_FOR_WBS, &data->flags);
-		else
+			hdev->sco_pkt_len = hci_packet_size_usb_alt[1];
+		} else
 			bt_dev_err(hdev, "Device does not support ALT setting 1");
 	}
 

@@ -417,6 +417,7 @@ struct hci_dev {
 	unsigned int	acl_pkts;
 	unsigned int	sco_pkts;
 	unsigned int	le_pkts;
+	unsigned int	sco_pkt_len;
 
 	__u16		block_len;
 	__u16		block_mtu;