[PATCH 1/2] net: phy: micrel.c: add rgmii interface delay possibility to ksz9131
From: Philippe Schenker <hidden>
Date: 2020-03-25 15:03:50
Also in:
linux-devicetree, lkml
Subsystem:
ethernet phy library, networking drivers, the rest · Maintainers:
Andrew Lunn, Heiner Kallweit, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This patch makes use of those delays. The information which delays should be enabled or disabled comes from the interface names, documented in ethernet-controller.yaml: rgmii: Disable RXC and TXC delays rgmii-id: Enable RXC and TXC delays rgmii-txid: Enable only TXC delay, disable RXC delay rgmii-rxid: Enable onlx RXC delay, disable TXC delay Signed-off-by: Philippe Schenker <redacted> --- drivers/net/phy/micrel.c | 45 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 63dedec0433d..d3ad09774847 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c@@ -704,6 +704,48 @@ static int ksz9131_of_load_skew_values(struct phy_device *phydev, return phy_write_mmd(phydev, 2, reg, newval); } +/* MMD Address 0x2 */ +#define KSZ9131RN_RXC_DLL_CTRL 76 +#define KSZ9131RN_TXC_DLL_CTRL 77 +#define KSZ9131RN_DLL_CTRL_BYPASS BIT_MASK(12) +#define KSZ9131RN_DLL_ENABLE_DELAY 0 +#define KSZ9131RN_DLL_DISABLE_DELAY BIT(12) + +static int ksz9131_config_rgmii_delay(struct phy_device *phydev) +{ + int ret; + u16 rxcdll_val, txcdll_val; + + switch (phydev->interface) { + case PHY_INTERFACE_MODE_RGMII: + rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + break; + case PHY_INTERFACE_MODE_RGMII_ID: + rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; + txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; + break; + case PHY_INTERFACE_MODE_RGMII_RXID: + rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; + txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + break; + case PHY_INTERFACE_MODE_RGMII_TXID: + rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; + break; + default: + return 0; + } + + ret = phy_modify_mmd_changed(phydev, 2, KSZ9131RN_RXC_DLL_CTRL, + KSZ9131RN_DLL_CTRL_BYPASS, rxcdll_val); + if (ret < 0) + return ret; + + return phy_modify_mmd_changed(phydev, 2, KSZ9131RN_TXC_DLL_CTRL, + KSZ9131RN_DLL_CTRL_BYPASS, txcdll_val); +} + static int ksz9131_config_init(struct phy_device *phydev) { const struct device *dev = &phydev->mdio.dev;
@@ -730,6 +772,9 @@ static int ksz9131_config_init(struct phy_device *phydev) if (!of_node) return 0; + if (phy_interface_is_rgmii(phydev)) + ksz9131_config_rgmii_delay(phydev); + ret = ksz9131_of_load_skew_values(phydev, of_node, MII_KSZ9031RN_CLK_PAD_SKEW, 5, clk_skews, 2);
--
2.26.0