On Thu, Nov 29, 2018 at 05:23:09PM -0600, Grygorii Strashko wrote:

On 11/29/18 9:26 AM, Ivan Khoronzhuk wrote:

quoted

On Wed, Nov 28, 2018 at 03:15:46PM -0600, Grygorii Strashko wrote:

quoted

On 11/26/18 2:07 PM, Ivan Khoronzhuk wrote:

quoted

On Mon, Nov 26, 2018 at 12:57:20PM -0600, Grygorii Strashko wrote:

quoted

On 11/26/18 10:26 AM, Ivan Khoronzhuk wrote:

quoted

On Sun, Nov 25, 2018 at 05:46:26PM -0600, Grygorii Strashko wrote:

quoted

In dual_mac mode CPSW driver uses vid1 and vid2 by default to implement
dual mac mode wich are used to configure pvids for each external ports.
But, historicaly, it also adds vid0 to ALE table and sets "untag" bits for both
ext. ports. As result, it's imposible to use priority tagged packets in
dual mac mode.

Hence, drop vid0 configuration in dual mac mode as it's not required for dual
mac mode functionality and, this way, make it possible to use priority
tagged packet in dual mac mode.

So, now it's enabled to be added via regular ndo.
I have similar change in mind, but was going to send it after
mcast/ucast, and - enabling same vlans patch...

2 things stopped me to add this:

1) Moving it to be enabled via regular call is Ok, but in dual mac mode
it causes overlaps, at least while vid deletion. So decided to wait till
same vlans series is applied.

TI driver documentation mentions this restriction
"While adding VLAN id to the eth interfaces,
same VLAN id should not be added in both interfaces which will lead to VLAN
forwarding and act as switch"

It's not accurate now.
This sw bug "acting like a switch" was fixed indirectly in LKML ).
And at least for upstream version, not TISDK, desc should be updated,
but better do this when it fixed completely and merged with TISDK.

I know about this "written" restriction
(for tiSDK, and it's not TRM after all ...),
it can be avoided and it's partly avoided now ...

I'd like to clarify point about supporting same VLANs in dual_mac mode,
to avoid future misunderstanding, overall: it's *not* supported as
adding same VLAN to both netdevices will cause unknown unicast packets
leaking between interfaces and it can't be avoided - hw limitation.

Simple test shows no issues with ucast leaking.
But for current buggy ucast vlan implementation it's not possible to verify,
not sure but probably leaking in your case cuased by hidden toggling of
interface to promisc while added ucast to vlans or other reason or so.
Anyway I just decided to check specifically ucasts
(macst as you know are not normal now).

For verification you need to apply ucast fix (including vlans) first:
https://git.linaro.org/people/ivan.khoronzhuk/tsn_kernel.git/log/?h=vlan_addr_flt_fix

This is generic fix (not sure it will be approved, need try RFC) but implement
the same as local fix for vlan ucasts:
https://git.linaro.org/people/ivan.khoronzhuk/tsn_kernel.git/log/?h=ucast_vlan_fix

Any of those are correct. I've used generic one.
Applied the following scheme:

                     +--------------------------+
                     | host 74:DA:EA:47:7D:9C   |
                     +--------------------------+

                        +---------------------+
             |       am572 evm     |
                        |    eth0      eth1   |
                        +----------+----------+
                        | eth0.400 | eth1.400 |
                        +----------+----------+
                            ^          |
                            |          |  +-----------+
+-----------------+        |          |  |     PC    |
| BBB eth0.400    |--------+          +->| Wireshark |
+-----------------+                      +-----------+


1) Configure vlans on am572x evm
ip link add link eth0 name eth0.400 type vlan id 400
ip link add link eth1 name eth1.400 type vlan id 400

2) On BBB side:
# ip link add link eth0 name eth0.400 type vlan id 400
Send ucast vlan traffic to the am572 evm, vlan ucast address is unreq on am572.
# ./plget -i eth0.400 -t ptpl2 -m tx-lat -n 160 -s 10 -a 74:DA:EA:47:7D:66
# ./plget -i eth0.400 -t ptpl2 -m tx-lat -n 160 -s 10 -a 18:03:73:66:87:42

3) Observe silence on PC wireshark.

Thus, no see issues with this.

PS: I'm sure in plget tool, you can use your own.

I'm using packeth to generate udp packets (vlan) src=PC dst=unknown
if there is record in ALE table which looks like:
type: vlan , vid = 100, untag_force = 0x0, reg_mcast = 0x7, unreg_mcast = 0x0, member_list = 0x7
then above udp packet will be forwarded to BBB.

Agree, seems no normal way to avoid ucast leak.

-- 
regards,
-grygorii

-- 
Regards,
Ivan Khoronzhuk