On Sun, Apr 30, 2017 at 11:04 AM, Sebastian Reichel [off-list ref] wrote:

Hi,

On Sun, Apr 30, 2017 at 10:14:20AM -0500, Adam Ford wrote:

quoted

On Wed, Apr 5, 2017 at 1:30 PM, Rob Herring [off-list ref] wrote:

quoted

This series adds serdev support to the HCI LL protocol used on TI BT
modules and enables support on HiKey board with with the WL1835 module.
With this the custom TI UIM daemon and btattach are no longer needed.

Without UIM daemon, what instruction do you use to load the BT firmware?

I was thinking 'hciattach' but I was having trouble.  I was hoping you
might have some insight.

 hciattach -t 30 -s 115200 /dev/ttymxc1 texas 3000000 flow  Just
returns a timeout.

I modified my i.MX6 device tree per the binding documentation and
setup the regulators and enable GPIO pins.

If you configured everything correctly no userspace interaction is
required. The driver should request the firmware automatically once
you power up the bluetooth device.

Apart from DT changes make sure, that the following options are
enabled and check dmesg for any hints.

CONFIG_SERIAL_DEV_BUS
CONFIG_SERIAL_DEV_CTRL_TTYPORT
CONFIG_BT_HCIUART
CONFIG_BT_HCIUART_LL

I have enabled those flags, and I have updated my device tree.
I am testing this on an OMAP3630 (DM3730) board with a WL1283.  I am
getting a lot of timeout errors.  I tested this against the original
implemention I had in pdata-quirks.c using the ti-st driver, uim & and
the btwilink driver.

I pulled in some of the newer patches to enable the wl1283-st, but I
am obviously missing something.

I   58.717651] Bluetooth: hci0: Reading TI version information failed
(-110)
[   58.724853] Bluetooth: hci0: download firmware failed, retrying...
[   60.957641] Bluetooth: hci0 command 0x1001 tx timeout
[   68.957641] Bluetooth: hci0: Reading TI version information failed
(-110)
[   68.964843] Bluetooth: hci0: download firmware failed, retrying...
[   69.132171] Bluetooth: Unknown HCI packet type 06
[   69.138244] Bluetooth: Unknown HCI packet type 0c
[   69.143249] Bluetooth: Unknown HCI packet type 40
[   69.148498] Bluetooth: Unknown HCI packet type 20
[   69.153533] Bluetooth: Data length is too large
[   69.158569] Bluetooth: Unknown HCI packet type a0
[   69.163574] Bluetooth: Unknown HCI packet type 00
[   69.168731] Bluetooth: Unknown HCI packet type 00
[   69.173736] Bluetooth: Unknown HCI packet type 34
[   69.178924] Bluetooth: Unknown HCI packet type 91
[   71.197631] Bluetooth: hci0 command 0x1001 tx timeout
[   79.197662] Bluetooth: hci0: Reading TI version information failed (-110)

Since the pdata-quirks and original ti-st drivers work together, I
know the hardware is fine.  The only change to the device tree is the
addition of the Bluetooth container:

bluetooth {
  compatible = "ti,wl1283-st";
  enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
};

Any thoughts or suggestions to try?  I get similar behavior on an
i.MX6 board with a wl1837-st module as well.

adam

-- Sebastian

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html