[PATCH] Drivers: net: ieee802154: mrf24j40: fix some space around operator coding style issues
From: weizhewang <hidden>
Date: 2015-03-08 03:34:19
Also in:
lkml
Subsystem:
ieee 802.15.4 subsystem, mrf24j40 ieee 802.15.4 radio driver, networking drivers, the rest · Maintainers:
Alexander Aring, Stefan Schmidt, Miquel Raynal, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
Fixed some codeing style issues. Signed-off-by: hmsjwzb[off-list ref] --- drivers/net/ieee802154/mrf24j40.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c
index fba2dfd..d35c7a0 100644
--- a/drivers/net/ieee802154/mrf24j40.c
+++ b/drivers/net/ieee802154/mrf24j40.c@@ -235,9 +235,9 @@ static int write_tx_buf(struct mrf24j40 *devrec, u16 reg, }; /* Range check the length. 2 bytes are used for the length fields.*/ - if (length > TX_FIFO_SIZE-2) { + if (length > TX_FIFO_SIZE - 2) { dev_err(printdev(devrec), "write_tx_buf() was passed too large a buffer. Performing short write.\n"); - length = TX_FIFO_SIZE-2; + length = TX_FIFO_SIZE - 2; } spi_message_init(&msg);
@@ -290,9 +290,9 @@ static int mrf24j40_read_rx_buf(struct mrf24j40 *devrec, /* Range check the RX FIFO length, accounting for the one-byte * length field at the beginning. */ - if (rx_len > RX_FIFO_SIZE-1) { + if (rx_len > RX_FIFO_SIZE - 1) { dev_err(printdev(devrec), "Invalid length read from device. Performing short read.\n"); - rx_len = RX_FIFO_SIZE-1; + rx_len = RX_FIFO_SIZE - 1; } if (rx_len > *len) {
@@ -302,7 +302,7 @@ static int mrf24j40_read_rx_buf(struct mrf24j40 *devrec, } /* Set up the commands to read the data. */ - cmd = MRF24J40_READLONG(REG_RX_FIFO+1); + cmd = MRF24J40_READLONG(REG_RX_FIFO + 1); addr[0] = cmd >> 8 & 0xff; addr[1] = cmd & 0xff; data_xfer.len = rx_len;
@@ -402,7 +402,7 @@ static int mrf24j40_start(struct ieee802154_hw *hw) ret = read_short_reg(devrec, REG_INTCON, &val); if (ret) return ret; - val &= ~(0x1|0x8); /* Clear TXNIE and RXIE. Enable interrupts */ + val &= ~(0x1 | 0x8); /* Clear TXNIE and RXIE. Enable interrupts */ write_short_reg(devrec, REG_INTCON, val); return 0;
@@ -419,7 +419,7 @@ static void mrf24j40_stop(struct ieee802154_hw *hw) ret = read_short_reg(devrec, REG_INTCON, &val); if (ret) return; - val |= 0x1|0x8; /* Set TXNIE and RXIE. Disable Interrupts */ + val |= 0x1 | 0x8; /* Set TXNIE and RXIE. Disable Interrupts */ write_short_reg(devrec, REG_INTCON, val); }
@@ -436,7 +436,7 @@ static int mrf24j40_set_channel(struct ieee802154_hw *hw, u8 page, u8 channel) WARN_ON(channel > MRF24J40_CHAN_MAX); /* Set Channel TODO */ - val = (channel-11) << 4 | 0x03; + val = (channel - 11) << 4 | 0x03; write_long_reg(devrec, REG_RFCON0, val); /* RF Reset */
@@ -558,7 +558,7 @@ static int mrf24j40_handle_rx(struct mrf24j40 *devrec) } /* Cut off the checksum */ - skb_trim(skb, len-2); + skb_trim(skb, len - 2); /* TODO: Other drivers call ieee20154_rx_irqsafe() here (eg: cc2040, * also from a workqueue). I think irqsafe is not necessary here.
--
1.9.1