Re: [PATCH net] gso: do GSO for local skb with size bigger than MTU

On Mon, Dec 01, 2014 at 01:52:25PM +0000, Thomas Graf wrote:

On 11/30/14 at 10:08am, Du, Fan wrote:

quoted

quoted

-----Original Message-----
From: Jason Wang [mailto:jasowang@redhat.com]
Sent: Friday, November 28, 2014 3:02 PM
To: Du, Fan
Cc: netdev@vger.kernel.org; davem@davemloft.net; fw@strlen.de; Du, Fan
Subject: Re: [PATCH net] gso: do GSO for local skb with size bigger than MTU
On Fri, Nov 28, 2014 at 2:33 PM, Fan Du [off-list ref] wrote:

quoted

Test scenario: two KVM guests sitting in different hosts communicate
to each other with a vxlan tunnel.

All interface MTU is default 1500 Bytes, from guest point of view, its
skb gso_size could be as bigger as 1448Bytes, however after guest skb
goes through vxlan encapuslation, individual segments length of a gso
packet could exceed physical NIC MTU 1500, which will be lost at
recevier side.

So it's possible in virtualized environment, locally created skb len
after encapslation could be bigger than underlayer MTU. In such case,
it's reasonable to do GSO first, then fragment any packet bigger than
MTU as possible.

+---------------+ TX     RX +---------------+
|   KVM Guest   | -> ... -> |   KVM Guest   |
+-+-----------+-+           +-+-----------+-+
  |Qemu/VirtIO|               |Qemu/VirtIO|
  +-----------+               +-----------+
       |                            |
       v tap0                  tap0 v
  +-----------+               +-----------+
  | ovs bridge|               | ovs bridge|
  +-----------+               +-----------+
       | vxlan                vxlan |
       v                            v
  +-----------+               +-----------+
  |    NIC    |    <------>   |    NIC    |
  +-----------+               +-----------+

Steps to reproduce:
 1. Using kernel builtin openvswitch module to setup ovs bridge.
 2. Runing iperf without -M, communication will stuck.

Is this issue specific to ovs or ipv4? Path MTU discovery should help in this case I
believe.

Problem here is host stack push local over-sized gso skb down to NIC, and perform GSO there
without any further ip segmentation.

Reasonable behavior is do gso first at ip level, if gso-ed skb is bigger than MTU && df is set, 
Then push ICMP_DEST_UNREACH/ICMP_FRAG_NEEDED message back to sender to adjust mtu.

Sounds about right.

Aside from this. I think Virtio should provide a MTU hint to the guest
to adjust MTU in the vNIC to account for both overhead or support for
jumbo frames in the underlay transparently without relying on PMTU or
MSS hints. I remember we talked about this a while ago with at least
Michael but haven't done actual code work on it yet.

This can be an optimization but can't replace fixing PMTU.
In particular this can't help legacy guests.

quoted

For PMTU to work, that's another issue I will try to address later on.

PMTU discovery was explicitly removed from the OVS datapath. Maybe
Pravin or Jesse can provide some background on that

PMTU was never working properly for OVS users.  There was an ugly hack that kind
of worked part of the time.  That was dropped, and good riddance.
Proper PMTU support for all kind of tunneling solutions, e.g. along the
lines you outline above, belongs in host core.

-- 
MST
_______________________________________________
dev mailing list
dev@openvswitch.org
http://openvswitch.org/mailman/listinfo/dev