[net-next 07/12] igb: SerDes flow control setting
flat view
STALE4902d
REVIEWED: 1 (0M)
From: Jeff Kirsher <hidden>
Date: 2013-05-21 22:03:31
Subsystem:
intel ethernet drivers, networking drivers, the rest · Maintainers:
Tony Nguyen, Przemek Kitszel, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
1 review trailer.
From: "Akeem G. Abodunrin" <redacted> This path allows users to get appropriate flow control setting on SerDes devices, based on original implementation for Copper devices. Also, since 100baseFX does not support setting flow control, so exclude it from the setting mechanism. Signed-off-by: Akeem G Abodunrin <redacted> Tested-by: Aaron Brown <redacted> Signed-off-by: Jeff Kirsher <redacted> --- drivers/net/ethernet/intel/igb/igb_ethtool.c | 34 ++++++++++++++++------------ 1 file changed, 19 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 4e54f84..7b25ee2 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c@@ -164,21 +164,6 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) ecmd->advertising |= hw->phy.autoneg_advertised; } - if (hw->mac.autoneg != 1) - ecmd->advertising &= ~(ADVERTISED_Pause | - ADVERTISED_Asym_Pause); - - if (hw->fc.requested_mode == e1000_fc_full) - ecmd->advertising |= ADVERTISED_Pause; - else if (hw->fc.requested_mode == e1000_fc_rx_pause) - ecmd->advertising |= (ADVERTISED_Pause | - ADVERTISED_Asym_Pause); - else if (hw->fc.requested_mode == e1000_fc_tx_pause) - ecmd->advertising |= ADVERTISED_Asym_Pause; - else - ecmd->advertising &= ~(ADVERTISED_Pause | - ADVERTISED_Asym_Pause); - ecmd->port = PORT_TP; ecmd->phy_address = hw->phy.addr; ecmd->transceiver = XCVR_INTERNAL;
@@ -206,6 +191,21 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) ecmd->transceiver = XCVR_EXTERNAL; } + if (hw->mac.autoneg != 1) + ecmd->advertising &= ~(ADVERTISED_Pause | + ADVERTISED_Asym_Pause); + + if (hw->fc.requested_mode == e1000_fc_full) + ecmd->advertising |= ADVERTISED_Pause; + else if (hw->fc.requested_mode == e1000_fc_rx_pause) + ecmd->advertising |= (ADVERTISED_Pause | + ADVERTISED_Asym_Pause); + else if (hw->fc.requested_mode == e1000_fc_tx_pause) + ecmd->advertising |= ADVERTISED_Asym_Pause; + else + ecmd->advertising &= ~(ADVERTISED_Pause | + ADVERTISED_Asym_Pause); + status = rd32(E1000_STATUS); if (status & E1000_STATUS_LU) {
@@ -386,6 +386,10 @@ static int igb_set_pauseparam(struct net_device *netdev, struct e1000_hw *hw = &adapter->hw; int retval = 0; + /* 100basefx does not support setting link flow control */ + if (hw->dev_spec._82575.eth_flags.e100_base_fx) + return -EINVAL; + adapter->fc_autoneg = pause->autoneg; while (test_and_set_bit(__IGB_RESETTING, &adapter->state))
--
1.7.11.7