[net-next 11/13] igb: Enable auto-crossover during forced operation on 82580 and above.
flat view
From: Jeff Kirsher <hidden>
Date: 2012-10-30 07:04:37
Subsystem:
intel ethernet drivers, networking drivers, the rest · Maintainers:
Tony Nguyen, Przemek Kitszel, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
From: Matthew Vick <redacted> Newer devices supported by igb can support auto-crossover detection in forced operation modes. Enable this in the driver, rather than clobbering this functionality in forced operation. Signed-off-by: Matthew Vick <redacted> Tested-by: Aaron Brown <redacted> Signed-off-by: Jeff Kirsher <redacted> --- drivers/net/ethernet/intel/igb/e1000_mac.c | 4 ++++ drivers/net/ethernet/intel/igb/e1000_phy.c | 29 +++++++++++++++++------------ 2 files changed, 21 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/intel/igb/e1000_mac.c b/drivers/net/ethernet/intel/igb/e1000_mac.c
index 819c145..7acddfe 100644
--- a/drivers/net/ethernet/intel/igb/e1000_mac.c
+++ b/drivers/net/ethernet/intel/igb/e1000_mac.c@@ -1391,6 +1391,10 @@ s32 igb_validate_mdi_setting(struct e1000_hw *hw) { s32 ret_val = 0; + /* All MDI settings are supported on 82580 and newer. */ + if (hw->mac.type >= e1000_82580) + goto out; + if (!hw->mac.autoneg && (hw->phy.mdix == 0 || hw->phy.mdix == 3)) { hw_dbg("Invalid MDI setting detected\n"); hw->phy.mdix = 1;
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c
index c62a4c3..fe76004 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.c
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.c@@ -1207,20 +1207,25 @@ s32 igb_phy_force_speed_duplex_m88(struct e1000_hw *hw) u16 phy_data; bool link; - /* - * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI - * forced whenever speed and duplex are forced. - */ - ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - goto out; + /* I210 and I211 devices support Auto-Crossover in forced operation. */ + if (phy->type != e1000_phy_i210) { + /* + * Clear Auto-Crossover to force MDI manually. M88E1000 + * requires MDI forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, + &phy_data); + if (ret_val) + goto out; - phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; - ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - goto out; + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + ret_val = phy->ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + goto out; - hw_dbg("M88E1000 PSCR: %X\n", phy_data); + hw_dbg("M88E1000 PSCR: %X\n", phy_data); + } ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); if (ret_val)
--
1.7.11.7