Re: [Qemu-devel] macvlan/macvtap: guest/host cannot communicate when network cable is unplugged

Can you try the same test with two macvlan interfaces on the host (no
macvtap)?  You may need to use the ping -I <interface-address>
argument to force the ping source address to a specific macvlan
interface.

If you see the same problem, it may just be the macvlan design - it is
stacked on top of eth0 and might not work when eth0 is down.  CCing
macvlan/macvtap folks.

Stefan

tested as below

$ifconfig

    eth0      Link encap:Ethernet  HWaddr f4:6d:xx:xx:xx:xx
              inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:86507 errors:0 dropped:0 overruns:0 frame:0
              TX packets:55940 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:126005746 (120.1 MiB)  TX bytes:4394225 (4.1 MiB)

    macvtap0  Link encap:Ethernet  HWaddr 52:54:xx:xx:xx:xx
              inet6 addr: fe80::xx:xx:xx:xx/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:70 errors:0 dropped:0 overruns:0 frame:0
              TX packets:84 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:500
              RX bytes:9036 (8.8 KiB)  TX bytes:14734 (14.3 KiB)

    znet0     Link encap:Ethernet  HWaddr 00:60:xx:xx:xx:92
              inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
              inet6 addr: 2002:xx:xx:xx:xx/64 Scope:Global
              inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:4463190 errors:0 dropped:0 overruns:0 frame:0
              TX packets:12527522 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0
              RX bytes:3959213697 (3.6 GiB)  TX bytes:18590336476 (17.3 GiB)
             
   znet1     Link encap:Ethernet  HWaddr 00:60:xx:xx:xx:99 
              inet addr:192.168.1.177  Bcast:192.168.1.255  Mask:255.255.255.0
              inet6 addr: 2002:xx:xx:xx:xx64 Scope:Global
              inet6 addr: fe80:xx:xx:xx:xx/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:8 errors:0 dropped:0 overruns:0 frame:0
              TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0
              RX bytes:1399 (1.3 KiB)  TX bytes:1522 (1.4 KiB)

$ ip -d link show
         
    10: znet0@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT
        link/ether 00:60:xx:xx:xx:92 brd ff:ff:ff:ff:ff:ff
        macvlan  mode bridge
    15: znet1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT
        link/ether 00:60:xx:xx:xx:99 brd ff:ff:ff:ff:ff:ff
        macvlan  mode bridge


the macvlan interface cannot ping each other no matter network cable is plugged or not

$ ping -I 192.168.1.2 192.168.1.177
PING 192.168.1.177 (192.168.1.177) from 192.168.1.2 : 56(84) bytes of data.

--- 192.168.1.177 ping statistics ---

6 packets transmitted, 0 received, 100% packet loss, time 4999ms


I also perform an additional test: the guests (macvtap bridge mode) CAN communicate each other no matter network cable is plugged or not.