[PATCH v2] stmmac: Add device-tree support
From: Stefan Roese <sr@denx.de>
Date: 2012-03-13 07:23:14
Also in:
linux-devicetree
Subsystem:
networking drivers, open firmware and flattened device tree bindings, stmmac ethernet driver, the rest · Maintainers:
Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Maxime Chevallier, Linus Torvalds
This patch adds support to configure the STMMAC ethernet driver via device-tree instead of platform_data. Currently, only the properties needed on SPEAr600 are provided. All other properties should be added once needed on other platforms. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Giuseppe Cavallaro <redacted> --- v2: - Renamed stm -> st - Renamed compatible to "st,spear600-gmac" - Removed "prog-burst-len", "had-gmac", has-pmt" properties. They are now implicitly set for "st,spear600-gmac" compatible devices. - Removed phy-addr - Used "if (pdev->dev.of_node)" to distinguish between DT and non-DT version instead of #ifdef Documentation/devicetree/bindings/net/stmmac.txt | 28 ++++++++ .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 76 +++++++++++++++++++- 2 files changed, 102 insertions(+), 2 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/stmmac.txt
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
new file mode 100644
index 0000000..a91f4e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/stmmac.txt@@ -0,0 +1,28 @@ +* STMicroelectronics 10/100/1000 Ethernet driver (GMAC) + +Required properties: +- compatible: Should be "st,spear600-gmac" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain the interrupt names "macirq" + "eth_wake_irq" if this interrupt is supported in the "interrupts" + property +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii", "gmii", "rgmii". + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + gmac0: stmmac@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "gmii"; + };
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 3aad981..ed8b477 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c@@ -24,8 +24,50 @@ #include <linux/platform_device.h> #include <linux/io.h> +#include <linux/of.h> +#include <linux/of_net.h> #include "stmmac.h" +#ifdef CONFIG_OF +static int __devinit stmmac_probe_config_dt(struct platform_device *pdev, + struct plat_stmmacenet_data *plat, + const char **mac) +{ + struct device_node *np = pdev->dev.of_node; + + if (!np) + return -ENODEV; + + *mac = of_get_mac_address(np); + + plat->interface = of_get_phy_mode(np); + of_property_read_u32(np, "phy-addr", &plat->phy_addr); + plat->mdio_bus_data = devm_kzalloc(&pdev->dev, + sizeof(struct stmmac_mdio_bus_data), + GFP_KERNEL); + + /* + * Currently only the properties needed on SPEAr600 + * are provided. All other properties should be added + * once needed on other platforms. + */ + if (of_device_is_compatible(np, "st,spear600-gmac")) { + plat->pbl = 8; + plat->has_gmac = 1; + plat->pmt = 1; + } + + return 0; +} +#else +static int __devinit stmmac_probe_config_dt(struct platform_device *pdev, + struct plat_stmmacenet_data *plat, + const char **mac) +{ + return ERR_PTR(-ENOSYS); +} +#endif /* CONFIG_OF */ + /** * stmmac_pltfr_probe * @pdev: platform device pointer
@@ -39,7 +81,8 @@ static int stmmac_pltfr_probe(struct platform_device *pdev) struct resource *res; void __iomem *addr = NULL; struct stmmac_priv *priv = NULL; - struct plat_stmmacenet_data *plat_dat; + struct plat_stmmacenet_data *plat_dat = NULL; + const char *mac = NULL; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res)
@@ -58,7 +101,25 @@ static int stmmac_pltfr_probe(struct platform_device *pdev) ret = -ENOMEM; goto out_release_region; } - plat_dat = pdev->dev.platform_data; + + if (pdev->dev.of_node) { + plat_dat = devm_kzalloc(&pdev->dev, + sizeof(struct plat_stmmacenet_data), + GFP_KERNEL); + if (!plat_dat) { + pr_err("%s: ERROR: no memory", __func__); + ret = -ENOMEM; + goto out_unmap; + } + + ret = stmmac_probe_config_dt(pdev, plat_dat, &mac); + if (ret) { + pr_err("%s: main dt probe failed", __func__); + goto out_unmap; + } + } else { + plat_dat = pdev->dev.platform_data; + } /* Custom initialisation (if needed)*/ if (plat_dat->init) {
@@ -73,6 +134,10 @@ static int stmmac_pltfr_probe(struct platform_device *pdev) goto out_unmap; } + /* Get MAC address if available (DT) */ + if (mac) + memcpy(priv->dev->dev_addr, mac, ETH_ALEN); + /* Get the MAC information */ priv->dev->irq = platform_get_irq_byname(pdev, "macirq"); if (priv->dev->irq == -ENXIO) {
@@ -178,6 +243,12 @@ static const struct dev_pm_ops stmmac_pltfr_pm_ops = { static const struct dev_pm_ops stmmac_pltfr_pm_ops; #endif /* CONFIG_PM */ +static const struct of_device_id stmmac_dt_ids[] = { + { .compatible = "st,spear600-gmac", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, stmmac_dt_ids); + static struct platform_driver stmmac_driver = { .probe = stmmac_pltfr_probe, .remove = stmmac_pltfr_remove,
@@ -185,6 +256,7 @@ static struct platform_driver stmmac_driver = { .name = STMMAC_RESOURCE_NAME, .owner = THIS_MODULE, .pm = &stmmac_pltfr_pm_ops, + .of_match_table = of_match_ptr(stmmac_dt_ids), }, };
--
1.7.9.2