[PATCH 1/2] netdev/phy/icplus: Correct broken phy_init code

Subsystems: ethernet phy library, networking drivers, the rest

STALE5286d

4 messages, 2 authors, 2012-02-23 · open the first message on its own page

[PATCH 1/2] netdev/phy/icplus: Correct broken phy_init code

From: Giuseppe CAVALLARO <hidden>
Date: 2012-02-22 07:25:22

From: David McKay <redacted>

The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.

The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.

Signed-off-by: David McKay <redacted>
Signed-off-by: Giuseppe Cavallaro <redacted>
---
 drivers/net/phy/icplus.c |   24 ++++++++++++++++++------
 1 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
index c81f136..7ee4f58 100644
--- a/drivers/net/phy/icplus.c
+++ b/drivers/net/phy/icplus.c

@@ -98,20 +98,24 @@ static int ip175c_config_init(struct phy_device *phydev)
 
 static int ip1xx_reset(struct phy_device *phydev)
 {
-	int err, bmcr;
+	int bmcr;
 
 	/* Software Reset PHY */
 	bmcr = phy_read(phydev, MII_BMCR);
+	if (bmcr < 0)
+		return bmcr;
 	bmcr |= BMCR_RESET;
-	err = phy_write(phydev, MII_BMCR, bmcr);
-	if (err < 0)
-		return err;
+	bmcr = phy_write(phydev, MII_BMCR, bmcr);
+	if (bmcr < 0)
+		return bmcr;
 
 	do {
 		bmcr = phy_read(phydev, MII_BMCR);
+		if (bmcr < 0)
+			return bmcr;
 	} while (bmcr & BMCR_RESET);
 
-	return err;
+	return 0;
 }
 
 static int ip1001_config_init(struct phy_device *phydev)

@@ -124,7 +128,10 @@ static int ip1001_config_init(struct phy_device *phydev)
 
 	/* Enable Auto Power Saving mode */
 	c = phy_read(phydev, IP1001_SPEC_CTRL_STATUS_2);
+	if (c < 0)
+		return c;
 	c |= IP1001_APS_ON;
+	c = phy_write(phydev, IP1001_SPEC_CTRL_STATUS_2, c);
 	if (c < 0)
 		return c;

@@ -132,11 +139,16 @@ static int ip1001_config_init(struct phy_device *phydev)
 		/* Additional delay (2ns) used to adjust RX clock phase
 		 * at RGMII interface */
 		c = phy_read(phydev, IP10XX_SPEC_CTRL_STATUS);
+		if (c < 0)
+			return c;
+
 		c |= IP1001_PHASE_SEL_MASK;
 		c = phy_write(phydev, IP10XX_SPEC_CTRL_STATUS, c);
+		if (c < 0)
+			return c;
 	}
 
-	return c;
+	return 0;
 }
 
 static int ip101a_config_init(struct phy_device *phydev)

-- 
1.7.4.4

[PATCH 2/2] phy: IC+101G and PHY_HAS_INTERRUPT flag

From: Giuseppe CAVALLARO <hidden>
Date: 2012-02-22 07:26:38

This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.

Signed-off-by: Giuseppe Cavallaro <redacted>
---
 drivers/net/phy/icplus.c |   31 +++++++++++++++++--------------
 1 files changed, 17 insertions(+), 14 deletions(-)

diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
index 7ee4f58..0856e1b 100644
--- a/drivers/net/phy/icplus.c
+++ b/drivers/net/phy/icplus.c

@@ -30,16 +30,16 @@
 #include <asm/irq.h>
 #include <asm/uaccess.h>
 
-MODULE_DESCRIPTION("ICPlus IP175C/IP101A/IC1001 PHY drivers");
+MODULE_DESCRIPTION("ICPlus IP175C/IP101A/IP101G/IC1001 PHY drivers");
 MODULE_AUTHOR("Michael Barkowski");
 MODULE_LICENSE("GPL");
 
-/* IP101A/IP1001 */
-#define IP10XX_SPEC_CTRL_STATUS		16  /* Spec. Control Register */
-#define IP1001_SPEC_CTRL_STATUS_2	20  /* IP1001 Spec. Control Reg 2 */
-#define IP1001_PHASE_SEL_MASK		3 /* IP1001 RX/TXPHASE_SEL */
-#define IP1001_APS_ON			11  /* IP1001 APS Mode  bit */
-#define IP101A_APS_ON			2   /* IP101A APS Mode bit */
+/* IP101A/G - IP1001 */
+#define IP10XX_SPEC_CTRL_STATUS		16	/* Spec. Control Register */
+#define IP1001_SPEC_CTRL_STATUS_2	20	/* IP1001 Spec. Control Reg 2 */
+#define IP1001_PHASE_SEL_MASK		3	/* IP1001 RX/TXPHASE_SEL */
+#define IP1001_APS_ON			11	/* IP1001 APS Mode  bit */
+#define IP101A_G_APS_ON			2	/* IP101A/G APS Mode bit */
 
 static int ip175c_config_init(struct phy_device *phydev)
 {

@@ -151,7 +151,7 @@ static int ip1001_config_init(struct phy_device *phydev)
 	return 0;
 }
 
-static int ip101a_config_init(struct phy_device *phydev)
+static int ip101a_g_config_init(struct phy_device *phydev)
 {
 	int c;

@@ -161,7 +161,7 @@ static int ip101a_config_init(struct phy_device *phydev)
 
 	/* Enable Auto Power Saving mode */
 	c = phy_read(phydev, IP10XX_SPEC_CTRL_STATUS);
-	c |= IP101A_APS_ON;
+	c |= IP101A_G_APS_ON;
 	return c;
 }

@@ -203,6 +203,7 @@ static struct phy_driver ip1001_driver = {
 	.phy_id_mask	= 0x0ffffff0,
 	.features	= PHY_GBIT_FEATURES | SUPPORTED_Pause |
 			  SUPPORTED_Asym_Pause,
+	.flags		= PHY_HAS_INTERRUPT,
 	.config_init	= &ip1001_config_init,
 	.config_aneg	= &genphy_config_aneg,
 	.read_status	= &genphy_read_status,

@@ -211,13 +212,14 @@ static struct phy_driver ip1001_driver = {
 	.driver		= { .owner = THIS_MODULE,},
 };
 
-static struct phy_driver ip101a_driver = {
+static struct phy_driver ip101a_g_driver = {
 	.phy_id		= 0x02430c54,
-	.name		= "ICPlus IP101A",
+	.name		= "ICPlus IP101A/G",
 	.phy_id_mask	= 0x0ffffff0,
 	.features	= PHY_BASIC_FEATURES | SUPPORTED_Pause |
 			  SUPPORTED_Asym_Pause,
-	.config_init	= &ip101a_config_init,
+	.flags		= PHY_HAS_INTERRUPT,
+	.config_init	= &ip101a_g_config_init,
 	.config_aneg	= &genphy_config_aneg,
 	.read_status	= &genphy_read_status,
 	.suspend	= genphy_suspend,

@@ -233,7 +235,7 @@ static int __init icplus_init(void)
 	if (ret < 0)
 		return -ENODEV;
 
-	ret = phy_driver_register(&ip101a_driver);
+	ret = phy_driver_register(&ip101a_g_driver);
 	if (ret < 0)
 		return -ENODEV;

@@ -243,7 +245,7 @@ static int __init icplus_init(void)
 static void __exit icplus_exit(void)
 {
 	phy_driver_unregister(&ip1001_driver);
-	phy_driver_unregister(&ip101a_driver);
+	phy_driver_unregister(&ip101a_g_driver);
 	phy_driver_unregister(&ip175c_driver);
 }

@@ -253,6 +255,7 @@ module_exit(icplus_exit);
 static struct mdio_device_id __maybe_unused icplus_tbl[] = {
 	{ 0x02430d80, 0x0ffffff0 },
 	{ 0x02430d90, 0x0ffffff0 },
+	{ 0x02430c54, 0x0ffffff0 },
 	{ }
 };

-- 
1.7.4.4

Re: [PATCH 1/2] netdev/phy/icplus: Correct broken phy_init code

From: David Miller <davem@davemloft.net>
Date: 2012-02-23 22:14:46

From: Giuseppe CAVALLARO <redacted>
Date: Wed, 22 Feb 2012 08:24:57 +0100

From: David McKay <redacted>

The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.

The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.

Signed-off-by: David McKay <redacted>
Signed-off-by: Giuseppe Cavallaro <redacted>

Applied.

Re: [PATCH 2/2] phy: IC+101G and PHY_HAS_INTERRUPT flag

From: David Miller <davem@davemloft.net>
Date: 2012-02-23 22:14:51

From: Giuseppe CAVALLARO <redacted>
Date: Wed, 22 Feb 2012 08:26:28 +0100

This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.

Signed-off-by: Giuseppe Cavallaro <redacted>

Applied.

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help