Thread (8 messages) 8 messages, 3 authors, 2012-01-04

[PATCH] mii: Remove references to DP83840 PHY in mii.h

flat view
STALE5406d

From: Mark Einon <mark.einon@gmail.com>
Date: 2011-08-31 15:36:47
Subsystem: ethernet phy library, the rest · Maintainers: Andrew Lunn, Heiner Kallweit, Linus Torvalds

There are references to this PHY chip in the generic mii.h header, so removing them.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
---
 include/linux/mii.h |   12 ++++++------
 1 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/include/linux/mii.h b/include/linux/mii.h
index 103113a..4c3cfb5 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -40,12 +40,12 @@
 #define BMCR_CTST               0x0080  /* Collision test              */
 #define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
 #define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
-#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
-#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
+#define BMCR_ISOLATE            0x0400  /* Disconnect PHY from MII     */
+#define BMCR_PDOWN              0x0800  /* Powerdown                   */
 #define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
 #define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
 #define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
-#define BMCR_RESET              0x8000  /* Reset the DP83840           */
+#define BMCR_RESET              0x8000  /* Reset                       */
 
 /* Basic mode status register. */
 #define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
@@ -55,9 +55,9 @@
 #define BMSR_RFAULT             0x0010  /* Remote fault detected       */
 #define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
 #define BMSR_RESV               0x00c0  /* Unused...                   */
-#define BMSR_ESTATEN		0x0100	/* Extended Status in R15 */
-#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX */
-#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX */
+#define BMSR_ESTATEN		0x0100	/* Extended Status in R15      */
+#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX       */
+#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX       */
 #define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
 #define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
 #define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
-- 
1.7.6
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help