Re: [PATCH] CAN: Add Flexcan CAN controller driver

Wolfgang Grandegger wrote:

On 07/21/2010 10:42 PM, Marc Kleine-Budde wrote:

quoted

Marc Kleine-Budde wrote:

quoted

Wolfgang Grandegger wrote:

quoted

I realized a few issues. You can add my "acked-by" when they are fixed.

thanks for the review.

[...]

quoted

quoted

quoted

+static void flexcan_poll_err_frame(struct net_device *dev,
+				   struct can_frame *cf, u32 reg_esr)
+{
+	struct flexcan_priv *priv = netdev_priv(dev);
+	int error_warning = 0, rx_errors = 0, tx_errors = 0;
+
+	if (reg_esr & FLEXCAN_ESR_BIT1_ERR) {
+		rx_errors = 1;
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+		cf->data[2] |= CAN_ERR_PROT_BIT1;
+	}
+
+	if (reg_esr & FLEXCAN_ESR_BIT0_ERR) {
+		rx_errors = 1;
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+		cf->data[2] |= CAN_ERR_PROT_BIT0;
+	}
+
+	if (reg_esr & FLEXCAN_ESR_FRM_ERR) {
+		rx_errors = 1;
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+		cf->data[2] |= CAN_ERR_PROT_FORM;
+	}
+
+	if (reg_esr & FLEXCAN_ESR_STF_ERR) {
+		rx_errors = 1;
+		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+		cf->data[2] |= CAN_ERR_PROT_STUFF;
+	}
+
+
+	if (reg_esr & FLEXCAN_ESR_ACK_ERR) {
+		tx_errors = 1;
+		cf->can_id |= CAN_ERR_ACK;

This is a bus-error as well. Therefore I think it should be:

	if (reg_esr & FLEXCAN_ESR_ACK_ERR) {
		tx_errors = 1;
		cf->can_id |= CAN_ERR_ACK;
		cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
		cf->data[3] |= CAN_ERR_PROT_LOC_ACK; /* ACK slot */
	}

I need to check what CAN_ERR_ACK is intended for. Then, cf->can_id could
be preset with "CAN_ERR_PROT | CAN_ERR_BUSERROR" at the beginning.

This controller issues an ACK error if there are no other nodes on the
CAN bus to send a ACK that the message has been received. Or all
remaining Nodes are in bus off state.

Mainly this bus error can cause the infamous IRQ and message flooding
when no cable is connected.

No cable connected can (if your node doesn't have an activated on baord
termination) result in no termination at all, and this may result in a
different error.

At least it does on the at91. I haven't checked with the flexcan.

The subtile difference is that the CAN controller isn't allowed to go
into bus-off with a proper terminated bus when it recevies no ACKs, but
going to bus off on a not terminated bus is okay.

quoted

From the datasheet:
"This bit indicates that an acknowledge (ACK) error has been detected by
the transmitter node; that is, a dominant bit has not been detected
during the ACK SLOT."

That's what the above error describes, like on the SJA1000, apart from
setting CAN_ERR_ACK. Setting CAN_ERR_ACK is somehow bogus, but just
leave it for the time being. I will fix it globally when time permits.

Now I'm confused. What's the meaning of CAN_ERR_ACK? When should it be used?

Cheers, Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |