# ethtool -i eth0
driver: tg3
version: 3.97
firmware-version: 5722-v3.08, ASFIPMI v6.02
bus-info: 0000:01:00.0

Kernel version 2.6.29.4

Matt Carlson schreef:

O.K.  ASF is enabled.  Can you give me the output of 'ethtool -i eth0'
on as late a kernel (or driver version) as you can?  This should give me
the firmware version number.

On Sat, Jun 27, 2009 at 02:58:24AM -0700, Jean-Louis Dupond wrote:

quoted

Hi,

Got the output for gbit & 100mbit now.

GBIT:
eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 
00:22:19:be:c4:48
eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.


100mbit (sometimes it goes 100mbit instead of gbit also):
eth0: Tigon3 [partno(BCM95722) rev a200 PHY(5722/5756)] (PCI Express) 
10/100/1000Base-T Ethernet 00:22:19:c7:28:c3
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.


Cables are 2 meters long & cat 5e. The servers are in racks, so its all 
near each other :)


Matt Carlson schreef:

quoted

On Fri, Jun 26, 2009 at 02:33:03PM -0700, Jean-Louis Dupond wrote:

quoted

Hi,

All tested kernels had the same issue (2.6.22, 2.5.25.4 & 2.6.28.1).

O.K.  So that means the problem wasn't recently introduced.  Good to
know.

quoted

dmesg |grep tg3:

tg3.c:v3.97 (December 10, 2008)
tg3 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
tg3 0000:01:00.0: setting latency timer to 64
tg3 0000:01:00.0: PME# disabled
tg3 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
tg3 0000:02:00.0: setting latency timer to 64
tg3 0000:02:00.0: PME# disabled
tg3 0000:01:00.0: PME# disabled
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.

Now here it booted @ Gbit speeds!

The specific set of lines I'm looks something like this:

eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:10:18:15:16:b6
eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
                                        ^^^^^^
eth0: dma_rwctrl[76180000] dma_mask[64-bit]


Like Michael, I'm tempted to look into the cabling too.  How long are
they?  Silly question, but are they Cat5e?  When link does come up, does
it take unusually long?

quoted

Matt Carlson schreef:

quoted

Was there a version of the kernel where this device worked reliably?

Can you post the driver sign-on messages?  (I'm looking to see if ASF
is enabled.)

On Fri, Jun 12, 2009 at 03:16:59PM -0700, Jean-Louis Dupond wrote:

quoted

I surely tried other cables. But its surely not the cable because:
1) We tried other cables
2) After a reboot it works, or after a mii-tool -R
3) We have this issue on like +100 servers :(

The servers are connected on a Dell PowerConnect 6248 switch.

Sincerely

Michael Chan schreef:

quoted

On Fri, 2009-06-12 at 14:51 -0700, Jean-Louis Dupond wrote:

quoted

Hello!

Here is a mii-tool -vvv on a box that doesn't advertise gbit speeds! It 
just doesn't advertise gbit @ random, sometimes it does, sometimes not! 
Without any logic in it!

# mii-tool  -vvv
Using SIOCGMIIPHY=0x8947
eth0: link ok
    registers for MII PHY 1:
      1000 794d 0143 bed0 05e1 0000 0064 2001
      0000 0300 0000 0000 0000 0000 0000 3000

Register 1 shows that autoneg did not complete (bit 5 is not set).
The tg3 device has advertised 10/100/1000 in register 4 and register 9,
but registers 5 and 0xa (link partner's advertisement registers are 0).

When it works, these registers should look very different.

Have you tried other cables?  What is the link partner?

quoted

      0000 0101 0000 0000 0000 0000 0000 0000
      7477 0104 0000 ffff 2801 0000 8000 0000
    product info: vendor 00:50:ef, model 45 rev 0
    basic mode:   autonegotiation enabled
    basic status: link ok
    capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD
10baseT-FD 10baseT-HD
    advertising:  100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-
control

# dmesg | grep tg3
[    3.331702] tg3.c:v3.92.1 (June 9, 2008)
[   18.238654] tg3: eth0: Link is up at 10 Mbps, half duplex.
[   18.238654] tg3: eth0: Flow control is off for TX and off for RX.

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html