Re: [PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

Ron Mercer wrote:

[snipped some code]

+static int ql_wait_port_init_cmplt(struct ql_adapter *qdev)
+{
+	int count = 100;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, STS);
+		if (temp & qdev->port_init)
+			return 0;
+		mdelay(5);

Wrost case: delaying for 500ms... msleep() here please.

+		QPRINTK(qdev, LINK, INFO, "Wait for MAC Port to Initialize.\n");

I don't know what QPRINTK does, but it gets executed 100 times. That
can't possibly be intended?

+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+/* The CFG register is used to download TX and RX control blocks
+ * to the chip. This function waits for an operation to complete.
+ */
+static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit)
+{
+	int count = MSLEEP_COUNT;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, CFG);
+		if (!(temp & bit))
+			return 0;
+		if (temp & CFG_LE)
+			return -EIO;
+		spin_unlock(&qdev->hw_lock);
+		msleep(MSLEEP_DELAY);
+		spin_lock(&qdev->hw_lock);

If this is why mdelay() is used in the other places... keeping the locks
shouldn't hurt when changing them to msleep()? I don't see how a
possible deadlock could occur in the mdelay() scenarios. And besides, 
you seem to operate your spinlocks on a higher level than e.g. this
function? Wouldn't that render multi-cpu usage pratically useless?

+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+/* Used to issue init control blocks to hw. Maps control block,
+ * sets address, triggers download, waits for completion.
+ */
+int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
+		 u16 q_id)
+{
+	u64 map;
+	int status = 0;
+	int direction;
+	u32 mask;
+	u32 value;
+
+	direction =
+	    (bit & (CFG_LRQ | CFG_LR | CFG_LCQ)) ? PCI_DMA_TODEVICE :
+	    PCI_DMA_FROMDEVICE;
+
+	map = pci_map_single(qdev->pdev, ptr, size, direction);
+	if (pci_dma_mapping_error(map)) {
+		QPRINTK(qdev, IFUP, ERR, "Couldn't map DMA area.\n");
+		return -ENOMEM;
+	}
+
+	status = ql_wait_cfg(qdev, bit);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Timed out waiting for CFG to come ready.\n");
+		goto exit;
+	}
+
+	status = ql_sem_spinlock(qdev, SEM_ICB_MASK);
+	if (status)
+		goto exit;
+	ql_write32(qdev, ICB_L, (u32) map);
+	ql_write32(qdev, ICB_H, (u32) (map >> 32));
+	ql_sem_unlock(qdev, SEM_ICB_MASK);	/* does flush too */
+
+	mask = CFG_Q_MASK | (bit << 16);
+	value = bit | (q_id << CFG_Q_SHIFT);
+	ql_write32(qdev, CFG, (mask | value));
+
+	/*
+	 * Wait for the bit to clear after signaling hw.
+	 */
+	status = ql_wait_cfg(qdev, bit);
+exit:
+	pci_unmap_single(qdev->pdev, map, size, direction);
+	return status;
+}
+
+/* This chip has several addr/data register pairs that are used
+ * to index into another set of registers.  This function waits
+ * for a specified register set to be ready for access.
+ * Examples would be setting up the CAM with MAC addresses, setting
+ * up the frame routing table.
+ */
+static int ql_wait_idx_reg(struct ql_adapter *qdev, u32 reg, u32 flag)
+{
+	int count = 200;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, reg);
+		if (temp & flag)
+			return 0;
+		mdelay(5);

Delaying for a 1000ms worst case.

+		count--;
+	}
+	return -ETIMEDOUT;
+}

[snipped more code]

+static int ql_port_initialize(struct ql_adapter *qdev)
+{
+	int status = 0;
+	u32 data;
+
+	if (ql_sem_trylock(qdev, qdev->xg_sem_mask)) {
+		/* Another function has the semaphore, so
+		 * wait for the port init bit to come ready.
+		 */
+		QPRINTK(qdev, LINK, INFO,
+			"Another function has the semaphore, so wait for the port init bit to come ready.\n");
+		status = ql_wait_port_init_cmplt(qdev);
+		if (status) {
+			QPRINTK(qdev, LINK, CRIT,
+				"Port initialize timed out.\n");
+		}
+		return status;
+	}
+
+	QPRINTK(qdev, LINK, INFO, "Got xgmac semaphore!.\n");
+	/* Set the core reset. */
+	status = ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
+	if (status)
+		goto end;
+	data |= GLOBAL_CFG_RESET;
+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
+	if (status)
+		goto end;
+
+	mdelay(100);

Again.

+
+	/* Clear the core reset and turn on jumbo for receiver. */
+	data &= ~GLOBAL_CFG_RESET;	/* Clear core reset. */
+	data |= GLOBAL_CFG_JUMBO;	/* Turn on jumbo. */
+	data |= GLOBAL_CFG_TX_STAT_EN;
+	data |= GLOBAL_CFG_RX_STAT_EN;
+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
+	if (status)
+		goto end;
+
+	/* Enable transmitter, and clear it's reset. */
+	status = ql_read_xgmac_reg(qdev, TX_CFG, &data);
+	if (status)
+		goto end;
+	data &= ~TX_CFG_RESET;	/* Clear the TX MAC reset. */
+	data |= TX_CFG_EN;	/* Enable the transmitter. */
+	status = ql_write_xgmac_reg(qdev, TX_CFG, data);
+	if (status)
+		goto end;
+
+	/* Enable receiver and clear it's reset. */
+	status = ql_read_xgmac_reg(qdev, RX_CFG, &data);
+	if (status)
+		goto end;
+	data &= ~RX_CFG_RESET;	/* Clear the RX MAC reset. */
+	data |= RX_CFG_EN;	/* Enable the receiver. */
+	status = ql_write_xgmac_reg(qdev, RX_CFG, data);
+	if (status)
+		goto end;
+
+	/* Turn on jumbo. */
+	status =
+	    ql_write_xgmac_reg(qdev, MAC_TX_PARAMS, MAC_TX_PARAMS_JUMBO | (0x2580 << 16));
+	if (status)
+		goto end;
+	status =
+	    ql_write_xgmac_reg(qdev, MAC_RX_PARAMS, 0x2580);
+	if (status)
+		goto end;
+
+	/* Signal to the world that the port is enabled.        */
+	ql_write32(qdev, STS, ((qdev->port_init << 16) | qdev->port_init));
+end:
+	ql_sem_unlock(qdev, qdev->xg_sem_mask);
+	return status;
+}
+
+/* Get the next large buffer. */
+struct bq_desc *ql_get_curr_lbuf(struct rx_ring *rx_ring)
+{
+	struct bq_desc *lbq_desc = &rx_ring->lbq[rx_ring->lbq_curr_idx];
+	rx_ring->lbq_curr_idx++;
+	if (rx_ring->lbq_curr_idx == rx_ring->lbq_len)
+		rx_ring->lbq_curr_idx = 0;
+	rx_ring->lbq_free_cnt++;
+	return lbq_desc;
+}

[ remaining code snipped, a bit too much for today ]


Franco