Thread (13 messages) flat view 13 messages, 4 authors, 2007-08-04

Re: [REGRESSION] tg3 dead after s2ram

From: "Michael Chan" <mchan@broadcom.com>
Date: 2007-08-01 20:06:32
Also in: linux-acpi, lkml

On Wed, 2007-08-01 at 10:47 -0700, Michael Chan wrote:
You have 2 Broadcom devices in your system.  07:00.0 is a wireless
device, I think.  8:4.0 is the tg3 device.

It's clear that the tg3 device is still in D3 state after resume and
that explains why all register accesses fail.  tg3_resume() should put
the device back in D0 state in a very straight forward way and I don't
see how that can fail.  It worked for me when I tested it last night.
Can you add some printk() to tg3_resume() to see what's happening?  Let
me know if you want me to send you some debug patches to do that.
I misread the PCI registers below.  The power state was ok.

The problem is that memory enable and bus master were not set in PCI
register 4 after resume.  This also explains the register access
failures.

In tg3_resume(), we call pci_restore_state() which should re-enable
those 2 bits in PCI register 4.  Can you add some printk() to see why
those bits are not restored after pci_restore_state()?

Thanks.
Here's the before and after for 8:4.0:
quoted
Before

08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit 
Ethernet (rev 03)
	Subsystem: Acer Incorporated [ALI] Unknown device 010e
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
	Latency: 0 (16000ns min)
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 
Enable-
		Address: ffff6bfe7fffffb8  Data: fec7
00: e4 14 9c 16 06 00 b0 02 03 00 00 02 00 00 00 00
10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 20 00 00
50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
60: fe 6b ff ff c7 fe 00 00 98 00 03 30 00 00 3f 76
70: f6 10 00 00 20 00 00 80 14 04 00 00 00 00 00 00
80: 85 6b d0 36 03 40 00 0c 34 00 13 04 82 90 09 04
90: 09 97 00 01 00 00 00 00 00 00 00 00 eb 01 00 00
a0: 00 00 00 00 23 01 00 00 00 00 00 00 cb 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

After

08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit 
Ethernet (rev 03)
	Subsystem: Acer Incorporated [ALI] Unknown device 010e
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- 
SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at d0300000 (32-bit, non-prefetchable) [disabled] [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
	Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 
Enable-
		Address: ffff6bfe7fffffb8  Data: fec7
00: e4 14 9c 16 00 00 b0 02 03 00 00 02 00 00 00 00
10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64
50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
60: fe 6b ff ff c7 fe 00 00 9a 00 03 30 00 00 00 00
70: 76 10 00 00 40 00 00 00 50 00 00 00 00 00 00 00
80: 03 58 fc 00 00 00 00 00 00 00 00 00 fe 90 09 04
90: 01 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help