@@ -0,0 +1,234 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,cpm1-tsa.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PowerQUICC CPM Time-slot assigner (TSA) controller
+
+maintainers:
+  - Herve Codina <herve.codina@bootlin.com>
+
+description:
+  The TSA is the time-slot assigner that can be found on some PowerQUICC SoC.
+  Its purpose is to route some TDM time-slots to other internal serial
+  controllers.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - fsl,mpc885-tsa
+          - fsl,mpc866-tsa
+      - const: fsl,cpm1-tsa
+
+  reg:
+    items:
+      - description: SI (Serial Interface) register base
+      - description: SI RAM base
+
+  reg-names:
+    items:
+      - const: si_regs
+      - const: si_ram
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  '#fsl,serial-cells':
+    $ref: /schemas/types.yaml#/definitions/uint32
+    const: 1
+    description:
+      TSA consumers that use a phandle to TSA need to pass the serial identifier
+      with this phandle (defined in dt-bindings/soc/fsl,tsa.h).
+      For instance "fsl,tsa-serial = <&tsa FSL_CPM_TSA_SCC4>;".
+
+patternProperties:
+  '^tdm@[0-1]$':
+    description:
+      The TDM managed by this controller
+    type: object
+
+    additionalProperties: false
+
+    properties:
+      reg:
+        minimum: 0
+        maximum: 1
+        description:
+          The TDM number for this TDM, 0 for TDMa and 1 for TDMb
+
+      fsl,common-rxtx-pins:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The hardware can use four dedicated pins for Tx clock, Tx sync, Rx
+          clock and Rx sync or use only two pins, Tx/Rx clock and Tx/Rx sync.
+          Without the 'fsl,common-rxtx-pins' property, the four pins are used.
+          With the 'fsl,common-rxtx-pins' property, two pins are used.
+
+      clocks:
+        minItems: 2
+        items:
+          - description: External clock connected to L1RSYNC pin
+          - description: External clock connected to L1RCLK pin
+          - description: External clock connected to L1TSYNC pin
+          - description: External clock connected to L1TCLK pin
+      clock-names:
+        minItems: 2
+        items:
+          - const: l1rsync
+          - const: l1rclk
+          - const: l1tsync
+          - const: l1tclk
+
+      fsl,diagnostic-mode:
+        $ref: /schemas/types.yaml#/definitions/string
+        enum: [disabled, echo, internal-loopback, control-loopback]
+        default: disabled
+        description: |
+          The diagnostic mode can be used to diagnose some communication issues.
+          It should not be set (or set to 'disabled') when diagnostic is not
+          needed.
+          Diagnostic mode:
+            - disabled:
+                Diagnostic disabled (ie. normal operation)
+            - echo:
+                Automatic echo. Rx data is resent on Tx.
+            - internal-loopback:
+                The TDM transmitter is connected to the receiver. Data appears
+                on Tx pin.
+            - control-loopback:
+                The TDM transmitter is connected to the receiver. The Tx pin is
+                disconnected.
+
+      fsl,rx-frame-sync-delay-bits:
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Receive frame sync delay in number of bits.
+          Indicates the delay between the Rx sync and the first bit of the Rx
+          frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay.
+
+      fsl,tx-frame-sync-delay-bits:
+        enum: [0, 1, 2, 3]
+        default: 0
+        description: |
+          Transmit frame sync delay in number of bits.
+          Indicates the delay between the Tx sync and the first bit of the Tx
+          frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay.
+
+      fsl,clock-falling-edge:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Data is sent on falling edge of the clock (and received on the rising
+          edge). If 'clock-falling-edge' is not present, data is sent on the
+          rising edge (and received on the falling edge).
+
+      fsl,fsync-rising-edge:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Frame sync pulses are sampled with the rising edge of the channel
+          clock. If 'fsync-rising-edge' is not present, pulses are sampled with
+          the falling edge.
+
+      fsl,double-speed-clock:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          The channel clock is twice the data rate.
+
+    patternProperties:
+      '^fsl,[rt]x-ts-routes$':
+        $ref: /schemas/types.yaml#/definitions/uint32-matrix
+        description: |
+          A list of tuple that indicates the Tx or Rx time-slots routes.
+        items:
+          items:
+            - description:
+                The number of time-slots
+              minimum: 1
+              maximum: 64
+            - description: |
+                The source (Tx) or destination (Rx) serial interface
+                (dt-bindings/soc/fsl,tsa.h defines these values)
+                 - 0: No destination
+                 - 1: SCC2
+                 - 2: SCC3
+                 - 3: SCC4
+                 - 4: SMC1
+                 - 5: SMC2
+              enum: [0, 1, 2, 3, 4, 5]
+        minItems: 1
+        maxItems: 64
+
+    allOf:
+      # If fsl,common-rxtx-pins is present, only 2 clocks are needed.
+      # Else, the 4 clocks must be present.
+      - if:
+          required:
+            - fsl,common-rxtx-pins
+        then:
+          properties:
+            clocks:
+              maxItems: 2
+            clock-names:
+              maxItems: 2
+        else:
+          properties:
+            clocks:
+              minItems: 4
+            clock-names:
+              minItems: 4
+
+    required:
+      - reg
+      - clocks
+      - clock-names
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - '#address-cells'
+  - '#size-cells'
+  - '#fsl,serial-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/soc/fsl,tsa.h>
+
+    tsa@ae0 {
+        compatible = "fsl,mpc885-tsa", "fsl,cpm1-tsa";
+        reg = <0xae0 0x10>,
+              <0xc00 0x200>;
+        reg-names = "si_regs", "si_ram";
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+        #fsl,serial-cells = <1>;
+
+        tdm@0 {
+            /* TDMa */
+            reg = <0>;
+
+            clocks = <&clk_l1rsynca>, <&clk_l1rclka>;
+            clock-names = "l1rsync", "l1rclk";
+
+            fsl,common-rxtx-pins;
+            fsl,fsync-rising-edge;
+
+            fsl,tx-ts-routes = < 2 0 >,             /* TS 0..1 */
+                           < 24 FSL_CPM_TSA_SCC4 >, /* TS 2..25 */
+                           < 1 0 >,                 /* TS 26 */
+                           < 5 FSL_CPM_TSA_SCC3 >;  /* TS 27..31 */
+
+            fsl,rx-ts-routes = < 2 0 >,             /* TS 0..1 */
+                           < 24 FSL_CPM_TSA_SCC4 >, /* 2..25 */
+                           < 1 0 >,                 /* TS 26 */
+                           < 5 FSL_CPM_TSA_SCC3 >;  /* TS 27..31 */
+        };
+    };

@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
+
+#ifndef __DT_BINDINGS_SOC_FSL_TSA_H
+#define __DT_BINDINGS_SOC_FSL_TSA_H
+
+#define FSL_CPM_TSA_NU		0	/* Pseuso Cell Id for not used item */
+#define FSL_CPM_TSA_SCC2	1
+#define FSL_CPM_TSA_SCC3	2
+#define FSL_CPM_TSA_SCC4	3
+#define FSL_CPM_TSA_SMC1	4
+#define FSL_CPM_TSA_SMC2	5
+
+#endif