On Tue, Jan 29, 2019 at 2:09 AM Mathias Thore
[off-list ref] wrote:

Is there a scenario where we are clearing the TX ring but don't want to reset the BQL TX queue?

Right now the function is also used on interface open/close, driver
removal and driver resumption besides the timeout situation. I think
the reseting BQL queue is either not neccessary or already called
explicitly for the other scenarios.

I think it makes sense to keep it in ucc_geth_free_tx since the reason it is needed isn't the timeout per se, but rather the clearing of the TX ring. This way, it will be performed no matter why the driver ends up calling this function.

I don't see a consensus on when netdev_reset_queue() should be called
among existing drivers.  Doing it on buffer ring cleanup probably can
be future-proofing.  But if we want to use this approach, we can
remove the redundent netdev_reset_queue() calls in open/close
functions.

Regards,
Leo

-----Original Message-----
From: Li Yang [mailto:leoyang.li@nxp.com]
Sent: Monday, 28 January 2019 22:37
To: Mathias Thore <redacted>
Cc: Christophe Leroy <redacted>; netdev@vger.kernel.org; linuxppc-dev@lists.ozlabs.org; David Gounaris <redacted>; Joakim Tjernlund <redacted>
Subject: Re: [PATCH] ucc_geth: Reset BQL queue when stopping device

On Mon, Jan 28, 2019 at 8:37 AM Mathias Thore [off-list ref] wrote:

quoted

Hi,


This is what we observed: there was a storm on the medium so that our controller could not do its TX, resulting in timeout. When timeout occurs, the driver clears all descriptors from the TX queue. The function called in this patch is used to reflect this clearing also in the BQL layer. Without it, the controller would get stuck, unable to perform TX, even several minutes after the storm had ended. Bringing the device down and then up again would solve the problem, but this patch also solves it automatically.

The explanation makes sense.  So this should only be required in the timeout scenario instead of other clean up scenarios like device shutdown?  If so, it probably it will be better to be done in ucc_geth_timeout_work()?

quoted

Some other drivers do the same, for example e1000e driver calls netdev_reset_queue in its e1000_clean_tx_ring function. It is possible that other drivers should do the same; I have no way of verifying this.


Regards,

Mathias

--


From: Christophe Leroy <redacted>
Sent: Monday, January 28, 2019 10:48 AM
To: Mathias Thore; leoyang.li@nxp.com; netdev@vger.kernel.org;
linuxppc-dev@lists.ozlabs.org; David Gounaris; Joakim Tjernlund
Subject: Re: [PATCH] ucc_geth: Reset BQL queue when stopping device


CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe.


Hi,

Le 28/01/2019 à 10:07, Mathias Thore a écrit :

quoted

After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.

What are the symptomns ?

Is this reset needed on any network driver in that case, or is it
something particular for the ucc_geth ?
For instance, the freescale fs_enet doesn't have that reset. Should it
have it too ?

Christophe

quoted

Co-authored-by: David Gounaris [off-list ref]
Signed-off-by: Mathias Thore <redacted>
---
  drivers/net/ethernet/freescale/ucc_geth.c | 2 ++
  1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/freescale/ucc_geth.c

b/drivers/net/ethernet/freescale/ucc_geth.c
index c3d539e209ed..eb3e65e8868f 100644

--- a/drivers/net/ethernet/freescale/ucc_geth.c
+++ b/drivers/net/ethernet/freescale/ucc_geth.c

@@ -1879,6 +1879,8 @@ static void ucc_geth_free_tx(struct ucc_geth_private *ugeth)
      u16 i, j;
      u8 __iomem *bd;

+     netdev_reset_queue(ugeth->ndev);
+
      ug_info = ugeth->ug_info;
      uf_info = &ug_info->uf_info;