[PATCH] dt-bindings: powerpc: adapt mpc5121-psc document to reality
From: Uwe Kleine-König <hidden>
Date: 2015-07-16 19:35:28
Also in:
linux-devicetree, linux-spi
Subsystem:
linux for powerpc (32-bit and 64-bit), linux for powerpc embedded ppc85xx, open firmware and flattened device tree bindings, the rest · Maintainers:
Madhavan Srinivasan, Scott Wood, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
The drivers support MPC5125 additionally to MPC5121, and there is an spi mode that is also supported. Additionally some minor corrections are done. Signed-off-by: Uwe Kleine-König <redacted> --- Hello, I sent a patch adding mpc5125 support to the mpc512x driver and Mark requested the new compatible to be documented. While at it I updated the document a bit more, and obviously the spi support for mpc5125 depends on my patch that isn't mainline yet. Best regards Uwe .../bindings/powerpc/fsl/mpc5121-psc.txt | 24 ++++++++++++++++------ 1 file changed, 18 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt
index 8832e8798912..647817527c88 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt@@ -6,14 +6,14 @@ PSC in UART mode For PSC in UART mode the needed PSC serial devices are specified by fsl,mpc5121-psc-uart nodes in the fsl,mpc5121-immr SoC node. Additionally the PSC FIFO -Controller node fsl,mpc5121-psc-fifo is requered there: +Controller node fsl,mpc5121-psc-fifo is required there: -fsl,mpc5121-psc-uart nodes +fsl,mpc512x-psc-uart nodes -------------------------- Required properties : - - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" - - cell-index : Index of the PSC in hardware + - compatible : Should contain "fsl,<soc>-psc-uart" and "fsl,<soc>-psc" + Supported <soc>s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC device - interrupts : <a b> where a is the interrupt number of the PSC FIFO Controller and b is a field that represents an
@@ -25,12 +25,21 @@ Recommended properties : - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) +PSC in SPI mode +--------------- -fsl,mpc5121-psc-fifo node +Similar to the UART mode a PSC can be operated in SPI mode. The compatible used +for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well. +The required and recommended properties are identical to the +fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible +string. + +fsl,mpc512x-psc-fifo node ------------------------- Required properties : - - compatible : Should be "fsl,mpc5121-psc-fifo" + - compatible : Should be "fsl,<soc>-psc-fifo" + Supported <soc>s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC FIFO Controller - interrupts : <a b> where a is the interrupt number of the
@@ -39,6 +48,9 @@ Required properties : - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +Recommended properties : + - clocks : specifies the clock needed to operate the fifo controller + - clock-names : name(s) for the clock(s) listed in clocks Example for a board using PSC0 and PSC1 devices in serial mode:
--
2.1.4