Re: [PATCH 2/2 V3] powerpc/85xx: add the P1020RDB-PD DTS support

On 07/09/2013 03:35:43 AM, Haijun Zhang wrote:

Overview of P1020RDB-PD device:
- DDR3 2GB
- NOR flash 64MB
- NAND flash 128MB
- SPI flash 16MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe
=20
Signed-off-by: Haijun Zhang <redacted>
Signed-off-by: Jerry Huang <redacted>
Signed-off-by: Xie Xiaobo-R63061 <redacted>
CC: Scott Wood <redacted>
---
changes for v3:
	- Remove some blank and changed the usb node
	- Renamed the dts file
	- change the cpld name of pd board
=20
 arch/powerpc/boot/dts/p1020rdb-pd.dts  |  90 ++++++++++++
 arch/powerpc/boot/dts/p1020rdb-pd.dtsi | 257 =20
+++++++++++++++++++++++++++++++++
 2 files changed, 347 insertions(+)
 create mode 100644 arch/powerpc/boot/dts/p1020rdb-pd.dts
 create mode 100644 arch/powerpc/boot/dts/p1020rdb-pd.dtsi

Again, why do you need a separate .dtsi?  If this isn't for a 32/36-bit =20
split, what is the criteria for what goes in the .dts versus what goes =20
in the .dtsi?

+		partition@600000 {
+			/* 4MB for Compressed Root file System Image */
+			reg =3D <0x00600000 0x00400000>;
+			label =3D "NAND Compressed RFS Image";
+		};
+
+		partition@a00000 {
+			/* 22MB for JFFS2 based Root file System */
+			reg =3D <0x00a00000 0x01600000>;
+			label =3D "NAND JFFS2 Root File System";
+		};

Don't refer to JFFS2.  It's bad enough that we specify partition layout =20
here -- no need to specify the filesystem type, especially when it's a =20
fs type that is no longer recommended.

+		partition@2000000 {
+			/* 96MB for RAMDISK based Root file System */
+			reg =3D <0x02000000 0x06000000>;
+			label =3D "NAND Writable User area";
+		};

Wouldn't it be better to combine these last three partitions?  Why do =20
you need three root filesystems?

+	cpld@2,0 {
+		compatible =3D "fsl,p1020rdb-pd-cpld";
+		reg =3D <0x2 0x0 0x20000>;
+		read-only;
+	};

Remove read-only.

+	spi@7000 {
+		flash@0 {
+			#address-cells =3D <1>;
+			#size-cells =3D <1>;
+			compatible =3D "spansion,s25sl12801";
+			reg =3D <0>;
+			spi-max-frequency =3D <40000000>; /* input clock =20
*/
+
+			partition@u-boot {
+				/* 512KB for u-boot Bootloader Image */
+				reg =3D <0x0 0x00080000>;
+				label =3D "u-boot";
+				read-only;
+			};
+
+			partition@dtb {
+				/* 512KB for DTB Image*/
+				reg =3D <0x00080000 0x00080000>;
+				label =3D "dtb";
+			};
+
+			partition@kernel {
+				/* 4MB for Linux Kernel Image */
+				reg =3D <0x00100000 0x00400000>;
+				label =3D "kernel";
+			};

These unit addresses are not appropriate.  They should match reg, not =20
label.

+			partition@fs {
+				/* 4MB for Compressed RFS Image */
+				reg =3D <0x00500000 0x00400000>;
+				label =3D "file system";
+			};
+
+			partition@jffs-fs {
+				/* 7MB for JFFS2 based RFS */
+				reg =3D <0x00900000 0x00700000>;
+				label =3D "file system jffs2";
+			};

As with NAND flash, please combine these and don't reference JFFS2.

+		};
+
+		slic@0 {
+			compatible =3D "zarlink,le88266";
+			reg =3D <1>;
+			spi-max-frequency =3D <8000000>;
+		};
+
+		slic@1 {
+			compatible =3D "zarlink,le88266";
+			reg =3D <2>;
+			spi-max-frequency =3D <8000000>;
+		};
+	};
+
+	mdio@24000 {
+		phy0: ethernet-phy@0 {
+			interrupts =3D <3 1 0 0>;
+			reg =3D <0x0>;
+		};
+		phy1: ethernet-phy@1 {
+			interrupts =3D <2 1 0 0>;
+			reg =3D <0x1>;
+		};
+	};

Again, leave a blank line between nodes.  If I comment about a style =20
issue in one place, you should also fix the same issue in other places =20
where it occurs.

+	/*
+	 * USB2 is shared with localbus, so it must be disabled
+	 * by default. We can't put 'status =3D "disabled";' here
+	 * since U-Boot doesn't clear the status property when
+	 * it enables USB2. OTOH, U-Boot does create a new node
+	 * when there isn't any. So, just comment it out.
+	 * usb@23000 {
+	 * 	status =3D "disabled";
+	 * 	phy_type =3D "ulpi";
+	 * };
+	 */

No.  Fix U-Boot to do whatever updating it needs to do based on runtime =20
configuration.  Do not add commented out nodes to the tree.

-Scott=