Re: kernel boot stuck at udbg_putc_cpm()

For some reason. This email was rejected. Resending...

On Sun, Jul 11, 2010 at 11:26 PM, Shawn Jin [off-list ref] wrote:

You're probably getting to the point where udbg is disabled because the
real serial driver is trying to take over -- and something's going
wrong with the real serial port driver. =A0Check to make sure the brg
config is correct (both the input clock and the baud rate you're trying
to switch to). =A0Commenting out the call to cpm_set_brg can be
a quick way of determining if that's the problem.

It seems that the last CP command RESTART_TX never completes in the
cpm_uart_console_setup(). I commented out the writes to brgc1 in
cpm_setbrg() in cpm1.c so that the brgc1 value stays the same as
previously set.

The registers related to SMC1 are dumped below before the last
RESTART_TX command. The CPCR was 0x0090. But after issuing the
RESTART_TX command the CPCR kept at 0x0691. Is there any other obvious
reason for CPM not completing the command? It got to be something
related to the settings.

BDI>rd cpcr
cpcr =A0 =A0 =A0 =A0 =A0 : 0x0090 =A0 =A0 =A0144
BDI>rd rccr
rccr =A0 =A0 =A0 =A0 =A0 : 0x0001 =A0 =A0 =A01
BDI>rd rmds
rmds =A0 =A0 =A0 =A0 =A0 : 0x00 =A0 =A0 =A0 =A00
BDI>rd rctr1
rctr1 =A0 =A0 =A0 =A0 =A0: 0x0000 =A0 =A0 =A00
BDI>rd rctr2
rctr2 =A0 =A0 =A0 =A0 =A0: 0x0000 =A0 =A0 =A00
BDI>rd rctr3
rctr3 =A0 =A0 =A0 =A0 =A0: 0x802e =A0 =A0 =A0-32722
BDI>rd rctr4
rctr4 =A0 =A0 =A0 =A0 =A0: 0x802c =A0 =A0 =A0-32724
BDI>rd rter
rter =A0 =A0 =A0 =A0 =A0 : 0x0000 =A0 =A0 =A00
BDI>rd rtmr
rtmr =A0 =A0 =A0 =A0 =A0 : 0x0000 =A0 =A0 =A00
BDI>rd brgc1
brgc1 =A0 =A0 =A0 =A0 =A0: 0x00010618 =A067096
BDI>rd smcmr1
smcmr1 =A0 =A0 =A0 =A0 : 0x4823 =A0 =A0 =A018467
BDI>rd smce1
smce1 =A0 =A0 =A0 =A0 =A0: 0x00 =A0 =A0 =A0 =A00
BDI>rd smcm1
smcm1 =A0 =A0 =A0 =A0 =A0: 0x00 =A0 =A0 =A0 =A00

Thanks,
-Shawn.