Re: [QUESTION] 440EPx with PCI to PCIe bridge error
From: Steven A. Falco <hidden>
Date: 2009-01-06 14:44:26
Benjamin Herrenschmidt wrote:
quoted
Here is a complete startup log, with debug turned on as you requested. This is still against 2.6.27.9, as it will take me a little time to build 2.6.28. Hopefully, this log will be useful in the meantime.Can you add "debug" to your kernel command line option or send the output of the "dmesg" command please ?
Here is the output of dmesg:
$ dmesg
Using Hydra_temp machine description
Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009
Found initrd at 0xcfcb7000:0xcff0b885
Found legacy serial port 0 for /plb/opb/serial@ef600300
mem=1ef600300, taddr=1ef600300, irq=0, clk=11059200, speed=115200
Found legacy serial port 1 for /plb/opb/serial@ef600400
mem=1ef600400, taddr=1ef600400, irq=0, clk=11059200, speed=0
Found legacy serial port 2 for /plb/opb/serial@ef600500
mem=1ef600500, taddr=1ef600500, irq=0, clk=11059200, speed=0
Found legacy serial port 3 for /plb/opb/serial@ef600600
mem=1ef600600, taddr=1ef600600, irq=0, clk=11059200, speed=0
console [udbg0] enabled
Top of RAM: 0xffff000, Total RAM: 0xffff000
Memory hole size: 0MB
Zone PFN ranges:
DMA 0x00000000 -> 0x0000ffff
Normal 0x0000ffff -> 0x0000ffff
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x0000ffff
On node 0 totalpages: 65535
free_area_init_node: node 0, pgdat c03522f0, node_mem_map c040f000
DMA zone: 65023 pages, LIFO batch:15
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65023
Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
PID hash table entries: 1024 (order: 10, 4096 bytes)
time_init: decrementer frequency = 666.666660 MHz
time_init: processor frequency = 666.666660 MHz
clocksource: timebase mult[600000] shift[22] registered
clockevent: decrementer mult[aaaa] shift[16] cpu[0]
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
net_namespace: 288 bytes
NET: Registered protocol family 16
PCI host bridge /plb/pci@1ec000000 (primary) ranges:
MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000
IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCI: Probing PCI hardware
PCI: 0000:00:00.0 reg 14 32bit mmio: [0, 7fffffff]
PCI:0000:00:00.0 Resource 1 0000000000000000-000000007fffffff [21208] is unassigned
PCI: Hiding 4xx host bridge resources 0000:00:00.0
pci 0000:00:00.0: supports D1
pci 0000:00:0c.0: supports D1
pci 0000:00:0c.0: PME# supported from D0 D1 D3hot
pci 0000:00:0c.0: PME# disabled
PCI: Fixup bus 0 (PHB)
Try to map irq for 0000:00:00.0...
pci_busdev_to_OF_node(0,0x0)
parent is /plb/pci@1ec000000
result is <NULL>
-> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
-> mapped to linux irq 16
Try to map irq for 0000:00:0c.0...
pci_busdev_to_OF_node(0,0x60)
parent is /plb/pci@1ec000000
result is <NULL>
-> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
-> mapped to linux irq 16
PCI: 0000:01:00.0 reg 10 32bit mmio: [80000000, 8007ffff]
PCI: 0000:01:00.0 reg 14 32bit mmio: [f0000000, ffffffff]
PCI:0000:01:00.0 Resource 0 0000000080000000-000000008007ffff [20200] fixup...
PCI:0000:01:00.0 0000000180000000-000000018007ffff
PCI:0000:01:00.0 Resource 1 00000000f0000000-00000000ffffffff [20200] fixup...
PCI:0000:01:00.0 00000001f0000000-00000001ffffffff
PCI: bridge 0000:00:0c.0 32bit mmio: [80000000, 800fffff]
PCI: Fixup bus 1 (0000:00:0c.0)
PCI:0000:00:0c.0 Bus rsrc 1 0000000080000000-00000000800fffff [200] fixup...
PCI:0000:00:0c.0 0000000180000000-00000001800fffff
Try to map irq for 0000:01:00.0...
pci_busdev_to_OF_node(1,0x0)
pci_busdev_to_OF_node(0,0x60)
parent is /plb/pci@1ec000000
result is <NULL>
-> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2
-> mapped to linux irq 16
PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO)
PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem)
PCI: Assigning unassigned resouces...
pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff]
pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff]
pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff]
pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:0c.0: IO window: disabled
pci 0000:00:0c.0: MEM window: disabled
pci 0000:00:0c.0: PREFETCH window: disabled
bus: 00 index 0 io port: [0, fffff]
bus: 00 index 1 mmio: [180000000, 18fffffff]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [0, 0]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 mmio: [0, 0]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 2386k freed
msgmni has been set to 500
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
console handover: boot [udbg0] -> real [ttyS0]
serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A
1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A
1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A
1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support
/plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0
eth0: found Marvell 88E1111 Ethernet PHY (0x00)
/plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1
eth1: found Marvell 88E1111 Ethernet PHY (0x01)
Uniform Multi-Platform E-IDE driver
Driver 'sd' needs updating - please use bus_type methods
scsi0 : pata_platform
ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32
ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2
ata1.00: 2001888 sectors, multi 0: LBA
ata1.00: configured for PIO
ata1.00: configured for PIO
ata1: EH complete
scsi 0:0:0:0: Direct-Access ATA SMC01GBFK6E CF08 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 9 MTD partitions on "1fc000000.nor_flash":
0x00000000-0x00500000 : "kernel0"
0x00500000-0x00a00000 : "ramdisk0"
0x00a00000-0x00f00000 : "kernel1"
0x00f00000-0x01400000 : "ramdisk1"
0x01400000-0x01900000 : "kernel2"
0x01900000-0x01e00000 : "ramdisk2"
0x03f60000-0x03f80000 : "env0"
0x03f80000-0x03fa0000 : "env1"
0x03fa0000-0x04000000 : "u-boot"
spi_ppc4xx_of 1ef600900.spi: driver initialized
ppc-of-ehci e0000300.ehci: OF EHCI
ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1
ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300
ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OF EHCI
usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd
usb usb1: SerialNumber: PPC-OF USB
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-of-ohci e0000400.usb: OF OHCI
ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2
ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OF OHCI
usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd
usb usb2: SerialNumber: PPC-OF USB
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0
ibm-iic 1ef600700.i2c: using standard (100 kHz) mode
ibm-iic 1ef600800.i2c: using standard (100 kHz) mode
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ad7414 0-0048: chip found
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218)
eth0: link is down
eth0: link is up, 100 FDX, pause enabled
IP-Config: Complete:
device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1,
host=hydra_temp, domain=, nis-domain=(none),
bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath=
Freeing unused kernel memory: 156k init
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
$
Cheers, Ben.quoted
Steve U-Boot 2008.10-00079-gebb3412 (Dec 9 2008 - 16:06:05) CPU: AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz) Security/Kasumi support Bootstrap Option H - Boot ROM Location I2C (Addr 0x52) Internal PCI arbiter enabled, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# 7654 I2C: ready SPI: ready DTT: 1 is 27 C DRAM: 256 MB FLASH: 64 MB NAND: 32 MiB PCI: Bus Dev VenId DevId Class Int 01 00 1172 0004 ff00 43 00 0c 10b5 8112 0604 43 In: serial Out: serial Err: serial RTC: ready USB: Host(int phy) Device(ext phy) Net: ppc_4xx_eth0, ppc_4xx_eth1 IDE: Bus 0: OK Device 0: PIO mode 4 Model: SMC01GBFK6E Firm: CF080204 Ser#: NU0B4000000000102893 Type: Hard Disk Capacity: 977.4 MB = 0.9 GB (2001888 x 512) ========================================================== | | | Welcome to Hydra | | | ========================================================== Please type "sm" to enter safe-mode. Starting current kernel - please wait. Starting previous kernel - please wait. Starting safe-mode kernel - please wait. ## Booting kernel from Legacy Image at fd400000 ... Image Name: Linux-2.6.27.9-00045-gcccf182-di Created: 2009-01-05 21:29:41 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1684167 Bytes = 1.6 MB Load Address: 00400000 Entry Point: 00400454 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at fd900000 ... Image Name: initramfs Created: 2008-11-26 15:13:12 UTC Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 2443397 Bytes = 2.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK CPU clock-frequency <- 0x27bc86a4 (667MHz) CPU timebase-frequency <- 0x27bc86a4 (667MHz) /plb: clock-frequency <- 9ef21a9 (167MHz) /plb/opb: clock-frequency <- 4f790d4 (83MHz) /plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz) /plb/opb/serial@ef600300: clock-frequency <- a8c000 (11MHz) /plb/opb/serial@ef600400: clock-frequency <- a8c000 (11MHz) /plb/opb/serial@ef600500: clock-frequency <- a8c000 (11MHz) /plb/opb/serial@ef600600: clock-frequency <- a8c000 (11MHz) Memory <- <0x0 0x0 0xffff000> (255MB) ENET0: local-mac-address <- 00:10:ec:01:04:d0 ENET1: local-mac-address <- 00:10:ec:01:04:d1 zImage starting: loaded at 0x00400000 (sp: 0x0ff0c300) Allocating 0x371974 bytes for kernel ... gunzipping (0x00000000 <- 0x0040f000:0x007ac72c)...done 0x35a1e4 bytes Using loader supplied ramdisk at 0xfcb7000-0xff0b885 initrd head: 0x1f8b0808 Linux/PowerPC load: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200 Finalizing device tree... flat tree at 0x40bf08 Using Hydra_temp machine description Linux version 2.6.27.9-00045-gcccf182-dirty (sfalco@saf.cs.myharris.net) (gcc version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009 Found initrd at 0xcfcb7000:0xcff0b885 console [udbg0] enabled setup_arch: bootmem arch: exit Zone PFN ranges: DMA 0x00000000 -> 0x0000ffff Normal 0x0000ffff -> 0x0000ffff Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x0000ffff Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65023 Kernel command line: root=/dev/sda3 rw ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off panic=1 console=ttyS0,115200 UIC0 (32 IRQ sources) at DCR 0xc0 UIC1 (32 IRQ sources) at DCR 0xd0 UIC2 (32 IRQ sources) at DCR 0xe0 PID hash table entries: 1024 (order: 10, 4096 bytes) clocksource: timebase mult[600000] shift[22] registered Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k data, 90k bss, 156k init) SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400) Mount-cache hash table entries: 512 net_namespace: 288 bytes NET: Registered protocol family 16 PCI host bridge /plb/pci@1ec000000 (primary) ranges: MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000 IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000 4xx PCI DMA offset set to 0x00000000 PCI: Probing PCI hardware PCI: Hiding 4xx host bridge resources 0000:00:00.0 pci 0000:00:0c.0: PME# supported from D0 D1 D3hot pci 0000:00:0c.0: PME# disabled Try to map irq for 0000:00:00.0... pci_busdev_to_OF_node(0,0x0) parent is /plb/pci@1ec000000 result is <NULL> -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 -> mapped to linux irq 16 Try to map irq for 0000:00:0c.0... pci_busdev_to_OF_node(0,0x60) parent is /plb/pci@1ec000000 result is <NULL> -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 -> mapped to linux irq 16 Try to map irq for 0000:01:00.0... pci_busdev_to_OF_node(1,0x0) pci_busdev_to_OF_node(0,0x60) parent is /plb/pci@1ec000000 result is <NULL> -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 -> mapped to linux irq 16 PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], parent c0339b40 (PCI IO) PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], parent c0339b18 (PCI mem) PCI: Assigning unassigned resouces... pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff] pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff] pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01 pci 0000:00:0c.0: IO window: disabled pci 0000:00:0c.0: MEM window: disabled pci 0000:00:0c.0: PREFETCH window: disabled bus: 00 index 0 io port: [0, fffff] bus: 00 index 1 mmio: [180000000, 18fffffff] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [0, 0] bus: 01 index 2 mmio: [0, 0] bus: 01 index 3 mmio: [0, 0] SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 2386k freed msgmni has been set to 500 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A console handover: boot [udbg0] -> real [ttyS0] serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A 1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A 1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A 1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A 1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A brd: module loaded PPC 4xx OCP EMAC driver, version 3.54 MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels ZMII /plb/opb/emac-zmii@ef600d00 initialized RGMII /plb/opb/emac-rgmii@ef601000 initialized with MDIO support /plb/opb/emac-rgmii@ef601000: input 0 in RGMII mode eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:01:04:d0 eth0: found Marvell 88E1111 Ethernet PHY (0x00) /plb/opb/emac-rgmii@ef601000: input 1 in RGMII mode eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:01:04:d1 eth1: found Marvell 88E1111 Ethernet PHY (0x01) Uniform Multi-Platform E-IDE driver Driver 'sd' needs updating - please use bus_type methods scsi0 : pata_platform ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32 ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2 ata1.00: 2001888 sectors, multi 0: LBA ata1.00: configured for PIO ata1.00: configured for PIO ata1: EH complete scsi 0:0:0:0: Direct-Access ATA SMC01GBFK6E CF08 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Creating 9 MTD partitions on "1fc000000.nor_flash": 0x00000000-0x00500000 : "kernel0" 0x00500000-0x00a00000 : "ramdisk0" 0x00a00000-0x00f00000 : "kernel1" 0x00f00000-0x01400000 : "ramdisk1" 0x01400000-0x01900000 : "kernel2" 0x01900000-0x01e00000 : "ramdisk2" 0x03f60000-0x03f80000 : "env0" 0x03f80000-0x03fa0000 : "env1" 0x03fa0000-0x04000000 : "u-boot" spi_ppc4xx_of 1ef600900.spi: driver initialized ppc-of-ehci e0000300.ehci: OF EHCI ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1 ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300 ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OF EHCI usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd usb usb1: SerialNumber: PPC-OF USB ppc-of-ohci e0000400.usb: OF OHCI ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2 ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OF OHCI usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd usb usb2: SerialNumber: PPC-OF USB Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver rtc-m41t80 0-0068: chip found, driver version 0.05 rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0 ibm-iic 1ef600700.i2c: using standard (100 kHz) mode ibm-iic 1ef600800.i2c: using standard (100 kHz) mode at24 0-0052: 512 byte 24c04 EEPROM (writable) ad7414 0-0048: chip found TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC (1231155218) eth0: link is down eth0: link is up, 100 FDX, pause enabled IP-Config: Complete: device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1, host=hydra_temp, domain=, nis-domain=(none), bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath= Freeing unused kernel memory: 156k init Checking /dev/sda1 Checking /dev/sda2 Checking /dev/sda3 Checking /dev/sda4 kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT) starting pid 889, tty '/dev/ttyS0': '/etc/init.d/rcS' launcher[944]: launching /bin/craft on /dev/ttyS0 Hydra>