Hi Ben,
On Thu, Mar 06, 2008 at 10:46:51AM +1100, Benjamin Herrenschmidt wrote:
quoted
quoted
quoted
From your .dts, I see you've been doing some swizzling of slots using
interrupts 1...4 ... do that correspond to EXTIRQ 5....8 ?
No, those correspond to the EXT1-4 that are the other side of the #ifdef
for this board in arch/ppc. :-)
Yes, that's what I was thinking. So that's what he got wrong in
his .dts.
Philippe, you need to fix those numbers so they map your EXTIRQ.
(that is 1 -> 5, 2 -> 6, etc... )
And of course you need to make sure you have the right routing to the
chip. it's funny the way you keep providing all sort of info but -never-
the one we actually asked for :-)
I did not have that. The board has been designed, and the original linux
port has been made, by a third-party, and the documentation is scarce :(
We basically, to help you, need to know for each PCI device connected to
the SoC, or PCI slot if you have such, which address line is used for
IDSEL, and to which MPIC interrupt inputs.
Well, i have finally an answer for IDSEL : it is connected to AD18 (18 is
decimal), but we knew that actually, because the chip appears as 0000:00:12.0,
0000:00:12.1 and 0000:00:12.2 in the kernel messages.
The pci4520 chip does not have pins labelled inta, intb, intc, or intd,
but pins labelled mfunc0, mfunc1 ... mfunc6.
The pci4520 datasheet does not seem very clear to me about the relation
between the mfunc0..6 pins and the inta..d interrupts :(
Luckily, the running linux kernel shows in /proc/interrupts :
55: 18797 OpenPIC Level yenta, ide0
54: 1 OpenPIC Level yenta
55: 79 OpenPIC Level ohci1394
I can thus deduce that each function of the pci4520 chip uses only
one interrupt line. With the kernel messages at startup, I also
know that the two yenta's are 12.0 and 12.1 and the ohci1394 is 12.2.
I wrote then the following in my dts file :
pci@e0008000 {
/*
f800 masks idsel address line
07 masks (sub)function number
7 masks INTA, INTB, INTC or INTD
*/
interrupt-map-mask = <ff00 0 0 7>;
interrupt-map = <
/* IDSEL 0x12 func 0 */
9000 0 0 1 &mpic 5 1
9000 0 0 2 &mpic 5 1
9000 0 0 3 &mpic 5 1
9000 0 0 4 &mpic 5 1
/* IDSEL 0x12 func 1 */
9100 0 0 1 &mpic 6 1
9100 0 0 2 &mpic 6 1
9100 0 0 3 &mpic 6 1
9100 0 0 4 &mpic 6 1
27 more lines
Once you have given us that, we'll be able to help.
It appears that just looking at the arch/ppc code is a bit too messy and
confusing (and not necessarily right).
In addition, you will also need to do proper interrupt routing for you
other devices (RTC, etc...) but we can look at that separately.
That's for tomorrow.
But I already noticed that the interrupt numbers that the arch/powerpc tree
uses for the parts that do already work (compact-flash and serials) are
different from the ones I saw on the running arch/ppc tree. e.g.,
the serial lines used irq 26 with the arch/ppc tree and now use 42 with
the powerpc tree. For the pci4520, irqs changed from 53, 54 and 55 in the
arch/ppc kernel to 17, 18 and 19 with the arch/powerpc kernel.
That's a little bit confusing.
There must be something hidden in the sources of the openpic driver to
explain that difference. Could it be fixed by a setting in the dts-file ?
Thanks for you help
Philippe