Xilinx Virtex boot

6 messages, 3 authors, 2007-08-30 · open the first message on its own page

Xilinx Virtex boot

From: Robert Woodworth <hidden>
Date: 2007-08-29 23:35:01 

I'm trying to port Linux to a new Virtex Platform.  The kernel will not
uncompress, I get the following on the console:



loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=ttyUL root=/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit



Any ideas what causes this error??
Is something mis-configured on my EDK project?


I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??



Rob.

Re: Xilinx Virtex boot

From: Grant Likely <hidden>
Date: 2007-08-30 00:29:03 

On 8/29/07, Robert Woodworth [off-list ref] wrote:
I'm trying to port Linux to a new Virtex Platform.  The kernel will not
uncompress, I get the following on the console:

loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=ttyUL root=/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit

Any ideas what causes this error??
Is something mis-configured on my EDK project?
Possibly, do you know that EDK has your ram is configured correctly
(ie. have you run a memory test application)?

I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??
It shouldn't be the problem, but why are you doing that?

Cheers,
g.

-- 
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
grant.likely@secretlab.ca
(403) 399-0195

Re: Xilinx Virtex boot

From: Robert Woodworth <hidden>
Date: 2007-08-30 14:44:41 

On Wed, 2007-08-29 at 18:29 -0600, Grant Likely wrote:
On 8/29/07, Robert Woodworth [off-list ref] wrote:
quoted
I'm trying to port Linux to a new Virtex Platform.  The kernel will not
uncompress, I get the following on the console:

loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=ttyUL root=/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit

Any ideas what causes this error??
Is something mis-configured on my EDK project?
Possibly, do you know that EDK has your ram is configured correctly
(ie. have you run a memory test application)?
Yes, I ran the sample memory test application that EDK builds
automatically.  It ran fine.

The fact that the above prints on the console, tells me that the
zImage.elf is getting loaded at the correct start location and that its
partly executing.

What is the return code that I'm seeing??  I have been unable to figure
that out from the source yet.
quoted
I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??
It shouldn't be the problem, but why are you doing that?
We are building an image-processing application inside the FPGA.  The
application is very memory intensive.  I have been told that the PPC
always has priority on the PLB and that if I want to have my FPGA module
have priority on memory, that I should place the memory and my FPGA
module on the OPB.  Yes, this can significantly slow down the PPC, but
in my case the PPC is only used for UI and networking.

I will actually build in *two* OPBs one for the memory + my module and
the second for the other peripherals. 


Woody.

Re: Xilinx Virtex boot

From: Robert Woodworth <hidden>
Date: 2007-08-30 14:50:44 

On Wed, 2007-08-29 at 18:29 -0600, Grant Likely wrote:
On 8/29/07, Robert Woodworth [off-list ref] wrote:
quoted
I'm trying to port Linux to a new Virtex Platform.  The kernel will not
uncompress, I get the following on the console:

loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=ttyUL root=/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit

Any ideas what causes this error??
Is something mis-configured on my EDK project?
Possibly, do you know that EDK has your ram is configured correctly
(ie. have you run a memory test application)?
quoted
I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??
It shouldn't be the problem, but why are you doing that?
I did notice in my configuration, that when the memory is on the PLB it
has an interrupt flag and when it's on the OPB it doesn't.  What is the
interrupt for?  DMA's?

Could Linux be doing a DMA in the uncompression where the lack of an
interrupt causes and error?

Re: Xilinx Virtex boot

From: Grant Likely <hidden>
Date: 2007-08-30 15:02:45 

On 8/30/07, Robert Woodworth [off-list ref] wrote:
On Wed, 2007-08-29 at 18:29 -0600, Grant Likely wrote:
quoted
On 8/29/07, Robert Woodworth [off-list ref] wrote:
quoted
I'm trying to port Linux to a new Virtex Platform.  The kernel will not
uncompress, I get the following on the console:

loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=ttyUL root=/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit

Any ideas what causes this error??
Is something mis-configured on my EDK project?
Possibly, do you know that EDK has your ram is configured correctly
(ie. have you run a memory test application)?
Yes, I ran the sample memory test application that EDK builds
automatically.  It ran fine.

The fact that the above prints on the console, tells me that the
zImage.elf is getting loaded at the correct start location and that its
partly executing.

What is the return code that I'm seeing??  I have been unable to figure
that out from the source yet.
IIRC, the return code is the result of the CRC calculation.  If it is
non-zero, then the CRC was incorrect.  That says to me that you've got
either memory or download issues.

I have seen corruption in the past when downloading zImages larger
than about 1.2MB over JTAG.
quoted
quoted
I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??
It shouldn't be the problem, but why are you doing that?
We are building an image-processing application inside the FPGA.  The
application is very memory intensive.  I have been told that the PPC
always has priority on the PLB and that if I want to have my FPGA module
have priority on memory, that I should place the memory and my FPGA
module on the OPB.  Yes, this can significantly slow down the PPC, but
in my case the PPC is only used for UI and networking.
<offtopic> You might want to take a look at the MPMC ipcore.  It
allows multiple PLBs to address a single memory region.</offtopic>

Cheers,
g.

-- 
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
grant.likely@secretlab.ca
(403) 399-0195

RE: Xilinx Virtex boot (And MPMC)

From: Stephen Neuendorffer <hidden>
Date: 2007-08-30 16:07:38 

The MPMC would almost certainly be a better option here...

Steve

-----Original Message-----
From:=20
linuxppc-embedded-bounces+stephen=3Dneuendorffer.name@ozlabs.org
=20
[mailto:linuxppc-embedded-bounces+stephen=3Dneuendorffer.name@oz
labs.org] On Behalf Of Robert Woodworth
Sent: Thursday, August 30, 2007 7:45 AM
To: Grant Likely
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: Xilinx Virtex boot
=20
On Wed, 2007-08-29 at 18:29 -0600, Grant Likely wrote:
quoted
On 8/29/07, Robert Woodworth [off-list ref] wrote:
quoted
I'm trying to port Linux to a new Virtex Platform.  The=20
kernel will not
quoted
quoted
uncompress, I get the following on the console:

loaded at:     00400000 004FB19C
board data at: 004F9120 004F919C
relocated to:  00404054 004040D0
zimage at:     00404E50 004F8409
avail ram:     004FC000 04000000

Linux/PPC load: console=3DttyUL root=3D/dev/xsa2
Uncompressing Linux...
zlib_inflateInit2 returned 00506530
exit

Any ideas what causes this error??
Is something mis-configured on my EDK project?
=20
Possibly, do you know that EDK has your ram is configured correctly
(ie. have you run a memory test application)?
=20
Yes, I ran the sample memory test application that EDK builds
automatically.  It ran fine.
=20
The fact that the above prints on the console, tells me that the
zImage.elf is getting loaded at the correct start location=20
and that its
partly executing.
=20
What is the return code that I'm seeing??  I have been unable=20
to figure
that out from the source yet.
=20
=20
quoted
quoted
I have 64MB DDR on the OPB *not* the PLB.
Is that a problem??
=20
It shouldn't be the problem, but why are you doing that?
=20
We are building an image-processing application inside the FPGA.  The
application is very memory intensive.  I have been told that the PPC
always has priority on the PLB and that if I want to have my=20
FPGA module
have priority on memory, that I should place the memory and my FPGA
module on the OPB.  Yes, this can significantly slow down the PPC, but
in my case the PPC is only used for UI and networking.
=20
I will actually build in *two* OPBs one for the memory + my module and
the second for the other peripherals.=20
=20
=20
Woody.
=20
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
=20
=20
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help