RE: ML403 gigabit ethernet bandwidth - 2.6 kernel

Use the following command in Linux please:

ifconfig eth0 mtu 8982

As well you should do that on your PC in the measurement.

Ming

From: Mohammad Sadegh Sadri <redacted>
To: Ming Liu <redacted>, 

[off-list ref],[off-list ref], 
[off-list ref]

Subject: RE: ML403 gigabit ethernet bandwidth - 2.6 kernel
Date: Sat, 23 Jun 2007 19:08:29 +0000


Dear Ming,

Really thanks for reply,

about thresholds and waitbound OK! I'll adjust them in adapter.c ,

but what about enabling jumbo frames? should I do any thing special to 

enable Jumbo fram support?

we were thinking that it is enabled by default. Is it?

thanks




----------------------------------------

quoted

From: eemingliu@hotmail.com
To: mamsadegh@hotmail.com; akonovalov@ru.mvista.com; 

linuxppc-embedded@ozlabs.org; grant.likely@secretlab.ca

quoted

Subject: RE: ML403 gigabit ethernet bandwidth - 2.6 kernel
Date: Sat, 23 Jun 2007 18:48:19 +0000

Dear Mohammad,
There are some parameters which could be adjusted to improve the
performance. They are: TX and RX_Threshold TX and RX_waitbound. In my
system, we use TX_Threshold=16 and Rx_Threshold=8 and both waitbound=1.

Also Jumbo frame of 8982 could be enable.

Try those hints and share your improvement with us.

BR
Ming

quoted

From: Mohammad Sadegh Sadri
To: Andrei Konovalov , Linux PPC Linux

PPC, Grant Likely

quoted

Subject: ML403 gigabit ethernet bandwidth - 2.6 kernel
Date: Sat, 23 Jun 2007 12:19:12 +0000


Dear all,

Recently we did a set of tests on performance of virtex 4FX hard TEMAC

module using ML403

quoted

we studied all of the posts here carefully: these are the system

characteristics;

quoted

Board : ML403
EDK    : EDK9.1SP2
Hard TEMAC version and PLTEMAC version are both 3.0.a
PPC clock frequency :  300MHz
Kernel : 2.6.21-rc7 , downloaded from grant's git tree some thing near 

one

quoted

week ago

quoted

DMA type: 3 (sg dma)
DRE : enabled for TX and RX, (2)
CSUM offload is enabled for both of TX and RX
tx and rx fifo sizes : 131072 bits

the board comes up over NFS root file system completely and without 

any

quoted

problems.

quoted

PC system used for these tests is : CPU P4 Dual Core, 3.4GHz , 

2Gigabytes

quoted

memory, Dual gigabit ethernet port, running linux 2.6.21.3

quoted

We have tested the PC system band width and it can easily reach 

966mbits/s

quoted

when connected to the same PC. ( using the same cross cable used for 

ml403

quoted

test)

quoted

Netperf is compiled with TCP SEND FILE enabled, ( -DHAVE_SENDFILE)

(from board to PC)
netperf -t TCP_SENDFILE -H 10.10.10.250 -F /boot/zImage.elf -- -m 

16384 -s

quoted

87380 -S 87380

quoted

the measured bandwidth for this test was just 40.66Mbits.
It is also true for netperf from PC to board.

we do not have any more idea about what we should do to improve the

bandwidth.

quoted

any help or ideas is appreciated...

_________________________________________________________________
Connect to the next generation of MSN

Messenger?>http://imagine-msn.com/messenger/launch80/default.aspx?locale=en-us&source=wlmailtagline

quoted

quoted

_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

_________________________________________________________________
免费下载 MSN Explorer:   http://explorer.msn.com/lccn/

_________________________________________________________________
News, entertainment and everything you care about at Live.com. Get it now!
http://www.live.com/getstarted.aspx

_________________________________________________________________
免费下载 MSN Explorer:   http://explorer.msn.com/lccn/