Hello all:
I would like to understand if there is a way to program the PCI interrupt pin register of MPC8540. I did look for this in the datasheet, but couldn't find any positive answer.
Currently, I am working in a set-up where MPC8540 is an agent, plugged into the PC host.
I couldn't get an IRQ for the card when plugged in some PCI slots, whereas in one of the slots I do see a non-zero value.
It would be great if you could help me understand the issue.
I am sorry if the question is inapporpriate in the group. I am desperate to solve the issue.
Thanks for any help.
J.Joseph
----- Original Message ----
From: Kumar Gala <redacted>
To: Wang Matthew-R59995 <redacted>
Cc: linuxppc-embedded@ozlabs.org
Sent: Wednesday, 18 October, 2006 6:54:24 PM
Subject: Re: Linuxppc-embedded Digest, Vol 26, Issue 36
On Oct 18, 2006, at 8:10 PM, Wang Matthew-R59995 wrote:
Hi Kumar,
Actually I do many trials about it. Vxwerks Bootrom is smaller than
U-Boot. The key difference between Bootrom and U-boot is that some
source code of Bootrom is invisible to the users.
Actually the rfi instruction which I point out is the first rfi
instruction of Linux PowerPC bringup.
Before that, it's TLB entry invalidation and temp TLB entry mapping.
I check MMU setting carefully before coming Linux Kernel.
I just want to know if other guys met similar scenario like me. I
don't
need the precise answer, just overall suggestion about it because I
understand that not everyone has the same bootloader of mine, that
bootloader is actually a customized bootloader.
I understand that, thus I was asking what exact problem you were
seeing to try and help.
Anyway thank you.
R9 point to LR register, mask the high 20 bit of r9 and send to r7,
and
then add 24, which means stride 6 instructions for rfi instruction
execution.
Of course, rfi can switch the TLB entry, both the previous TLB
entry and
the temp TLB entry point to the same physical address.
I've checked it.
I know what the code does, I wrote it :)
- kumar
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
__________________________________________________________
Yahoo! India Answers: Share what you know. Learn something new
http://in.answers.yahoo.com/
Is this the pin used for the external messaging?
On 1/16/07, agnel juni [off-list ref] wrote:
Hello all:
I would like to understand if there is a way to program the PCI interrupt
pin register of MPC8540. I did look for this in the datasheet, but couldn't
find any positive answer.
Currently, I am working in a set-up where MPC8540 is an agent, plugged into
the PC host.
I couldn't get an IRQ for the card when plugged in some PCI slots, whereas
in one of the slots I do see a non-zero value.
It would be great if you could help me understand the issue.
I am sorry if the question is inapporpriate in the group. I am desperate to
solve the issue.
Thanks for any help.
J.Joseph
----- Original Message ----
From: Kumar Gala <redacted>
To: Wang Matthew-R59995 <redacted>
Cc: linuxppc-embedded@ozlabs.org
Sent: Wednesday, 18 October, 2006 6:54:24 PM
Subject: Re: Linuxppc-embedded Digest, Vol 26, Issue 36
On Oct 18, 2006, at 8:10 PM, Wang Matthew-R59995 wrote:
quoted
Hi Kumar,
Actually I do many trials about it. Vxwerks Bootrom is smaller than
U-Boot. The key difference between Bootrom and U-boot is that some
source code of Bootrom is invisible to the users.
Actually the rfi instruction which I point out is the first rfi
instruction of Linux PowerPC bringup.
Before that, it's TLB entry invalidation and temp TLB entry mapping.
I check MMU setting carefully before coming Linux Kernel.
I just want to know if other guys met similar scenario like me. I
don't
need the precise answer, just overall suggestion about it because I
understand that not everyone has the same bootloader of mine, that
bootloader is actually a customized bootloader.
I understand that, thus I was asking what exact problem you were
seeing to try and help.
quoted
Anyway thank you.
R9 point to LR register, mask the high 20 bit of r9 and send to r7,
and
then add 24, which means stride 6 instructions for rfi instruction
execution.
Of course, rfi can switch the TLB entry, both the previous TLB
entry and
the temp TLB entry point to the same physical address.
I've checked it.
I know what the code does, I wrote it :)
- kumar
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
________________________________
Here's a new way to find what you're looking for - Yahoo! Answers
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
--
/*
* Steve Iribarne
* Software Engineer
* (aka Grunt)
*/
On Jan 16, 2007, at 5:20 PM, agnel juni wrote:
Hello all:
I would like to understand if there is a way to program the PCI =20
interrupt pin register of MPC8540. I did look for this in the =20
datasheet, but couldn't find any positive answer.
Currently, I am working in a set-up where MPC8540 is an agent, =20
plugged into the PC host.
I couldn't get an IRQ for the card when plugged in some PCI slots, =20
whereas in one of the slots I do see a non-zero value.
It would be great if you could help me understand the issue.
I am sorry if the question is inapporpriate in the group. I am =20
desperate to solve the issue.
Thanks for any help.
You need to find out how the PCI edge interrupts are wired on you =20
board than we can talk about how to generate an interrupt based on =20
that. I'd guess IRQ_OUT is wired to INTA, but it would be good to =20
verify that.
- k
J.Joseph
----- Original Message ----
From: Kumar Gala <redacted>
To: Wang Matthew-R59995 <redacted>
Cc: linuxppc-embedded@ozlabs.org
Sent: Wednesday, 18 October, 2006 6:54:24 PM
Subject: Re: Linuxppc-embedded Digest, Vol 26, Issue 36
On Oct 18, 2006, at 8:10 PM, Wang Matthew-R59995 wrote:
quoted
Hi Kumar,
Actually I do many trials about it. Vxwerks Bootrom is smaller than
U-Boot. The key difference between Bootrom and U-boot is that some
source code of Bootrom is invisible to the users.
Actually the rfi instruction which I point out is the first rfi
instruction of Linux PowerPC bringup.
Before that, it's TLB entry invalidation and temp TLB entry mapping.
I check MMU setting carefully before coming Linux Kernel.
I just want to know if other guys met similar scenario like me. I
don't
need the precise answer, just overall suggestion about it because I
understand that not everyone has the same bootloader of mine, that
bootloader is actually a customized bootloader.
I understand that, thus I was asking what exact problem you were
seeing to try and help.
quoted
Anyway thank you.
R9 point to LR register, mask the high 20 bit of r9 and send to r7,
and
then add 24, which means stride 6 instructions for rfi instruction
execution.
Of course, rfi can switch the TLB entry, both the previous TLB
entry and
the temp TLB entry point to the same physical address.
I've checked it.
I know what the code does, I wrote it :)
- kumar
_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Here=92s a new way to find what you're looking for - Yahoo! Answers