RE: pci_enable_device fails on MPC8541

HI Kumar,
I have attached the /proc/ioports and /proc/iomem for 8541E.
Also the CONFIG_ 85XX_PCI2 is set to yes.

Freescale does not support 2.6.13 so I am not able to update to that
version yet.

Thanks,
Bizhan

-----Original Message-----
From: Kumar Gala [mailto:kumar.gala@freescale.com] 
Sent: Wednesday, August 10, 2005 12:11 PM
To: Bizhan Gholikhamseh (bgholikh)
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: pci_enable_device fails on MPC8541

No problem.  I'm hunting around the problem, but trying to figure out
exactly where the bug is.  What's a little odd is that in 2.6.11 we  
should have excluded all the devices that are on the VIA chipset.   
However, in the logs you sent me we see those devices. Part of the
problem is that your TI DSP has its own P2P bridge on it.  Therefor the
bus numbers for the devices start changing around a bit.

What is CONFIG_85xx_PCI2 set to in your .config?

Can you send me the output of the following on the 8555 CDS:
cat /proc/ioports
cat /proc/iomem

Also, if you feel daring, grab the latest 2.6.13-rc6 kernel and build it
for 8555 CDS and see what happens.

Oh, is this card something standard or a custom thing?  The issue of  
having a card with P2P bridge on it has come up more than once.   
However, I'm not sure of any standard PC PCI cards do this (at least
none of the simple cards we have do).  I'd like to see if we can find
something that we could start testing with.

thanks

- kumar

On Aug 10, 2005, at 1:03 PM, Bizhan Gholikhamseh \(((bgholikh\))) wrote:

Kumar,
Sorry it took a while. I have attached the 8540 PCI boot log and 
/proc/pci. Also I found out the functions you mentioned are not used 
in my environment.

Thanks,
Bizhan

-----Original Message-----
From: Kumar Gala [mailto:kumar.gala@freescale.com]
Sent: Wednesday, August 10, 2005 9:06 AM
To: Bizhan Gholikhamseh (bgholikh)
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: pci_enable_device fails on MPC8541

It would be extremely helpful to get the output from the work MPC8540 
for lspci and cat /proc/pci.

Also, I forget if 2.6.11 has CDS VIA support, but if it does you can 
try disabling it by commenting out the calls to:
mpc85xx_cds_enable_via() & mpc85xx_cds_fixup_via() in arch/ppc/syslib/

ppc85xx_setup.c and see what happens.

- k

On Aug 10, 2005, at 10:58 AM, Bizhan Gholikhamseh \\((bgholikh\\))
wrote:

quoted

 <<pci_boot.pdf>> Kumar,
We do not support or care about VIA IDE controller. I have enabled 
the

quoted

DEBUG flag and attached the debug messages during boot. This is for 
8541E.
Regards,
Bizhan

-----Original Message-----
From: Kumar Gala [mailto:kumar.gala@freescale.com]
Sent: Tuesday, August 09, 2005 4:11 PM
To: Bizhan Gholikhamseh (bgholikh)
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: pci_enable_device fails on MPC8541

Do you need support for the VIA IDE controller?  I'm not sure if that

quoted

is causing you issues.

Also, can you try enabling DEBUG in arch/ppc/kernel/pci.c and send a 
boot log.  I'm trying to figure out what is causing the resource 
conflict.  It appears that the memory resource is reasonable, but 
there could be possible conflict on the IO resource side.

Also, if you can send logs of the same thing from the working 8540 
ADS

quoted

that would be helpful.

- kumar

On Aug 9, 2005, at 12:18 PM, Bizhan Gholikhamseh \(((bgholikh\)))
wrote:

quoted

Hi Kumar,
I am using Linux 2.6.11, u-boot 1.1.2.
I see failure in pci_enable_device with message:
"PCI: Device 0000:02:01.0 not available because of resource 
collisions"

I have attached three files:
lspci_output.txt: out put of the "lspci -v"
proc_pci.txt: output of the "cat /proc/pci"
u-boot.txt: output of the "pci command at u-boot"

Any help greatly appreciated,
Bizhan
-----Original Message-----
From: Kumar Gala [mailto:kumar.gala@freescale.com]
Sent: Monday, August 08, 2005 1:34 PM
To: Bizhan Gholikhamseh (bgholikh)
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: pci_enable_device fails on MPC8541

Bizhan,

A few questions:

1. what kernel version are you using on these boards:
2. can you do an lspci -v on the boards

- kumar

On Aug 8, 2005, at 1:12 PM, Bizhan Gholikhamseh \(((bgholikh\)))
wrote:

quoted

Hi All,
I am using two evaluation board from freescale, 8540ADS and 
MPC8541.
The same PCI driver is being compiled and loaded on both platforms.
The same PCI driver (developed by me) for DSP board compiled and 
loaded on both platforms.

When I type: "insmod C6415.ko" on 8541 board, I get the following
error:
"PCI: Device 0000:02:01.0 not available because of resource 
collisions"
This messages is because of the execution of the generic PCI Linux
command:
"pci_enable_device(pdev)"
The same API has no problem on 8540ADS.

quoted

From UBOOT I can see my device is on bus 3:

=> pci 3
Scanning PCI devices on bus 3
BusDev FUN    VendorID    DeviceID    Device Class    Sub-Class
-------------------------------------------------------------------
-

quoted

quoted

quoted

-

quoted

quoted

-
--
--------------------
03.01.00            0x104c    0xa106        .........

Any idea why the insmod fails on one board and not on the other 
one?

Many thanks in advance,
Bizhan

<ATT2118305.txt>


<lspci_output.txt>
<proc_pci.txt>
<u-boot.txt>

<pci_boot.txt>
<pci_boot.pdf>

<pci_boot_8540.txt>
<proc_pci_8540.txt>