[PATCH v2 8/8] dt-bindings: nfc: marvell,nci: convert to dtschema

@@ -0,0 +1,170 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/nfc/marvell,nci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell International Ltd. NCI NFC controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+  compatible:
+    enum:
+      - marvell,nfc-i2c
+      - marvell,nfc-spi
+      - marvell,nfc-uart
+
+  hci-muxed:
+    type: boolean
+    description: |
+      Specifies that the chip is muxing NCI over HCI frames
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  reset-n-io:
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    maxItems: 1
+    description: |
+      Output GPIO pin used to reset the chip (active low)
+
+  i2c-int-falling:
+    type: boolean
+    description: |
+      For I2C type of connection. Specifies that the chip read event shall be
+      trigged on falling edge.
+
+  i2c-int-rising:
+    type: boolean
+    description: |
+      For I2C type of connection.  Specifies that the chip read event shall be
+      trigged on rising edge.
+
+  break-control:
+    type: boolean
+    description: |
+      For UART type of connection. Specifies that the chip needs specific break
+      management.
+
+  flow-control:
+    type: boolean
+    description: |
+      For UART type of connection. Specifies that the chip is using RTS/CTS.
+
+  spi-cpha: true
+  spi-cpol: true
+  spi-max-frequency: true
+
+required:
+  - compatible
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,nfc-i2c
+    then:
+      properties:
+        break-control: false
+        flow-control: false
+        spi-cpha: false
+        spi-cpol: false
+        spi-max-frequency: false
+      required:
+        - reg
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,nfc-spi
+    then:
+      properties:
+        break-control: false
+        flow-control: false
+        i2c-int-falling: false
+        i2c-int-rising: false
+      required:
+        - reg
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: marvell,nfc-uart
+    then:
+      properties:
+        i2c-int-falling: false
+        i2c-int-rising: false
+        interrupts: false
+        spi-cpha: false
+        spi-cpol: false
+        spi-max-frequency: false
+        reg: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        nfc@8 {
+            compatible = "marvell,nfc-i2c";
+            reg = <0x8>;
+
+            interrupt-parent = <&gpio3>;
+            interrupts = <21 IRQ_TYPE_EDGE_RISING>;
+
+            i2c-int-rising;
+
+            reset-n-io = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        nfc@0 {
+            compatible = "marvell,nfc-spi";
+            reg = <0>;
+
+            spi-max-frequency = <3000000>;
+            spi-cpha;
+            spi-cpol;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+
+            reset-n-io = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    uart {
+        nfc {
+            compatible = "marvell,nfc-uart";
+
+            reset-n-io = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+
+            hci-muxed;
+            flow-control;
+        };
+    };

@@ -1,84 +0,0 @@
-* Marvell International Ltd. NCI NFC Controller
-
-Required properties:
-- compatible: Should be:
-  - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices
-  - "marvell,nfc-i2c" for I2C devices
-  - "marvell,nfc-spi" for SPI devices
-
-Optional SoC specific properties:
-- pinctrl-names: Contains only one value - "default".
-- pintctrl-0: Specifies the pin control groups used for this controller.
-- reset-n-io: Output GPIO pin used to reset the chip (active low).
-- hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
-
-Optional UART-based chip specific properties:
-- flow-control: Specifies that the chip is using RTS/CTS.
-- break-control: Specifies that the chip needs specific break management.
-
-Optional I2C-based chip specific properties:
-- i2c-int-falling: Specifies that the chip read event shall be trigged on
-  		   falling edge.
-- i2c-int-rising: Specifies that the chip read event shall be trigged on
-  		  rising edge.
-
-Example (for ARM-based BeagleBoard Black with 88W8887 on UART5):
-
-&uart5 {
-
-	nfcmrvluart: nfcmrvluart@5 {
-		compatible = "marvell,nfc-uart";
-
-		reset-n-io = <&gpio3 16 0>;
-
-		hci-muxed;
-		flow-control;
-        }
-};
-
-
-Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1):
-
-&i2c1 {
-	clock-frequency = <400000>;
-
-	nfcmrvli2c0: i2c@1 {
-		compatible = "marvell,nfc-i2c";
-
-		reg = <0x8>;
-
-		/* I2C INT configuration */
-		interrupt-parent = <&gpio3>;
-		interrupts = <21 0>;
-
-		/* I2C INT trigger configuration */
-		i2c-int-rising;
-
-		/* Reset IO */
-		reset-n-io = <&gpio3 19 0>;
-	};
-};
-
-
-Example (for ARM-based BeagleBoard Black on SPI0):
-
-&spi0 {
-
-	mrvlnfcspi0: spi@0 {
-		compatible = "marvell,nfc-spi";
-
-		reg = <0>;
-
-		/* SPI Bus configuration */
-		spi-max-frequency = <3000000>;
-		spi-cpha;
-		spi-cpol;
-
-		/* SPI INT configuration */
-		interrupt-parent = <&gpio1>;
-		interrupts = <17 0>;
-
-		/* Reset IO */
-       		reset-n-io = <&gpio3 19 0>;
-	};
-};