[PATCH 3/3] brcmfmac: make setting SDIO workqueue WQ_HIGHPRI a module parameter

@@ -71,6 +71,10 @@ static int brcmf_eap_restrict;
 module_param_named(eap_restrict, brcmf_eap_restrict, int, 0400);
 MODULE_PARM_DESC(eap_restrict, "Block non-802.1X frames until auth finished");
 
+static int brcmf_sdio_wq_highpri;
+module_param_named(sdio_wq_highpri, brcmf_sdio_wq_highpri, int, 0);
+MODULE_PARM_DESC(sdio_wq_highpri, "Set SDIO workqueue to high priority");
+
 #ifdef DEBUG
 /* always succeed brcmf_bus_started() */
 static int brcmf_ignore_probe_fail;

@@ -418,6 +422,7 @@ struct brcmf_mp_device *brcmf_get_module_param(struct device *dev,
 	settings->roamoff = !!brcmf_roamoff;
 	settings->iapp = !!brcmf_iapp_enable;
 	settings->eap_restrict = !!brcmf_eap_restrict;
+	settings->sdio_wq_highpri = !!brcmf_sdio_wq_highpri;
 #ifdef DEBUG
 	settings->ignore_probe_fail = !!brcmf_ignore_probe_fail;
 #endif

@@ -38,6 +38,7 @@ extern struct brcmf_mp_global_t brcmf_mp_global;
  * @fcmode: FWS flow control.
  * @roamoff: Firmware roaming off?
  * @eap_restrict: Not allow data tx/rx until 802.1X auth succeeds
+ * @sdio_wq_highpri: Tasks submitted to SDIO workqueue will run immediately.
  * @ignore_probe_fail: Ignore probe failure.
  * @country_codes: If available, pointer to struct for translating country codes
  * @bus: Bus specific platform data. Only SDIO at the mmoment.

@@ -49,6 +50,7 @@ struct brcmf_mp_device {
 	bool		roamoff;
 	bool		iapp;
 	bool		eap_restrict;
+	bool		sdio_wq_highpri;
 	bool		ignore_probe_fail;
 	struct brcmfmac_pd_cc *country_codes;
 	const char	*board_type;

@@ -4342,9 +4342,21 @@ struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev)
 	bus->txminmax = BRCMF_TXMINMAX;
 	bus->tx_seq = SDPCM_SEQ_WRAP - 1;
 
+	/* attempt to attach to the dongle */
+	if (!(brcmf_sdio_probe_attach(bus))) {
+		brcmf_err("brcmf_sdio_probe_attach failed\n");
+		goto fail;
+	}
+
 	/* single-threaded workqueue */
-	wq = alloc_ordered_workqueue("brcmf_wq/%s", WQ_MEM_RECLAIM,
-				     dev_name(&sdiodev->func1->dev));
+	if (sdiodev->settings->sdio_wq_highpri) {
+		wq = alloc_workqueue("brcmf_wq/%s",
+				     WQ_HIGHPRI | WQ_MEM_RECLAIM | WQ_UNBOUND,
+				     1, dev_name(&sdiodev->func1->dev));
+	} else {
+		wq = alloc_ordered_workqueue("brcmf_wq/%s", WQ_MEM_RECLAIM,
+					     dev_name(&sdiodev->func1->dev));
+	}
 	if (!wq) {
 		brcmf_err("insufficient memory to create txworkqueue\n");
 		goto fail;

@@ -4353,12 +4365,6 @@ struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev)
 	INIT_WORK(&bus->datawork, brcmf_sdio_dataworker);
 	bus->brcmf_wq = wq;
 
-	/* attempt to attach to the dongle */
-	if (!(brcmf_sdio_probe_attach(bus))) {
-		brcmf_err("brcmf_sdio_probe_attach failed\n");
-		goto fail;
-	}
-
 	spin_lock_init(&bus->rxctl_lock);
 	spin_lock_init(&bus->txq_lock);
 	init_waitqueue_head(&bus->ctrl_wait);