[PATCH] dt-bindings: usb: Use consistent indentation in the example
COOLING11d
From: Krzysztof Kozlowski <hidden>
Date: 2026-09-13 12:32:53
Also in:
linux-devicetree, lkml
Subsystem:
open firmware and flattened device tree bindings, the rest, usb subsystem · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds, Greg Kroah-Hartman
Correct indentation in the examples to consistent 2- or 4-spaces
indentation to fix dt-check-style warnings ("example 0
[indent-consistent] indent mismatch ..."). Preferred is 4-spaces, but
re-indenting entire example just for that is too much churn.
Signed-off-by: Krzysztof Kozlowski <redacted>
---
.../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 2 +-
.../bindings/usb/corechips,sl6341.yaml | 20 +++++++-------
.../bindings/usb/maxim,max3421.yaml | 12 ++++-----
.../devicetree/bindings/usb/nxp,ptn5110.yaml | 8 +++---
.../bindings/usb/realtek,rts5411.yaml | 2 +-
.../devicetree/bindings/usb/ti,j721e-usb.yaml | 26 +++++++++----------
.../devicetree/bindings/usb/ti,usb8041.yaml | 4 +--
7 files changed, 37 insertions(+), 37 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
index 620b564914d4..26731c45a604 100644
--- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
+++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml@@ -130,7 +130,7 @@ examples: phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; itc-setting = <0x4>; /* 4 micro-frames */ - /* Incremental burst of unspecified length */ + /* Incremental burst of unspecified length */ ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>;
diff --git a/Documentation/devicetree/bindings/usb/corechips,sl6341.yaml b/Documentation/devicetree/bindings/usb/corechips,sl6341.yaml
index 82996791aaf1..4ddfc7594846 100644
--- a/Documentation/devicetree/bindings/usb/corechips,sl6341.yaml
+++ b/Documentation/devicetree/bindings/usb/corechips,sl6341.yaml@@ -61,19 +61,19 @@ examples: /* 2.0 hub */ hub_2_0: hub@1 { - compatible = "usb3431,6241"; - reg = <1>; - peer-hub = <&hub_3_0>; - reset-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; - vdd1v1-supply = <&vdd1v1_hub>; + compatible = "usb3431,6241"; + reg = <1>; + peer-hub = <&hub_3_0>; + reset-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + vdd1v1-supply = <&vdd1v1_hub>; }; /* 3.0 hub */ hub_3_0: hub@2 { - compatible = "usb3431,6341"; - reg = <2>; - peer-hub = <&hub_2_0>; - reset-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; - vdd1v1-supply = <&vdd1v1_hub>; + compatible = "usb3431,6341"; + reg = <2>; + peer-hub = <&hub_2_0>; + reset-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + vdd1v1-supply = <&vdd1v1_hub>; }; };
diff --git a/Documentation/devicetree/bindings/usb/maxim,max3421.yaml b/Documentation/devicetree/bindings/usb/maxim,max3421.yaml
index 4639be7ab059..042dfc3467d2 100644
--- a/Documentation/devicetree/bindings/usb/maxim,max3421.yaml
+++ b/Documentation/devicetree/bindings/usb/maxim,max3421.yaml@@ -57,11 +57,11 @@ examples: #size-cells = <0>; usb@0 { - compatible = "maxim,max3421"; - reg = <0>; - maxim,vbus-en-pin = <3 1>; - spi-max-frequency = <26000000>; - interrupt-parent = <&gpio>; - interrupts = <42>; + compatible = "maxim,max3421"; + reg = <0>; + maxim,vbus-en-pin = <3 1>; + spi-max-frequency = <26000000>; + interrupt-parent = <&gpio>; + interrupts = <42>; }; };
diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
index 581e5916eadd..fe9a02f21c67 100644
--- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
+++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml@@ -67,10 +67,10 @@ examples: #size-cells = <0>; port@0 { - reg = <0>; - typec1_dr_sw: endpoint { - remote-endpoint = <&usb1_drd_sw>; - }; + reg = <0>; + typec1_dr_sw: endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; }; }; };
diff --git a/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml b/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml
index a020afaf2d6e..9c8868c478c0 100644
--- a/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml
+++ b/Documentation/devicetree/bindings/usb/realtek,rts5411.yaml@@ -84,7 +84,7 @@ examples: port@4 { reg = <4>; endpoint { - remote-endpoint = <&usb_a0_ss>; + remote-endpoint = <&usb_a0_ss>; }; }; };
diff --git a/Documentation/devicetree/bindings/usb/ti,j721e-usb.yaml b/Documentation/devicetree/bindings/usb/ti,j721e-usb.yaml
index 0aaaadb584e4..176737156d77 100644
--- a/Documentation/devicetree/bindings/usb/ti,j721e-usb.yaml
+++ b/Documentation/devicetree/bindings/usb/ti,j721e-usb.yaml@@ -94,19 +94,19 @@ examples: #size-cells = <2>; usb@6000000 { - compatible = "cdns,usb3"; - reg = <0x00 0x6000000 0x00 0x10000>, - <0x00 0x6010000 0x00 0x10000>, - <0x00 0x6020000 0x00 0x10000>; - reg-names = "otg", "xhci", "dev"; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ - <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ - <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ - interrupt-names = "host", - "peripheral", - "otg"; - maximum-speed = "super-speed"; - dr_mode = "otg"; + compatible = "cdns,usb3"; + reg = <0x00 0x6000000 0x00 0x10000>, + <0x00 0x6010000 0x00 0x10000>, + <0x00 0x6020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; /* otgirq.0 */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; }; }; };
diff --git a/Documentation/devicetree/bindings/usb/ti,usb8041.yaml b/Documentation/devicetree/bindings/usb/ti,usb8041.yaml
index 07e13fae640b..e75956f0f85a 100644
--- a/Documentation/devicetree/bindings/usb/ti,usb8041.yaml
+++ b/Documentation/devicetree/bindings/usb/ti,usb8041.yaml@@ -65,8 +65,8 @@ examples: reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; hub@1 { - compatible = "usb123,4567"; - reg = <1>; + compatible = "usb123,4567"; + reg = <1>; }; };
--
2.53.0