On Wed, Aug 20, 2025 at 4:04 PM Andrew Davis [off-list ref] wrote:

On 8/20/25 1:10 PM, Jonathan Cormier wrote:

quoted

Add trace events to help debug and measure the speed of the
communication channel.

Add parsing of the messages types but I am not sure how to parse the
flags, since the REQ and RESP flags conflict. Left as seperate commit to

The REQ and RESP flags should be handled by different TRACE_EVENTs. Right
now you only dump the content of the response messages (the ones in
rx_callback), also tracing what is sent is just as important, so you
might want to add slightly different ti_sci_msg_dump EVENT for the
sending side which uses the different REQ flag parser.

Does it make sense to have seperate trace events, one that only decode
the hdrs and ones that also include the buffers?

I'm bothered by the code duplication, but am trying to convince myself
it doesn't matter.

Currently, with the above updates, if you enabled all the traces,
you'd see something like:

[15.579036] ti_sci_xfer_begin: type=SET_DEVICE_STATE host=0C seq=00
flags=00000402 status=0
[15.xxxxxxx] ti_sci_tx_msg_dump: type=SET_DEVICE_STATE host=0C seq=00
flags=00000402 data=<data>
[15.587595] ti_sci_rx_callback: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0
[15.xxxxxxx] ti_sci_rx_msg_dump: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 data=<data>
[15.606135] ti_sci_xfer_end: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0

Presumably if you were worried about timing, you'd disable the
msg_dumps, avoiding the extra memcpy's.  And if you only cared about
the data being sent, you'd only enable the msg_dumps.  Does this make
sense / is it worth the extra trace calls?

Or removing the buffer decoding in the msg_dumps, removes the duplication:

[15.579036] ti_sci_xfer_begin: type=SET_DEVICE_STATE host=0C seq=00
flags=00000402 status=0
[15.xxxxxxx] ti_sci_msg_dump: data=<data>
[15.587595] ti_sci_rx_callback: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0
[15.xxxxxxx] ti_sci_msg_dump: data=<data>
[15.606135] ti_sci_xfer_end: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0

Or do condense the trace calls so they all have the data into something like:

[15.579036] ti_sci_xfer_begin: type=SET_DEVICE_STATE host=0C seq=00
flags=00000402 status=0  data=<data>
[15.587595] ti_sci_rx_callback: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0 data=<data>
[15.606135] ti_sci_xfer_end: type=SET_DEVICE_STATE host=0C seq=00
flags=00000002 status=0

Simplifying the code in the trace header.

Andrew

quoted

make it easier to drop or make changes depending on comments.  The two
commits should squash easily.

Nishanth Menon and Vignesh Raghavendra requested I send this patch
upstream.

Signed-off-by: Jonathan Cormier <redacted>
---
Jonathan Cormier (2):
       firmware: ti_sci: Add trace events
       firmware: ti_sci: trace: Decode message types

  MAINTAINERS                     |   1 +
  drivers/firmware/Makefile       |   3 +
  drivers/firmware/ti_sci.c       |  11 +++
  drivers/firmware/ti_sci_trace.h | 146 ++++++++++++++++++++++++++++++++++++++++
  4 files changed, 161 insertions(+)
---
base-commit: d7b8f8e20813f0179d8ef519541a3527e7661d3a
change-id: 20250709-linux_master_ti_sci_trace-91fd2af65dca

Best regards,

-- 
Jonathan Cormier
Senior Software Engineer

Voice:  315.425.4045 x222

http://www.CriticalLink.com
6712 Brooklawn Parkway, Syracuse, NY 13211