[RESEND PATCH v8 05/10] dt-bindings: sc16is7xx: Add property to change GPIO function
From: Hugo Villeneuve <hidden>
Date: 2023-07-21 16:20:58
Also in:
linux-devicetree, linux-gpio, lkml, stable
Subsystem:
open firmware and flattened device tree bindings, the rest, tty layer and serial drivers · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds, Greg Kroah-Hartman, Jiri Slaby
From: Hugo Villeneuve <hvilleneuve@dimonoff.com> Some variants in this series of UART controllers have GPIO pins that are shared between GPIO and modem control lines. The pin mux mode (GPIO or modem control lines) can be set for each ports (channels) supported by the variant. This adds a property to the device tree to set the GPIO pin mux to modem control lines on selected ports if needed. Cc: <redacted> # 6.1.x Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com> Acked-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Lech Perczak <redacted> --- .../bindings/serial/nxp,sc16is7xx.txt | 46 +++++++++++++++++++ 1 file changed, 46 insertions(+)
diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
index 0fa8e3e43bf8..1a7e4bff0456 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt@@ -23,6 +23,9 @@ Optional properties: 1 = active low. - irda-mode-ports: An array that lists the indices of the port that should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. Example: sc16is750: sc16is750@51 {
@@ -35,6 +38,26 @@ Example: #gpio-cells = <2>; }; + sc16is752: sc16is752@53 { + compatible = "nxp,sc16is752"; + reg = <0x53>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@54 { + compatible = "nxp,sc16is752"; + reg = <0x54>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + }; + * spi as bus Required properties:
@@ -59,6 +82,9 @@ Optional properties: 1 = active low. - irda-mode-ports: An array that lists the indices of the port that should operate in IrDA mode. +- nxp,modem-control-line-ports: An array that lists the indices of the port that + should have shared GPIO lines configured as + modem control lines. Example: sc16is750: sc16is750@0 {
@@ -70,3 +96,23 @@ Example: gpio-controller; #gpio-cells = <2>; }; + + sc16is752: sc16is752@1 { + compatible = "nxp,sc16is752"; + reg = <1>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */ + gpio-controller; /* Port 0 as GPIOs */ + #gpio-cells = <2>; + }; + + sc16is752: sc16is752@2 { + compatible = "nxp,sc16is752"; + reg = <2>; + clocks = <&clk20m>; + interrupt-parent = <&gpio3>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */ + };
--
2.30.2