[PATCH 2/2] tty: amba-pl011: use iotype instead of access_32b to track 32-bit I/O
From: Timur Tabi <hidden>
Date: 2016-01-04 21:37:46
Also in:
linux-arm-msm
Subsystem:
arm primecell uart pl010 and pl011 drivers, documentation, the rest, tty layer and serial drivers · Maintainers:
Russell King, Jonathan Corbet, Linus Torvalds, Greg Kroah-Hartman, Jiri Slaby
Instead of defining a new field in the uart_amba_port structure, use the
existing iotype field of the uart_port structure, which is intended for
this purpose. If we need to use 32-bit register access, we set iotype
to UPIO_MEM32, otherwise we set it to UPIO_MEM.
For early console, specify the "mmio32" option on the kernel command-line.
Example:
earlycon=pl011,mmio32,0x3ced1000
Signed-off-by: Timur Tabi <redacted>
---
Documentation/kernel-parameters.txt | 5 ++++-
drivers/tty/serial/amba-pl011.c | 16 +++++++++-------
2 files changed, 13 insertions(+), 8 deletions(-)
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 474ce69..ab11d5c 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt@@ -995,10 +995,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted. unspecified, the h/w is not initialized. pl011,<addr> + pl011,mmio32,<addr> Start an early, polled-mode console on a pl011 serial port at the specified address. The pl011 serial port must already be setup and configured. Options are not - yet supported. + yet supported. If 'mmio32' is specified, then only + the driver will use only 32-bit accessors to read/write + the device registers. msm_serial,<addr> Start an early, polled-mode console on an msm serial
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 42aabb84..80df184 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c@@ -239,7 +239,6 @@ struct uart_amba_port { unsigned int fifosize; /* vendor-specific */ unsigned int old_cr; /* state during shutdown */ bool autorts; - bool access_32b; unsigned int fixed_baud; /* vendor-set fixed baud rate */ char type[12]; #ifdef CONFIG_DMA_ENGINE
@@ -263,7 +262,8 @@ static unsigned int pl011_read(const struct uart_amba_port *uap, { void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg); - return uap->access_32b ? readl_relaxed(addr) : readw_relaxed(addr); + return (uap->port.iotype == UPIO_MEM32) ? + readl_relaxed(addr) : readw_relaxed(addr); } static void pl011_write(unsigned int val, const struct uart_amba_port *uap,
@@ -271,7 +271,7 @@ static void pl011_write(unsigned int val, const struct uart_amba_port *uap, { void __iomem *addr = uap->port.membase + pl011_reg_to_offset(uap, reg); - if (uap->access_32b) + if (uap->port.iotype == UPIO_MEM32) writel_relaxed(val, addr); else writew_relaxed(val, addr);
@@ -2304,7 +2304,10 @@ static void pl011_putc(struct uart_port *port, int c) { while (readl(port->membase + UART01x_FR) & UART01x_FR_TXFF) ; - writeb(c, port->membase + UART01x_DR); + if (port->iotype == UPIO_MEM32) + writel(c, port->membase + UART01x_DR); + else + writeb(c, port->membase + UART01x_DR); while (readl(port->membase + UART01x_FR) & UART01x_FR_BUSY) ; }
@@ -2417,7 +2420,6 @@ static int pl011_setup_port(struct device *dev, struct uart_amba_port *uap, uap->port.dev = dev; uap->port.mapbase = mmiobase->start; uap->port.membase = base; - uap->port.iotype = UPIO_MEM; uap->port.fifosize = uap->fifosize; uap->port.flags = UPF_BOOT_AUTOCONF; uap->port.line = index;
@@ -2471,9 +2473,9 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) return PTR_ERR(uap->clk); uap->reg_offset = vendor->reg_offset; - uap->access_32b = vendor->access_32b; uap->vendor = vendor; uap->fifosize = vendor->get_fifosize(dev); + uap->port.iotype = vendor->access_32b ? UPIO_MEM32 : UPIO_MEM; uap->port.irq = dev->irq[0]; uap->port.ops = &amba_pl011_pops;
@@ -2552,9 +2554,9 @@ static int sbsa_uart_probe(struct platform_device *pdev) return -ENOMEM; uap->reg_offset = vendor_sbsa.reg_offset; - uap->access_32b = vendor_sbsa.access_32b; uap->vendor = &vendor_sbsa; uap->fifosize = 32; + uap->port.iotype = vendor_sbsa.access_32b ? UPIO_MEM32 : UPIO_MEM; uap->port.irq = platform_get_irq(pdev, 0); uap->port.ops = &sbsa_uart_pops; uap->fixed_baud = baudrate;
--
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project.