Re: How do I tell which disk failed?

On Mon, 2013-01-07 at 23:19 -0600, Stan Hoeppner wrote:

On 1/7/2013 8:05 PM, Ross Boylan wrote:

quoted

I see my array is reconstructing, but I can't tell which disk failed.

quoted

md0 : active raid1 sda1[0] sdc2[2] sdb2[1]
      96256 blocks [3/3] [UUU]

md1 : active raid1 sda3[0] sdc4[2] sdb4[1]
      730523648 blocks [3/3] [UUU]

Your two md/RAID1 arrays are built on partitions on the same set of 3
disks.  You likely didn't have a disk failure, or md0 would be
rebuilding as well.  Your failure, or hiccup, is of some other nature,
and apparently only affected md1.

I assume something went wrong while accessing one of the partitions, and
that there is a problem with the disk that partition is on.

Phrased more carefully, which partition failed and is being resynced
into md1?  I can't tell. 

If I knew, would it be safe to mdadm -fail that partition in the midst
of the rebuild?  

Once the system starts md0 is almost never accessed (it's /boot).

quoted

      [>....................]  resync =  0.4% (3382400/730523648) finish=14164.9min speed=855K/sec

Rebuilding a RAID1 on modern hardware should scream.  You're getting
resync throughput of less than 1MB/s.  Estimated completion time is 9.8
_days_ to rebuild a mirror partition.  This is insanely high.

Yes.  It seems to be doing better now:
# date; cat /proc/mdstat
Mon Jan  7 21:37:46 PST 2013
Personalities : [raid1]
md0 : active raid1 sda1[0] sdc2[2] sdb2[1]
      96256 blocks [3/3] [UUU]

md1 : active raid1 sda3[0] sdc4[2] sdb4[1]
      730523648 blocks [3/3] [UUU]
      [===========>.........]  resync = 57.8% (422846976/730523648) finish=452.5min speed=11329K/sec

unused devices: <none>

This is more in line with what I remember when I originally synced the
partitions, which I remember as 4-6 hours (it's clearly still much
slower than that pace).

Either you've tweaked your resync throughput down to 1MB/s, or you have
some other process(es) doing serious IO, robbing the resync of
throughput.  

Isn't it possible there's a hardware problem, e.g., leading to a
failure/retry cycle?

Consider running iotop to determine if another process(es)
is eating IO bandwidth.

I did, though it's probably a little late.  Here's a fairly typical result (command line as shown on the
last line)
Total DISK READ: 99.09 K/s | Total DISK WRITE: 25.26 K/s
  PID USER      DISK READ  DISK WRITE   SWAPIN    IO    COMMAND
 4263 root           0 B/s       0 B/s  0.00 %  8.40 % [kjournald]
 1204 root       99.09 K/s       0 B/s  0.00 %  4.68 % [kcopyd]
 1193 root           0 B/s       0 B/s  0.00 %  4.68 % [kdmflush]
11874 root           0 B/s   25.26 K/s  0.00 %  0.00 % python /usr/bin/iotop -d 2 -n 20 -b

When I restarted the system had been effectively down for ~ 1.5 days,
and so I guess it's possible that lots of housekeeping operation was
going on.  However, top didn't show any noticeable use of CPU.

A more recent check show speed continuing to rise; it the value is an
average and it started slow that would explain it:
 date; cat /proc/mdstat
Mon Jan  7 22:56:23 PST 2013
Personalities : [raid1]
md0 : active raid1 sda1[0] sdc2[2] sdb2[1]
      96256 blocks [3/3] [UUU]

md1 : active raid1 sda3[0] sdc4[2] sdb4[1]
      730523648 blocks [3/3] [UUU]
      [==================>..]  resync = 91.8% (670929280/730523648) finish=19.4min speed=51057K/sec

Ross