Re: Device utilization with RAID-1

On Thu, 18 Aug 2011 02:26:17 +0200 Harald Nikolisin [off-list ref]
wrote:

hi,

I didn't want to complain in general about SW RAID-1 performance. I
simply think something is wrong with my setup and I have currently no
idea how to improve.

The basic questions (where I did not find an answer, neither in FAQ's
nor in forum discussions) are.
a) Is it normal that the hard drives show an permanent utilization
(around 20%) without any noticeable actions on the computer?

No.  If the array is resyncing or recovering then you would expect
utilization for as many hours as it takes - but that would show
in /proc/mdstat.

b) Should (as long as no resync happens) the state of mdadm active or clean?

If anything has been written to the device in the last 200msec (including
e.g. access time updates) then expect it to be 'active'.
If nothing has been written for 200msecc or more, then expect it to be clean.

If you crash while it is active, a resync is needed.
If you crash while it is clean, no resync is needed.
If you don't crash at all .... that is best :-)

NeilBrown

cheers,
  harald

well, I have only 2 hard drives and no space for more..

Am 16.08.2011 03:29, schrieb Roberto Spadim:

quoted

try raid10 far layout

2011/8/15 Harald Nikolisin <hochglanz@gmail.com
<mailto:hochglanz@gmail.com>>

    Since a long time I'm unhappy with the performance of my RAID-1 system.
    Investigation with atop and iostat unveils that the disk utilization is
    always on a certain level although nothing happens on the system. In the
    case of reading or writing files the utilization boosts always to 100%
    for a long time. Very ugly examples are "Firefox starting" or "zypper
    updates".
    That is snapshot of the output of iostat:


    Device:         rrqm/s   wrqm/s     r/s     w/s   rsec/s   wsec/s
    avgrq-sz avgqu-sz   await  svctm  %util
    sda               0,00     0,00    0,00    7,33     0,00    43,33
    5,91     0,33   43,18  33,32  24,43
    sdb               0,00     0,00    0,00    7,33     0,00    43,33
    5,91     0,35   45,59  39,73  29,13
    md0               0,00     0,00    0,00    0,67     0,00     5,33
    8,00     0,00    0,00   0,00   0,00
    md1               0,00     0,00    0,00    0,33     0,00     5,33
    16,00     0,00    0,00   0,00   0,00
    md2               0,00     0,00    0,00    0,33     0,00     1,00
    3,00     0,00    0,00   0,00   0,00
    md3               0,00     0,00    0,00    0,00     0,00     0,00
    0,00     0,00    0,00   0,00   0,00
    md4               0,00     0,00    0,00    0,00     0,00     0,00
    0,00     0,00    0,00   0,00   0,00
    md5               0,00     0,00    0,00    0,33     0,00     0,67
    2,00     0,00    0,00   0,00   0,00

    I checked with mdadm if a resync happens or so, but this is not the
    case. The state says "active" on all RAID devices - btw. what is the
    difference to "clean" ?

    thanks for any hints,
     harald
    --
    To unsubscribe from this list: send the line "unsubscribe linux-raid" in
    the body of a message to majordomo@vger.kernel.org
    <mailto:majordomo@vger.kernel.org>
    More majordomo info at  http://vger.kernel.org/majordomo-info.html




-- 
Roberto Spadim
Spadim Technology / SPAEmpresarial

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html