Bill Davidsen [off-list ref] writes:
Ferenc Wagner wrote:
quoted
I use an FC SAN, which provides multiple pathes to multiple LUNs.
These all come up as different sd* devices, exhausting single letter
names. I mean they are a LOT. Using the md mulitpath driver
everything works perfectly, no problems there. However, during boot,
the kernel tries to read the partition table from each device,
spitting out hundreds of lines of error messages: most of the devices
aren't even readable, and those which are, don't contain a valid
partition table. They never will. So I'd like to disable partition
detection, because these messages overflow the kernel message buffer,
depriving syslog of gathering any useful boot messages, and also
needlessly lengthening the boot process. (Of course the noise alone
is disturbing enough when one tries to troubleshoot a boot problem.)
However, looking at the kernel sources didn't give me any hint. Is
this possible to disable at all?
(Please Cc me, I'm not on the list.)
After reading some code, I didn't see any boot or module load options
you can use to prevent that, I think you may want to increase buffer
size to hold the messages and use "grep -v" to create a sanitized
dmesg. If you can give an example of the error message you see I can
look again.
Don't forget to copy the list...
Thanks for looking into this. As an illustration, a reboot looks like
this in the syslog:
Mar 3 17:20:55 mach kernel: Kernel logging (proc) stopped.
Mar 3 17:20:55 mach kernel: Kernel log daemon terminating.
Mar 3 17:20:56 mach exiting on signal 15
Mar 3 17:27:00 mach syslogd 1.4.1#18: restart.
Mar 3 17:27:00 mach kernel: klogd 1.4.1#18, log source = /proc/kmsg started.
[boot messages should have been inserted here.]
Mar 3 17:27:00 mach kernel: Enabled
Mar 3 17:27:00 mach kernel: sdd:<6>sd 0:0:0:3: [sdd] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdd, sector 0
Mar 3 17:27:00 mach kernel: sd 0:0:0:3: [sdd] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdd, sector 0
[the above 3 lines 7 more times]
Mar 3 17:27:00 mach kernel: Dev sdd: unable to read RDB block 0
[those 3 lines 2 more times]
Mar 3 17:27:00 mach kernel: sd 0:0:0:3: [sdd] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdd, sector 24
Mar 3 17:27:00 mach kernel: printk: 29 messages suppressed.
Mar 3 17:27:00 mach kernel: sd 0:0:0:3: [sdd] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdd, sector 24
Mar 3 17:27:00 mach kernel: sd 0:0:0:3: [sdd] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdd, sector 0
Mar 3 17:27:00 mach kernel: unable to read partition table
Mar 3 17:27:00 mach kernel: sd 0:0:0:3: [sdd] Attached SCSI disk
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] 10485760 512-byte hardware sectors (5369 MB)
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] Write Protect is off
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] Cache data unavailable
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] 10485760 512-byte hardware sectors (5369 MB)
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] Write Protect is off
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] Cache data unavailable
Mar 3 17:27:00 mach kernel: sde: unknown partition table
Mar 3 17:27:00 mach kernel: sd 0:0:1:0: [sde] Attached SCSI disk
Mar 3 17:27:00 mach kernel: sd 0:0:1:1: [sdf] 419430400 512-byte hardware sectors (214748 MB)
Mar 3 17:27:00 mach kernel: sd 0:0:1:1: [sdf] Test WP failed, assume Write Enabled
Mar 3 17:27:00 mach kernel: sd 0:0:1:1: [sdf] 419430400 512-byte hardware sectors (214748 MB)
Mar 3 17:27:00 mach kernel: sd 0:0:1:1: [sdf] Test WP failed, assume Write Enabled
Mar 3 17:27:00 mach kernel: sdf:<6>sd 0:0:1:1: [sdf] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdf, sector 0
Mar 3 17:27:00 mach kernel: sd 0:0:1:1: [sdf] Device not ready: <6>: Sense Key : Not Ready [current]
Mar 3 17:27:00 mach kernel: : Add. Sense: Logical unit not ready, manual intervention required
Mar 3 17:27:00 mach kernel: end_request: I/O error, dev sdf, sector 0
[and so on]
It would be possible to grep out the offending lines, but I'd rather
fight the cause than the symptom. Doing my research I realized I'm
not alone with this problem. Looks like a recompilation is necessary,
so I'm turning this into a feature request: how could selective
partition check be added to the Linux kernel? I'm willing to give it
a shot under some expert guidance.
--
Thanks,
Feri.