Re: [PATCH v2] module: Add LZ4 module compression

From
Christophe Leroy (CS GROUP) <chleroy@kernel.org>
Date
2026-11-16 10:28:14
Also in
linux-kbuild, lkml
Reply to
Paul Menzel, 2026-11-15

Le 15/11/2026 à 13:04, Paul Menzel a écrit :
XZ modules are small but slow to decompress in the kernel. Therefore,
support modules compressed in the LZ4 frame format (.ko.lz4), as written
by lz4(1). Decode block by block into a scratch buffer and copy into the
module pages. Linked blocks keep the last 64 KiB of output in front of
the scratch buffer as the dictionary. Verify the header checksum, block
checksums, content checksum and content size when the frame has them.
Frames with a dictionary ID are rejected.
You present your patch as if XZ was the only compress method available, but the kernel has:

kernel/module/Kconfig:config MODULE_COMPRESS_GZIP
kernel/module/Kconfig:config MODULE_COMPRESS_XZ
kernel/module/Kconfig:config MODULE_COMPRESS_ZSTD

Can you provide a comparison of your new proposed compression method with all three already available methods, especially with ZSTD ?

Christophe
quoted hunk ↗ jump to hunk
modules_install uses `lz4 -12 -B4 -BD`: 64 KiB linked blocks are as
small as 4 MiB blocks (i915.ko: 3587140 vs 3585364 bytes) and keep the
scratch buffer at 128 KiB.

Userspace needs kmod with LZ4 support for depmod and modprobe [1].

On a Dell XPS 13 9310 with an Intel Core i7-1165G7 (Tiger Lake) and an
NVMe SSD, decompressing and checking the signatures of the 237 modules
loaded during boot takes 624 ms of CPU time with XZ (i915: 91 ms) and
131 ms with LZ4 (i915: 12 ms), measured by calling finit_module() again
for each loaded module. The LZ4 modules take 20.3 MB instead of 11.0 MB.
Both kernels are v7.4-rc1 with the same patches, including pending
lib/xz decoder speed-ups. Ten alternating boots of each kernel:

   | ms (median)                               |  XZ  | LZ4  | change |
   +-------------------------------------------+------+------+--------+
   | early-i915 (modprobe i915 + dependencies) |  295 |   90 |   -205 |
   | first i915 message                        |  738 |  547 |   -192 |
   | GDM autologin                             |  973 |  876 |    -96 |
   | GRUB start to autologin                   | 1292 | 1197 |    -94 |

QEMU 11.1.2 (KVM, AMD EPYC 7763, 8 vCPUs, module.sig_enforce=1, 10
rounds), loading the same 237 modules in dependency order:

   | median                   |   XZ    |   LZ4   | uncompressed |
   +--------------------------+---------+---------+--------------+
   | one at a time            | 2082 ms | 1499 ms |      1461 ms |
   | 8 in parallel, like udev |  619 ms |  573 ms |       593 ms |

Link: https://github.com/kmod-project/kmod/pull/505 [1]
Signed-off-by: Paul Menzel <redacted>
---

Notes:
     Changes in v2:
     - Declare retval as ssize_t, so output of 2 GiB or more is not
       truncated (Sashiko). The zstd decoder has the same bug, fixed by
       the separate patch "module/decompress: Use ssize_t for the zstd
       decompressed size".
     - Reject empty frames with -EINVAL; v1 failed vmap() of 0 pages with
       -ENOMEM (Sashiko).
     - Describe the decoder and link the frame format specification, group
       the definitions by FLG byte, BD byte and block size field, compare the
       version with FIELD_GET(), rename LZ4F_DICT_SIZE to LZ4F_WINDOW_SIZE,
       look up the block maximum size in a table, shorten the dictionary
       comment (Bradley Morgan).
     
     v1: https://lore.kernel.org/all/20261113144233.193782-1-pmenzel@molgen.mpg.de/ (local)
     
     Claude Opus 5.5 (Claude Code) wrote the decoder, the v2
     changes and this message. Tests: W=1 compile (GCC 16.2, Debian config
     for x86_64, tinyconfig for i386); QEMU with module.sig_enforce=1: 11 LZ4
     frame variants (64 KiB-4 MiB, linked/independent, block/content
     checksums, content size, stored blocks) load, 9 corrupt, truncated or
     empty files are rejected with EINVAL or EKEYREJECTED (v1: ENOMEM for the
     empty ones); the 237-module boot set loads in QEMU. v1 also loaded on a
     Dell XPS 13 9310 (20 boots); v2 was not booted on hardware.

  kernel/module/Kconfig      |  13 +-
  kernel/module/decompress.c | 243 +++++++++++++++++++++++++++++++++++++
  scripts/Makefile.modinst   |   6 +
  3 files changed, 261 insertions(+), 1 deletion(-)
diff --git a/kernel/module/Kconfig b/kernel/module/Kconfig
index 43b1bb01fd273..36f12612c74dd 100644
--- a/kernel/module/Kconfig
+++ b/kernel/module/Kconfig
@@ -344,7 +344,7 @@ config MODULE_COMPRESS
  	  This is fully compatible with signed modules.
  
  	  The tool used to work with modules needs to support the selected
-	  compression type. kmod MAY support gzip, xz and zstd. Other tools
+	  compression type. kmod MAY support gzip, xz, zstd and lz4. Other tools
  	  might have a limited selection of the supported types.
  
  	  Note that for modules inside an initrd or initramfs, it's more
@@ -377,6 +377,15 @@ config MODULE_COMPRESS_ZSTD
  	  Support modules compressed with ZSTD. The installed modules are
  	  suffixed with .ko.zst.
  
+config MODULE_COMPRESS_LZ4
+	bool "LZ4"
+	help
+	  Support modules compressed with LZ4. The installed modules are
+	  suffixed with .ko.lz4.
+
+	  LZ4 modules are larger than XZ or ZSTD ones but decompress
+	  several times faster.
+
  endchoice
  
  config MODULE_COMPRESS_ALL
@@ -394,6 +403,8 @@ config MODULE_DECOMPRESS
  	select ZLIB_INFLATE if MODULE_COMPRESS_GZIP
  	select XZ_DEC if MODULE_COMPRESS_XZ
  	select ZSTD_DECOMPRESS if MODULE_COMPRESS_ZSTD
+	select LZ4_DECOMPRESS if MODULE_COMPRESS_LZ4
+	select XXHASH if MODULE_COMPRESS_LZ4
  	help
  	  Support for decompressing kernel modules by the kernel itself
  	  instead of relying on userspace to perform this task. Useful when
diff --git a/kernel/module/decompress.c b/kernel/module/decompress.c
index cce098671be97..028b411015f21 100644
--- a/kernel/module/decompress.c
+++ b/kernel/module/decompress.c
@@ -287,6 +287,249 @@ static ssize_t module_zstd_decompress(struct load_info *info,
  	kvfree(wksp);
  	return retval;
  }
+#elif defined(CONFIG_MODULE_COMPRESS_LZ4)
+#include <linux/bitfield.h>
+#include <linux/lz4.h>
+#include <linux/sizes.h>
+#include <linux/unaligned.h>
+#include <linux/xxhash.h>
+#define MODULE_COMPRESSION	lz4
+#define MODULE_DECOMPRESS_FN	module_lz4_decompress
+
+/*
+ * Decoder for the LZ4 frame format written by lz4(1), see
+ * https://github.com/lz4/lz4/blob/dev/doc/lz4_Frame_format.md
+ *
+ * Each block is decoded into a scratch buffer and copied into the module
+ * pages. A linked block may reference up to 64 KiB of the output before
+ * it, so that much output is kept in front of the scratch buffer.
+ */
+#define LZ4F_MAGIC		0x184d2204
+
+/* Frame descriptor, FLG byte */
+#define LZ4F_FLG_VERSION	GENMASK(7, 6)
+#define LZ4F_FLG_BLOCK_INDEP	BIT(5)
+#define LZ4F_FLG_BLOCK_CSUM	BIT(4)
+#define LZ4F_FLG_CONTENT_SIZE	BIT(3)
+#define LZ4F_FLG_CONTENT_CSUM	BIT(2)
+#define LZ4F_FLG_RESERVED	BIT(1)
+#define LZ4F_FLG_DICT_ID	BIT(0)
+
+/* Frame descriptor, BD byte */
+#define LZ4F_BD_BLOCK_MAXSIZE	GENMASK(6, 4)
+#define LZ4F_BD_RESERVED	(BIT(7) | GENMASK(3, 0))
+
+/* Block size field: the top bit marks a block stored uncompressed */
+#define LZ4F_BLOCK_UNCOMPRESSED	BIT(31)
+
+#define LZ4F_WINDOW_SIZE	SZ_64K
+
+/* Block maximum sizes for the BD byte's Block MaxSize values 4 to 7 */
+static const u32 lz4f_block_max[] = { SZ_64K, SZ_256K, SZ_1M, SZ_4M };
+
+static int module_lz4_copy_out(struct load_info *info, const u8 *src,
+			       size_t len, size_t *total)
+{
+	while (len) {
+		size_t offset = *total % PAGE_SIZE;
+		size_t chunk = min_t(size_t, len, PAGE_SIZE - offset);
+		struct page *page;
+
+		if (offset)
+			page = info->pages[info->used_pages - 1];
+		else
+			page = module_get_next_page(info);
+		if (IS_ERR(page))
+			return PTR_ERR(page);
+
+		memcpy_to_page(page, offset, src, chunk);
+		src += chunk;
+		len -= chunk;
+		*total += chunk;
+	}
+
+	return 0;
+}
+
+static int module_lz4_verify_content(struct load_info *info, size_t total,
+				     u32 expected)
+{
+	void *data;
+	u32 csum;
+
+	data = vmap(info->pages, info->used_pages, VM_MAP, PAGE_KERNEL_RO);
+	if (!data)
+		return -ENOMEM;
+	csum = xxh32(data, total, 0);
+	vunmap(data);
+
+	if (csum != expected) {
+		pr_err("LZ4-compressed data is corrupt (content checksum)\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static ssize_t module_lz4_decompress(struct load_info *info,
+				     const void *buf, size_t size)
+{
+	const u8 *in = buf, *end = in + size, *desc;
+	size_t block_max, total = 0, dict_len = 0;
+	u64 content_size = 0;
+	u8 *scratch, *out;
+	bool linked;
+	u8 flg, bd;
+	ssize_t retval;
+
+	if (size < 7 || get_unaligned_le32(in) != LZ4F_MAGIC) {
+		pr_err("not an lz4 compressed module\n");
+		return -EINVAL;
+	}
+
+	desc = in + 4;
+	flg = desc[0];
+	bd = desc[1];
+	in = desc + 2;
+	if (FIELD_GET(LZ4F_FLG_VERSION, flg) != 1 ||
+	    (flg & LZ4F_FLG_RESERVED) || (bd & LZ4F_BD_RESERVED) ||
+	    FIELD_GET(LZ4F_BD_BLOCK_MAXSIZE, bd) < 4) {
+		pr_err("LZ4-compressed data has an unsupported frame descriptor\n");
+		return -EINVAL;
+	}
+	if (flg & LZ4F_FLG_DICT_ID) {
+		pr_err("LZ4-compressed data needs a dictionary\n");
+		return -EINVAL;
+	}
+	if (flg & LZ4F_FLG_CONTENT_SIZE) {
+		if (end - in < 8)
+			goto truncated_header;
+		content_size = get_unaligned_le64(in);
+		in += 8;
+	}
+	if (end - in < 1)
+		goto truncated_header;
+	if (*in != ((xxh32(desc, in - desc, 0) >> 8) & 0xff)) {
+		pr_err("LZ4-compressed data has a corrupt frame descriptor\n");
+		return -EINVAL;
+	}
+	in++;
+
+	block_max = lz4f_block_max[FIELD_GET(LZ4F_BD_BLOCK_MAXSIZE, bd) - 4];
+	linked = !(flg & LZ4F_FLG_BLOCK_INDEP);
+
+	scratch = kvmalloc((linked ? LZ4F_WINDOW_SIZE : 0) + block_max,
+			   GFP_KERNEL);
+	if (!scratch)
+		return -ENOMEM;
+	out = scratch + (linked ? LZ4F_WINDOW_SIZE : 0);
+
+	for (;;) {
+		u32 block_size;
+		size_t len;
+		int ret;
+
+		if (end - in < 4)
+			goto truncated;
+		block_size = get_unaligned_le32(in);
+		in += 4;
+		if (!block_size)
+			break;
+
+		len = block_size & ~LZ4F_BLOCK_UNCOMPRESSED;
+		if (len > block_max) {
+			pr_err("LZ4-compressed data has an oversized block\n");
+			retval = -EINVAL;
+			goto out;
+		}
+		if ((size_t)(end - in) < len +
+		    (flg & LZ4F_FLG_BLOCK_CSUM ? 4 : 0))
+			goto truncated;
+
+		if ((flg & LZ4F_FLG_BLOCK_CSUM) &&
+		    xxh32(in, len, 0) != get_unaligned_le32(in + len)) {
+			pr_err("LZ4-compressed data is corrupt (block checksum)\n");
+			retval = -EINVAL;
+			goto out;
+		}
+
+		if (block_size & LZ4F_BLOCK_UNCOMPRESSED) {
+			memcpy(out, in, len);
+			ret = len;
+		} else if (linked) {
+			ret = LZ4_decompress_safe_usingDict(in, out, len,
+							    block_max,
+							    out - dict_len,
+							    dict_len);
+		} else {
+			ret = LZ4_decompress_safe(in, out, len, block_max);
+		}
+		if (ret < 0) {
+			pr_err("LZ4-decompression failed\n");
+			retval = -EINVAL;
+			goto out;
+		}
+
+		retval = module_lz4_copy_out(info, out, ret, &total);
+		if (retval)
+			goto out;
+
+		if (linked) {
+			/* Keep the last 64 KiB as the next block's dictionary. */
+			size_t keep = min_t(size_t, dict_len + ret,
+					    LZ4F_WINDOW_SIZE);
+
+			memmove(out - keep, out + ret - keep, keep);
+			dict_len = keep;
+		}
+
+		in += len;
+		if (flg & LZ4F_FLG_BLOCK_CSUM)
+			in += 4;
+	}
+
+	if (!total) {
+		pr_err("LZ4-compressed module is empty\n");
+		retval = -EINVAL;
+		goto out;
+	}
+
+	if (flg & LZ4F_FLG_CONTENT_CSUM) {
+		if (end - in < 4)
+			goto truncated;
+		retval = module_lz4_verify_content(info, total,
+						   get_unaligned_le32(in));
+		if (retval)
+			goto out;
+		in += 4;
+	}
+
+	if (in != end) {
+		pr_err("LZ4-compressed module has trailing data\n");
+		retval = -EINVAL;
+		goto out;
+	}
+
+	if ((flg & LZ4F_FLG_CONTENT_SIZE) && content_size != total) {
+		pr_err("LZ4-compressed data has a wrong content size\n");
+		retval = -EINVAL;
+		goto out;
+	}
+
+	retval = total;
+	goto out;
+
+truncated:
+	pr_err("LZ4-compressed data is truncated\n");
+	retval = -EINVAL;
+out:
+	kvfree(scratch);
+	return retval;
+
+truncated_header:
+	pr_err("LZ4-compressed data is truncated\n");
+	return -EINVAL;
+}
  #else
  #error "Unexpected configuration for CONFIG_MODULE_DECOMPRESS"
  #endif
diff --git a/scripts/Makefile.modinst b/scripts/Makefile.modinst
index 9ba45e5b32b18..aebc5e89d0e75 100644
--- a/scripts/Makefile.modinst
+++ b/scripts/Makefile.modinst
@@ -57,6 +57,7 @@ ifdef CONFIG_MODULE_COMPRESS_ALL
  suffix-$(CONFIG_MODULE_COMPRESS_GZIP)	:= .gz
  suffix-$(CONFIG_MODULE_COMPRESS_XZ)	:= .xz
  suffix-$(CONFIG_MODULE_COMPRESS_ZSTD)	:= .zst
+suffix-$(CONFIG_MODULE_COMPRESS_LZ4)	:= .lz4
  endif
  
  modules := $(patsubst %.o, $(dst)/%.ko$(suffix-y), $(modules))
@@ -151,6 +152,8 @@ quiet_cmd_xz = XZ      $@
        cmd_xz = $(XZ) --check=crc32 --lzma2=dict=1MiB -f $<
  quiet_cmd_zstd = ZSTD    $@
        cmd_zstd = $(ZSTD) --rm -f -q $<
+quiet_cmd_lz4 = LZ4     $@
+      cmd_lz4 = $(LZ4) -12 -B4 -BD --rm -f -q $< $@
  
  $(dst)/%.ko.gz: $(dst)/%.ko FORCE
  	$(call cmd,gzip)
@@ -161,6 +164,9 @@ $(dst)/%.ko.xz: $(dst)/%.ko FORCE
  $(dst)/%.ko.zst: $(dst)/%.ko FORCE
  	$(call cmd,zstd)
  
+$(dst)/%.ko.lz4: $(dst)/%.ko FORCE
+	$(call cmd,lz4)
+
  PHONY += FORCE
  FORCE:
  
  
Thread (5 messages) 5 messages, 3 authors, last reply 14h ago
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help