On Thu, Dec 07, 2017 at 09:50:23AM +0100, Miklos Szeredi wrote:

On Thu, Dec 7, 2017 at 5:14 AM, Fengguang Wu [off-list ref] wrote:

quoted

CC fuse maintainer, too.

On Wed, Dec 06, 2017 at 05:09:27PM -0800, Andrew Morton wrote:

quoted

On Fri, 1 Dec 2017 13:29:28 +0100 Jan Kara [off-list ref] wrote:

quoted

On Thu 30-11-17 14:15:58, Andrew Morton wrote:

quoted

From: Maxim Patlasov <redacted>
Subject: mm: add strictlimit knob

The "strictlimit" feature was introduced to enforce per-bdi dirty
limits
for FUSE which sets bdi max_ratio to 1% by default:

http://article.gmane.org/gmane.linux.kernel.mm/105809

However the feature can be useful for other relatively slow or
untrusted
BDIs like USB flash drives and DVD+RW.  The patch adds a knob to enable
the feature:

echo 1 > /sys/class/bdi/X:Y/strictlimit

Being enabled, the feature enforces bdi max_ratio limit even if global
(10%) dirty limit is not reached.  Of course, the effect is not visible
until /sys/class/bdi/X:Y/max_ratio is decreased to some reasonable
value.

In principle I have nothing against this and the usecase sounds
reasonable
(in fact I believe the lack of a feature like this is one of reasons why
desktop automounters usually mount USB devices with 'sync' mount option).
So feel free to add:

Reviewed-by: Jan Kara <jack@suse.cz>

Cc Jens, who may be vaguely interested in plans to finally merge this
three-year-old patch?



From: Maxim Patlasov <redacted>
Subject: mm: add strictlimit knob

The "strictlimit" feature was introduced to enforce per-bdi dirty limits
for FUSE which sets bdi max_ratio to 1% by default:

http://article.gmane.org/gmane.linux.kernel.mm/105809

That link is invalid for now, possibly due to the gmane site rebuild.
I find an email thread here which looks relevant:

https://sourceforge.net/p/fuse/mailman/message/35254883/

Where Maxim has an interesting point:

       > Did any one try increasing the limit and did see any better/worse

quoted

performance ?

       We've used 20% as default value in OpenVZ kernel for a long while (1%
was not enough to saturate our distributed parallel storage).

So the knob will also enable people to _disable_ the 1% fuse limit to
increase performance.

So people can use the exposed knob in 2 ways to fit their needs, which
is in general a good thing.

However the comment in wb_position_ratio() says

                       Without strictlimit feature, fuse writeback may
         * consume arbitrary amount of RAM because it is accounted in
         * NR_WRITEBACK_TEMP which is not involved in calculating
"nr_dirty".

How dangerous would that be if some user disabled the 1% fuse limit
through the exposed knob? Will the NR_WRITEBACK_TEMP effect go far
beyond the user's expectation (20% max dirty limit)?

Looking at the fuse code, NR_WRITEBACK_TEMP will grow proportional to
WB_WRITEBACK, which should be throttled when bdi_write_congested().
The congested flag will be set on

       fuse_conn.num_background >= fuse_conn.congestion_threshold
       So it looks NR_WRITEBACK_TEMP will somehow be throttled. Just that
it's not included in the 20% dirty limit.

Only balance_dirty_pages_ratelimited() is going to limit the
generation of dirty pages, I don't think congestion flags will do
that.

Right. However my concern is something to limit the generation of
fuse's _writeback_ pages.

The normal writeback pages are limited in 2 ways:

- balance_dirty_pages_ratelimited()'s dirty throttling:

  nr_dirty + nr_writeback + nr_unstable < global and/or bdi dirty limit

- block layer's nr_requests queue limit

However fuse's NR_WRITEBACK_TEMP looks special and has none of such
limits. The congested bit merely affect the vmscan pageout path.

        pageout
          may_write_to_inode
            inode_write_congested
              wb_congested

I wonder if fuse has its own approach to limit NR_WRITEBACK_TEMP?
Either explicitly or implicitly, there has to be some hard limit.

And (AFAICS) for fuse only  BDI_CAP_STRICTLIMIT will allow
accounting temp writeback pages when throttling dirty page generation.
So without BDI_CAP_STRICTLIMIT kernel memory use of fuse may explode.
So we probably need a way to force BDI_CAP_STRICTLIMIT (i.e. do not
permit disabling it for fuse).

So fuse relies on small nr_dirty. Does fuse impose any explicit or
implicit rule that NR_WRITEBACK_TEMP will never exceed (N * nr_dirty)?
Otherwise the size of NR_WRITEBACK_TEMP cannot be guaranteed.

For example, is it possible for some process (eg. dd) to dirty pages
as fast as possible while some other kernel logic to convert PG_dirty
to NR_WRITEBACK_TEMP as fast as possible, so that even the 1% bdi
strictlimit (which limits PG_dirty rather than NR_WRITEBACK_TEMP)
cannot stop all memory being eat up by ever growing NR_WRITEBACK_TEMP?

Thanks,
Fengguang

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>