On Thursday, November 29, 2012 04:17:19 PM Toshi Kani wrote:

On Thu, 2012-11-29 at 23:11 +0100, Rafael J. Wysocki wrote:

quoted

On Thursday, November 29, 2012 02:46:44 PM Toshi Kani wrote:

quoted

On Thu, 2012-11-29 at 22:23 +0100, Rafael J. Wysocki wrote:

quoted

On Thursday, November 29, 2012 01:38:39 PM Toshi Kani wrote:

Well, let's put it this way: If we started a trim, we should just do it
completely, in which case we know we can go for the eject, or we should
roll it back completely.  Now, if you just break the trim on first error,
the complete rollback is kind of problematic.  It should be doable, but
it won't be easy.  On the other hand, if you go for the full trim,
doing a rollback is trivial, it's as though you have reinserted the whole
stuff.

acpi_bus_check_add() skips initialization when an ACPI device already
has its associated acpi_device.  So, I think it works either way.

OK

quoted

quoted

Now, that need not harm functionality, and that's why I proposed the
eject_forbidden flag, so that .remove() can say "I'm not done, please
rollback", in which case the device can happily function going forward,
even if we don't rebind the driver to it.

A partially trimmed acpi_device is hard to rollback.  acpi_device should
be either trimmed completely or intact.

I may or may not agree, depending on what you mean by "trimmed". :-)

quoted

When a function failed to trim
an acpi_device, it needs to rollback its operation for the device before
returning an error.

Unless it is .remove(), because .remove() is supposed to always succeed
(ie. unbind the driver from the device).  However, it may signal the caller
that something's fishy, by setting a flag in the device object, for example.

Right, .remove() cannot fail.  We still need to check if we should
continue to use .remove(), though.

As for the flag, are you thinking that we call acpi_bus_trim() with
rmdevice false first, so that it won't remove acpi_device?

I'm not sure if that's going to help.

Definitely, .remove() should just unbind the driver from the device.
That's what it's supposed to do.  Still, it may leave some information for
the caller in the device structure itself.  For example, "I have unbound
from the device, but it is not safe to remove it physically".

I'm now thinking that we may need to rework the trimming so that
.remove() is called for all drivers first and the struct acpi_device
objects are not removed at this stage.  Then, if .remove() from one
driver signals the situation like above, the routine will have to
rebind the drivers that have been unbound and we're done.

After that stage, when all drivers have been unbound, we should be
able to go for full eject.  First, we can drop all struct acpi_device
objects in the relevant subtree and then we can run _EJ0.

quoted

quoted

This is because only the failed function has enough
context to rollback when an error occurred in the middle of its
procedure.

Not really.  If it actually removes the struct acpi_device then the caller
may run acpi_bus_scan() on that device if necessary.  There may be a problem
if the device has an associated physical node (or more of them), but that
requires special care anyway.

Well, hot-remove to a device fails when there is a reason to fail.  IOW,
such reason prevented the device to be removed safely.  So, I think we
need to put it back to the original state in this case.  Removing it by
ignoring the cause of failure sounds unsafe to me.  Some status/data may
be left un-deleted as a result.

Again, I may or may not agree with that, depending on whether you're talking
about physical devices or about struct acpi_device objects.

Anyway, I agree that removing struct acpi_device objects may not be worth the
effort if we're going to re-create them in a while, because that may be costly.

Thanks,
Rafael


-- 
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org.  For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"dont@kvack.org"> email@kvack.org </a>