>
 > Also when I plugged it in, it sat there for about 10 seconds before
 > finishing loading (dmesg printed another 5 lines about the device
 > after about 10 seconds), but still no tuning.

 Can I see those five lines?  ;-)

 While you're at it, you may as well include dmesg from the point that the bridge driver loads and on.

Here's dmesg from the point it starts up until it finishes printing stuff.

usb 2-10: new high speed USB device using ehci_hcd and address 22
usb 2-10: configuration #1 chosen from 1 choice
af9015_usb_probe:
af9015_identify_state: reply:01
dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in cold state, will
try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
af9015_download_firmware:
dvb-usb: found a 'Leadtek Winfast DTV Dongle Gold' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek Winfast DTV Dongle Gold)
af9015_eeprom_dump:
00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02
10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30
20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff
30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff
40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff
50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00
60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00
70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00
80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00
90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00
a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00
b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff
c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
af9015_read_config: xtal:2 set adc_clock:28000
af9015_read_config: tuner id1:156
af9015_read_config: spectral inversion:0
af9015_set_gpios:
af9013: firmware version:4.95.0
DVB: registering frontend 2 (Afatech AF9013 DVB-T)...
af9015_tuner_attach:
tda18271_tuner_attach:
tda18271 5-00c0: creating new instance
TDA18271HD/C1 detected @ 5-00c0
input: IR-receiver inside an USB DVB receiver as /class/input/input34
dvb-usb: schedule remote query interval to 200 msecs.
dvb-usb: Leadtek Winfast DTV Dongle Gold successfully initialized and connected.
af9015_init:
af9015_download_ir_table:
input: Leadtek WinFast DTV Dongle Gold as /class/input/input35
input: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on
usb-0000:00:02.1-10

 You said that you tuned to "channel 7, sydney, australia" -- is that an 8 MHz channel?  What frequency is it on?

This is channel 7's entry in channels.conf:
7 Digital:177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_2_3:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE:513:514:1312

Jarryd.

_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb