Hi,
Thank you for your patches.
On 3/10/20 2:17 PM, Dmitry Mastykin wrote:
KEY_LEFTMETA is assigned to the first touch-key (it will be the default
keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned to other touch-keys.
One may assign any keycodes via HWDB.
I think the commit message could use some work, e.g. something like this:
###
Subj: Input: goodix - Add support for more then one touch-key
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
###
Previous press/release behavior has changed.
Before: both press/release events were generated on key touch.
Now: press/release events correspond to real touch and release now.
Looking at the old code I do not think that this is correct,
the old code keeps reporting KEY_LEFTMETA as pressed as long as
the GOODIX_HAVE_KEY is set. I guess the undesirable behavior you
describe here was the result of an earlier version of your
patch to support more then one touch key.
Signed-off-by: Dmitry Mastykin <redacted>
Other then the remarks about the commit message this looks
good to me.
Regards,
Hans
quoted hunk
---
drivers/input/touchscreen/goodix.c | 54 ++++++++++++++++++++++++------
1 file changed, 44 insertions(+), 10 deletions(-)
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index fdec508..6a7ecc6 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -38,6 +38,7 @@
#define GOODIX_CONTACT_SIZE 8
#define GOODIX_MAX_CONTACT_SIZE 9
#define GOODIX_MAX_CONTACTS 10
+#define GOODIX_MAX_KEYS 7
#define GOODIX_CONFIG_MIN_LENGTH 186
#define GOODIX_CONFIG_911_LENGTH 186
@@ -55,6 +56,7 @@
#define GOODIX_REG_ID 0x8140
#define GOODIX_BUFFER_STATUS_READY BIT(7)
+#define GOODIX_HAVE_KEY BIT(4)
#define GOODIX_BUFFER_STATUS_TIMEOUT 20
#define RESOLUTION_LOC 1
@@ -100,6 +102,7 @@ struct goodix_ts_data {
enum goodix_irq_pin_access_method irq_pin_access_method;
unsigned int contact_size;
u8 config[GOODIX_CONFIG_MAX_LENGTH];
+ unsigned short keymap[GOODIX_MAX_KEYS];
};
static int goodix_check_cfg_8(struct goodix_ts_data *ts,@@ -285,8 +288,14 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
*/
max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT);
do {
+ /*
+ * We are going to read ts->contact_size * max(1, touch_num) + 2
+ * bytes, where + 2 consists of reading 1 extra byte for the
+ * header + 1 extra byte for the footer which contains the
+ * touch-key code.
+ */
error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR,
- data, ts->contact_size + 1);
+ data, ts->contact_size + 2);
if (error) {
dev_err(&ts->client->dev, "I2C transfer error: %d\n",
error);@@ -299,10 +308,10 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
return -EPROTO;
if (touch_num > 1) {
- data += 1 + ts->contact_size;
+ data += 2 + ts->contact_size;
error = goodix_i2c_read(ts->client,
GOODIX_READ_COOR_ADDR +
- 1 + ts->contact_size,
+ 2 + ts->contact_size,
data,
ts->contact_size *
(touch_num - 1));@@ -353,6 +362,23 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
}
+static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data)
+{
+ int touch_num;
+ u8 key_value;
+ int i;
+
+ if (data[0] & GOODIX_HAVE_KEY) {
+ touch_num = data[0] & 0x0f;
+ key_value = data[1 + ts->contact_size * touch_num];
+ for (i = 0; i < GOODIX_MAX_KEYS; ++i)
+ if (key_value & (1 << i))
+ input_report_key(ts->input_dev, ts->keymap[i], 1);
+ } else
+ for (i = 0; i < GOODIX_MAX_KEYS; ++i)
+ input_report_key(ts->input_dev, ts->keymap[i], 0);
+}
+
/**
* goodix_process_events - Process incoming events
*@@ -363,7 +389,7 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
*/
static void goodix_process_events(struct goodix_ts_data *ts)
{
- u8 point_data[1 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
+ u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
int touch_num;
int i;
@@ -371,11 +397,7 @@ static void goodix_process_events(struct goodix_ts_data *ts)
if (touch_num < 0)
return;
- /*
- * Bit 4 of the first byte reports the status of the capacitive
- * Windows/Home button.
- */
- input_report_key(ts->input_dev, KEY_LEFTMETA, point_data[0] & BIT(4));
+ goodix_ts_report_key(ts, point_data);
for (i = 0; i < touch_num; i++)
if (ts->contact_size == 9)
@@ -961,6 +983,7 @@ static int goodix_i2c_test(struct i2c_client *client)
static int goodix_configure_dev(struct goodix_ts_data *ts)
{
int error;
+ int i;
ts->int_trigger_type = GOODIX_INT_TRIGGER;
ts->max_touch_num = GOODIX_MAX_CONTACTS;@@ -978,8 +1001,19 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
ts->input_dev->id.product = ts->id;
ts->input_dev->id.version = ts->version;
+ ts->input_dev->keycode = ts->keymap;
+ ts->input_dev->keycodesize = sizeof(ts->keymap[0]);
+ ts->input_dev->keycodemax = GOODIX_MAX_KEYS;
+
/* Capacitive Windows/Home button on some devices */
- input_set_capability(ts->input_dev, EV_KEY, KEY_LEFTMETA);
+ for (i = 0; i < GOODIX_MAX_KEYS; ++i) {
+ if (i == 0)
+ ts->keymap[i] = KEY_LEFTMETA;
+ else
+ ts->keymap[i] = KEY_F1 + (i - 1);
+
+ input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]);
+ }
input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X);
input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y);
Hi Hans,
thank you for the suggested ideas for the patches, reviewing them, and
for suggested commit message in the last mail.
Should I change patch to v2 after correcting the commit message?
>> Previous press/release behavior has changed.
>> Before: both press/release events were generated on key touch.
>> Now: press/release events correspond to real touch and release now.
>
> Looking at the old code I do not think that this is correct,
> the old code keeps reporting KEY_LEFTMETA as pressed as long as
> the GOODIX_HAVE_KEY is set. I guess the undesirable behavior you
> describe here was the result of an earlier version of your
> patch to support more then one touch key.
>
I've just tested the old code: it has wrong behavior. And the patch 2/2
("Input: goodix - Ignore spurious interrupts", 2020-03-10) makes it correct.
Kind regards
Dmitry Mastykin
On 3/10/20 5:40 PM, Hans de Goede wrote:
> Hi,
>
> Thank you for your patches.
>
> On 3/10/20 2:17 PM, Dmitry Mastykin wrote:
>> KEY_LEFTMETA is assigned to the first touch-key (it will be the default
>> keycode for devices with a single touch-key).
>> KEY_F1, KEY_F2... are assigned to other touch-keys.
>> One may assign any keycodes via HWDB.
>
> I think the commit message could use some work, e.g. something like this:
>
> ###
>
> Subj: Input: goodix - Add support for more then one touch-key
>
> Some devices with a goodix touchscreen have more then 1 capacitive
> touch-key. This commit replaces the current support for a single
> touch-key, which ignored the reported key-code. With support for
> up to 7 touch-keys, based upon checking the key-code which is
> post-fixed to any reported touch-data.
>
> KEY_LEFTMETA is assigned to the first touch-key (it will still be
> the default keycode for devices with a single touch-key).
> KEY_F1, KEY_F2... are assigned as default keycode for the other
> touch-keys.
>
> This commit also add supports for keycode remapping, so that
> systemd-udev's hwdb can be used to remap the codes to send
> keycodes to match the icons on the buttons for devices with more
> then 1 touch-key.
>
> ###
>
>> Previous press/release behavior has changed.
>> Before: both press/release events were generated on key touch.
>> Now: press/release events correspond to real touch and release now.
>
> Looking at the old code I do not think that this is correct,
> the old code keeps reporting KEY_LEFTMETA as pressed as long as
> the GOODIX_HAVE_KEY is set. I guess the undesirable behavior you
> describe here was the result of an earlier version of your
> patch to support more then one touch key.
>
>> Signed-off-by: Dmitry Mastykin [off-list ref]
>
> Other then the remarks about the commit message this looks
> good to me.
>
> Regards,
>
> Hans
>
>
>> ---
>> drivers/input/touchscreen/goodix.c | 54 ++++++++++++++++++++++++------
>> 1 file changed, 44 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/input/touchscreen/goodix.c
b/drivers/input/touchscreen/goodix.c
>> index fdec508..6a7ecc6 100644
>> --- a/drivers/input/touchscreen/goodix.c
>> +++ b/drivers/input/touchscreen/goodix.c
>> @@ -38,6 +38,7 @@
>> #define GOODIX_CONTACT_SIZE 8
>> #define GOODIX_MAX_CONTACT_SIZE 9
>> #define GOODIX_MAX_CONTACTS 10
>> +#define GOODIX_MAX_KEYS 7
>> #define GOODIX_CONFIG_MIN_LENGTH 186
>> #define GOODIX_CONFIG_911_LENGTH 186
>> @@ -55,6 +56,7 @@
>> #define GOODIX_REG_ID 0x8140
>> #define GOODIX_BUFFER_STATUS_READY BIT(7)
>> +#define GOODIX_HAVE_KEY BIT(4)
>> #define GOODIX_BUFFER_STATUS_TIMEOUT 20
>> #define RESOLUTION_LOC 1
>> @@ -100,6 +102,7 @@ struct goodix_ts_data {
>> enum goodix_irq_pin_access_method irq_pin_access_method;
>> unsigned int contact_size;
>> u8 config[GOODIX_CONFIG_MAX_LENGTH];
>> + unsigned short keymap[GOODIX_MAX_KEYS];
>> };
>> static int goodix_check_cfg_8(struct goodix_ts_data *ts,
>> @@ -285,8 +288,14 @@ static int goodix_ts_read_input_report(struct
goodix_ts_data *ts, u8 *data)
>> */
>> max_timeout = jiffies +
msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT);
>> do {
>> + /*
>> + * We are going to read ts->contact_size * max(1,
touch_num) + 2
>> + * bytes, where + 2 consists of reading 1 extra byte for the
>> + * header + 1 extra byte for the footer which contains the
>> + * touch-key code.
>> + */
>> error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR,
>> - data, ts->contact_size + 1);
>> + data, ts->contact_size + 2);
>> if (error) {
>> dev_err(&ts->client->dev, "I2C transfer error: %d\n",
>> error);
>> @@ -299,10 +308,10 @@ static int goodix_ts_read_input_report(struct
goodix_ts_data *ts, u8 *data)
>> return -EPROTO;
>> if (touch_num > 1) {
>> - data += 1 + ts->contact_size;
>> + data += 2 + ts->contact_size;
>> error = goodix_i2c_read(ts->client,
>> GOODIX_READ_COOR_ADDR +
>> - 1 + ts->contact_size,
>> + 2 + ts->contact_size,
>> data,
>> ts->contact_size *
>> (touch_num - 1));
>> @@ -353,6 +362,23 @@ static void goodix_ts_report_touch_9b(struct
goodix_ts_data *ts, u8 *coor_data)
>> input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
>> }
>> +static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data)
>> +{
>> + int touch_num;
>> + u8 key_value;
>> + int i;
>> +
>> + if (data[0] & GOODIX_HAVE_KEY) {
>> + touch_num = data[0] & 0x0f;
>> + key_value = data[1 + ts->contact_size * touch_num];
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i)
>> + if (key_value & (1 << i))
>> + input_report_key(ts->input_dev, ts->keymap[i], 1);
>> + } else
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i)
>> + input_report_key(ts->input_dev, ts->keymap[i], 0);
>> +}
>> +
>> /**
>> * goodix_process_events - Process incoming events
>> *
>> @@ -363,7 +389,7 @@ static void goodix_ts_report_touch_9b(struct
goodix_ts_data *ts, u8 *coor_data)
>> */
>> static void goodix_process_events(struct goodix_ts_data *ts)
>> {
>> - u8 point_data[1 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
>> + u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
>> int touch_num;
>> int i;
>> @@ -371,11 +397,7 @@ static void goodix_process_events(struct
goodix_ts_data *ts)
>> if (touch_num < 0)
>> return;
>> - /*
>> - * Bit 4 of the first byte reports the status of the capacitive
>> - * Windows/Home button.
>> - */
>> - input_report_key(ts->input_dev, KEY_LEFTMETA, point_data[0] &
BIT(4));
>> + goodix_ts_report_key(ts, point_data);
>> for (i = 0; i < touch_num; i++)
>> if (ts->contact_size == 9)
>> @@ -961,6 +983,7 @@ static int goodix_i2c_test(struct i2c_client
*client)
>> static int goodix_configure_dev(struct goodix_ts_data *ts)
>> {
>> int error;
>> + int i;
>> ts->int_trigger_type = GOODIX_INT_TRIGGER;
>> ts->max_touch_num = GOODIX_MAX_CONTACTS;
>> @@ -978,8 +1001,19 @@ static int goodix_configure_dev(struct
goodix_ts_data *ts)
>> ts->input_dev->id.product = ts->id;
>> ts->input_dev->id.version = ts->version;
>> + ts->input_dev->keycode = ts->keymap;
>> + ts->input_dev->keycodesize = sizeof(ts->keymap[0]);
>> + ts->input_dev->keycodemax = GOODIX_MAX_KEYS;
>> +
>> /* Capacitive Windows/Home button on some devices */
>> - input_set_capability(ts->input_dev, EV_KEY, KEY_LEFTMETA);
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i) {
>> + if (i == 0)
>> + ts->keymap[i] = KEY_LEFTMETA;
>> + else
>> + ts->keymap[i] = KEY_F1 + (i - 1);
>> +
>> + input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]);
>> + }
>> input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X);
>> input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y);
>>
>
Hi,
On 3/10/20 4:29 PM, Dmitry Mastykin wrote:
Hi Hans,
thank you for the suggested ideas for the patches, reviewing them, and for suggested commit message in the last mail.
You're welcome.
Should I change patch to v2 after correcting the commit message?
Yes the normal way to do this is to use:
git send-email --subject-prefix="PATCH v2" ...
When sending and add a changelog to the commit message after your
Signed-off-by, like this:
Signed-off-by: ...
---
Changes in v2:
- Improve commit message
When Dmitry Torokhov then applies these patches, git am will
automatically remove the changelog (which is mainly for reviewing
purposes) because it ignores everything after the first '---' line.
Regards,
Hans
>> Previous press/release behavior has changed.
>> Before: both press/release events were generated on key touch.
>> Now: press/release events correspond to real touch and release now.
>
> Looking at the old code I do not think that this is correct,
> the old code keeps reporting KEY_LEFTMETA as pressed as long as
> the GOODIX_HAVE_KEY is set. I guess the undesirable behavior you
> describe here was the result of an earlier version of your
> patch to support more then one touch key.
>
I've just tested the old code: it has wrong behavior. And the patch 2/2 ("Input: goodix - Ignore spurious interrupts", 2020-03-10) makes it correct.
Ah ok, that explains. Well then this bit should probably go to the
commit message of 2/2, since the problem will still exist after 1/2, right?
Kind regards
Dmitry Mastykin
On 3/10/20 5:40 PM, Hans de Goede wrote:
> Hi,
>
> Thank you for your patches.
>
> On 3/10/20 2:17 PM, Dmitry Mastykin wrote:
>> KEY_LEFTMETA is assigned to the first touch-key (it will be the default
>> keycode for devices with a single touch-key).
>> KEY_F1, KEY_F2... are assigned to other touch-keys.
>> One may assign any keycodes via HWDB.
>
> I think the commit message could use some work, e.g. something like this:
>
> ###
>
> Subj: Input: goodix - Add support for more then one touch-key
>
> Some devices with a goodix touchscreen have more then 1 capacitive
> touch-key. This commit replaces the current support for a single
> touch-key, which ignored the reported key-code. With support for
> up to 7 touch-keys, based upon checking the key-code which is
> post-fixed to any reported touch-data.
>
> KEY_LEFTMETA is assigned to the first touch-key (it will still be
> the default keycode for devices with a single touch-key).
> KEY_F1, KEY_F2... are assigned as default keycode for the other
> touch-keys.
>
> This commit also add supports for keycode remapping, so that
> systemd-udev's hwdb can be used to remap the codes to send
> keycodes to match the icons on the buttons for devices with more
> then 1 touch-key.
>
> ###
>
>> Previous press/release behavior has changed.
>> Before: both press/release events were generated on key touch.
>> Now: press/release events correspond to real touch and release now.
>
> Looking at the old code I do not think that this is correct,
> the old code keeps reporting KEY_LEFTMETA as pressed as long as
> the GOODIX_HAVE_KEY is set. I guess the undesirable behavior you
> describe here was the result of an earlier version of your
> patch to support more then one touch key.
>
>> Signed-off-by: Dmitry Mastykin [off-list ref]
>
> Other then the remarks about the commit message this looks
> good to me.
>
> Regards,
>
> Hans
>
>
>> ---
>> drivers/input/touchscreen/goodix.c | 54 ++++++++++++++++++++++++------
>> 1 file changed, 44 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
>> index fdec508..6a7ecc6 100644
>> --- a/drivers/input/touchscreen/goodix.c
>> +++ b/drivers/input/touchscreen/goodix.c
>> @@ -38,6 +38,7 @@
>> #define GOODIX_CONTACT_SIZE 8
>> #define GOODIX_MAX_CONTACT_SIZE 9
>> #define GOODIX_MAX_CONTACTS 10
>> +#define GOODIX_MAX_KEYS 7
>> #define GOODIX_CONFIG_MIN_LENGTH 186
>> #define GOODIX_CONFIG_911_LENGTH 186
>> @@ -55,6 +56,7 @@
>> #define GOODIX_REG_ID 0x8140
>> #define GOODIX_BUFFER_STATUS_READY BIT(7)
>> +#define GOODIX_HAVE_KEY BIT(4)
>> #define GOODIX_BUFFER_STATUS_TIMEOUT 20
>> #define RESOLUTION_LOC 1
>> @@ -100,6 +102,7 @@ struct goodix_ts_data {
>> enum goodix_irq_pin_access_method irq_pin_access_method;
>> unsigned int contact_size;
>> u8 config[GOODIX_CONFIG_MAX_LENGTH];
>> + unsigned short keymap[GOODIX_MAX_KEYS];
>> };
>> static int goodix_check_cfg_8(struct goodix_ts_data *ts,
>> @@ -285,8 +288,14 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
>> */
>> max_timeout = jiffies + msecs_to_jiffies(GOODIX_BUFFER_STATUS_TIMEOUT);
>> do {
>> + /*
>> + * We are going to read ts->contact_size * max(1, touch_num) + 2
>> + * bytes, where + 2 consists of reading 1 extra byte for the
>> + * header + 1 extra byte for the footer which contains the
>> + * touch-key code.
>> + */
>> error = goodix_i2c_read(ts->client, GOODIX_READ_COOR_ADDR,
>> - data, ts->contact_size + 1);
>> + data, ts->contact_size + 2);
>> if (error) {
>> dev_err(&ts->client->dev, "I2C transfer error: %d\n",
>> error);
>> @@ -299,10 +308,10 @@ static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
>> return -EPROTO;
>> if (touch_num > 1) {
>> - data += 1 + ts->contact_size;
>> + data += 2 + ts->contact_size;
>> error = goodix_i2c_read(ts->client,
>> GOODIX_READ_COOR_ADDR +
>> - 1 + ts->contact_size,
>> + 2 + ts->contact_size,
>> data,
>> ts->contact_size *
>> (touch_num - 1));
>> @@ -353,6 +362,23 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
>> input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, input_w);
>> }
>> +static void goodix_ts_report_key(struct goodix_ts_data *ts, u8 *data)
>> +{
>> + int touch_num;
>> + u8 key_value;
>> + int i;
>> +
>> + if (data[0] & GOODIX_HAVE_KEY) {
>> + touch_num = data[0] & 0x0f;
>> + key_value = data[1 + ts->contact_size * touch_num];
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i)
>> + if (key_value & (1 << i))
>> + input_report_key(ts->input_dev, ts->keymap[i], 1);
>> + } else
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i)
>> + input_report_key(ts->input_dev, ts->keymap[i], 0);
>> +}
>> +
>> /**
>> * goodix_process_events - Process incoming events
>> *
>> @@ -363,7 +389,7 @@ static void goodix_ts_report_touch_9b(struct goodix_ts_data *ts, u8 *coor_data)
>> */
>> static void goodix_process_events(struct goodix_ts_data *ts)
>> {
>> - u8 point_data[1 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
>> + u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
>> int touch_num;
>> int i;
>> @@ -371,11 +397,7 @@ static void goodix_process_events(struct goodix_ts_data *ts)
>> if (touch_num < 0)
>> return;
>> - /*
>> - * Bit 4 of the first byte reports the status of the capacitive
>> - * Windows/Home button.
>> - */
>> - input_report_key(ts->input_dev, KEY_LEFTMETA, point_data[0] & BIT(4));
>> + goodix_ts_report_key(ts, point_data);
>> for (i = 0; i < touch_num; i++)
>> if (ts->contact_size == 9)
>> @@ -961,6 +983,7 @@ static int goodix_i2c_test(struct i2c_client *client)
>> static int goodix_configure_dev(struct goodix_ts_data *ts)
>> {
>> int error;
>> + int i;
>> ts->int_trigger_type = GOODIX_INT_TRIGGER;
>> ts->max_touch_num = GOODIX_MAX_CONTACTS;
>> @@ -978,8 +1001,19 @@ static int goodix_configure_dev(struct goodix_ts_data *ts)
>> ts->input_dev->id.product = ts->id;
>> ts->input_dev->id.version = ts->version;
>> + ts->input_dev->keycode = ts->keymap;
>> + ts->input_dev->keycodesize = sizeof(ts->keymap[0]);
>> + ts->input_dev->keycodemax = GOODIX_MAX_KEYS;
>> +
>> /* Capacitive Windows/Home button on some devices */
>> - input_set_capability(ts->input_dev, EV_KEY, KEY_LEFTMETA);
>> + for (i = 0; i < GOODIX_MAX_KEYS; ++i) {
>> + if (i == 0)
>> + ts->keymap[i] = KEY_LEFTMETA;
>> + else
>> + ts->keymap[i] = KEY_F1 + (i - 1);
>> +
>> + input_set_capability(ts->input_dev, EV_KEY, ts->keymap[i]);
>> + }
>> input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_X);
>> input_set_capability(ts->input_dev, EV_ABS, ABS_MT_POSITION_Y);
>>
>