@@ -1,41 +0,0 @@
-Atmel maXTouch touchscreen/touchpad
-
-Required properties:
-- compatible:
-    atmel,maxtouch
-
-    The following compatibles have been used in various products but are
-    deprecated:
-	atmel,qt602240_ts
-	atmel,atmel_mxt_ts
-	atmel,atmel_mxt_tp
-	atmel,mXT224
-
-- reg: The I2C address of the device
-
-- interrupts: The sink for the touchpad's IRQ output
-    See ../interrupt-controller/interrupts.txt
-
-Optional properties for main touchpad device:
-
-- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
-    on GPIO bit changes. An array of up to 8 entries can be provided
-    indicating the Linux keycode mapped to each bit of the status byte,
-    starting at the LSB. Linux keycodes are defined in
-    <dt-bindings/input/input.h>.
-
-    Note: the numbering of the GPIOs and the bit they start at varies between
-    maXTouch devices. You must either refer to the documentation, or
-    experiment to determine which bit corresponds to which input. Use
-    KEY_RESERVED for unused padding values.
-
-- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low)
-
-Example:
-
-	touch@4b {
-		compatible = "atmel,maxtouch";
-		reg = <0x4b>;
-		interrupt-parent = <&gpio>;
-		interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
-	};

@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/atmel,maxtouch.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Atmel maXTouch touchscreen/touchpad DT bindings
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  compatible:
+    enum:
+      - atmel,maxtouch
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  vdd-supply:
+    description: Phandle to regulator providing power to the touchscreen
+
+  linux,gpio-keymap:
+    minItems: 1
+    maxItems: 8
+    description: >
+      When enabled, the SPT_GPIOPWN_T19 object sends messages
+      on GPIO bit changes. An array of up to 8 entries can be provided
+      indicating the Linux keycode mapped to each bit of the status byte,
+      starting at the LSB. Linux keycodes are defined in
+      <dt-bindings/input/input.h>.
+
+      Note: the numbering of the GPIOs and the bit they start at varies between
+      maXTouch devices. You must either refer to the documentation, or
+      experiment to determine which bit corresponds to which input. Use
+      KEY_RESERVED for unused padding values.
+
+  reset-gpios:
+    description: GPIO specifier for the touchscreen's reset pin (active low)
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      mxt224-touchscreen@4a {
+        compatible = "atmel,maxtouch";
+        reg = <0x4a>;
+
+        interrupt-parent = <&gpx0>;
+        interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+
+        vdd-supply = <&tsp_reg>;
+      };
+    };