On Sun, Feb 17, 2019 at 02:45:52PM +0530, Jagan Teki wrote:

On Sun, Feb 17, 2019 at 1:21 PM Jagan Teki [off-list ref] wrote:

quoted

Hi Dmitry and Rob,

On Thu, Feb 14, 2019 at 3:21 AM Rob Herring [off-list ref] wrote:

quoted

On Tue, Jan 22, 2019 at 7:39 AM Jagan Teki [off-list ref] wrote:

quoted

On Mon, Jan 21, 2019 at 9:46 PM Rob Herring [off-list ref] wrote:

quoted

On Fri, Jan 18, 2019 at 10:01 AM Jagan Teki [off-list ref] wrote:

quoted

On Wed, Jan 9, 2019 at 7:08 PM Rob Herring [off-list ref] wrote:

quoted

Please CC DT list if you want bindings reviewed.

Sorry I forgot.

quoted

On Wed, Jan 9, 2019 at 1:40 AM Dmitry Torokhov
[off-list ref] wrote:

quoted

On Sat, Dec 15, 2018 at 08:47:59PM +0530, Jagan Teki wrote:

quoted

Most of the Goodix CTP controllers are supply with AVDD28 pin.
which need to supply for controllers like GT5663 on some boards
to trigger the power.

So, document the supply property so-that the require boards
that used on GT5663 can enable it via device tree.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 Documentation/devicetree/bindings/input/touchscreen/goodix.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index f7e95c52f3c7..c4622c983e08 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt

@@ -23,6 +23,7 @@ Optional properties:
  - touchscreen-inverted-y  : Y axis is inverted (boolean)
  - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
                              (swapping is done after inverting the axis)
+ - AVDD28-supply     : Analog power supply regulator on AVDD28 pin

I think we normally use lower case in DT bindings and rarely encode
voltage in the supply name unless we are dealing with several supplies
of the same kind, but I'll let Ron comment on this.

Yes on lowercase though there are some exceptions.

There's also a AVDD22 supply as well as DVDD12 and VDDIO. So we
probably need to keep the voltage, but the binding is incomplete.

What is incomplete here? can you please elaborate.

You are missing the 3 other supplies the chip has: AVDD22, DVDD12 and VDDIO.

Though it has other supplies, only AVDD28 is connected in the Host
interface design similar like 9. Reference Schematic on Page, 23 in
attached manual.

That is for a particular board design. It still has other supplies.
Just make the binding complete please. You can make them optional. I
don't care if the driver supports controlling all the supplies or not
(though Dmitry might).

So, Can I make bulk get and enable in all 4 regulators global to
driver or specific to that chip, in either way the regulators which
are not used to process via dummy regulators (which we all know).

or regulator which are not using are get via devm_regulator_get_optional.

Any suggestions?

Just realized to go with bulk calls, please have a look at on v5 [1]

I do not believe you can use bulk regulator API here as you need to
implement the power up timing scheme mentioned on p. 12 of the spec you
referenced earlier. And, because of that timing diagram, I believe if
you want to control AVDD supply, you also have to control VDDIO supply
as it has to be on only after enabling AVDD.

I also wonder if it is valid to have both AVDD28 and AVDD22 connected at
the same time.

Thanks.

-- 
Dmitry