[PATCH v2 2/3] i2c: qup: Introduce SCL/SDA noise rejection
From: AngeloGioacchino Del Regno <hidden>
Date: 2021-01-14 17:50:10
Also in:
linux-arm-msm, linux-devicetree, lkml, phone-devel
Subsystem:
arm/qualcomm mailing list, i2c subsystem, i2c subsystem host drivers, the rest · Maintainers:
Wolfram Sang, Andi Shyti, Linus Torvalds
Some I2C devices may be glitchy due to electrical noise coming from the device itself or because of possible board design issues. To overcome this issue, the QUP's I2C in Qualcomm SoCs supports a noise rejection setting for both SCL and SDA lines. Introduce a setting for noise rejection through device properties, "qcom,noise-reject-sda" and "qcom,noise-reject-scl", which will be used to set the level of noise rejection sensitivity. If the properties are not specified, noise rejection will not be enabled. Signed-off-by: AngeloGioacchino Del Regno <redacted> --- drivers/i2c/busses/i2c-qup.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
index 5a47915869ae..af51234a60ba 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c@@ -8,6 +8,7 @@ #include <linux/acpi.h> #include <linux/atomic.h> #include <linux/clk.h> +#include <linux/bitfield.h> #include <linux/delay.h> #include <linux/dmaengine.h> #include <linux/dmapool.h>
@@ -39,6 +40,8 @@ #define QUP_MX_READ_CNT 0x208 #define QUP_IN_FIFO_BASE 0x218 #define QUP_I2C_CLK_CTL 0x400 +#define QUP_I2C_CLK_CTL_SDA_NR GENMASK(27, 26) +#define QUP_I2C_CLK_CTL_SCL_NR GENMASK(25, 24) #define QUP_I2C_STATUS 0x404 #define QUP_I2C_MASTER_GEN 0x408
@@ -1663,6 +1666,7 @@ static int qup_i2c_probe(struct platform_device *pdev) int ret, fs_div, hs_div; u32 src_clk_freq = DEFAULT_SRC_CLK; u32 clk_freq = DEFAULT_CLK_FREQ; + u32 noise_reject_scl = 0, noise_reject_sda = 0; int blocks; bool is_qup_v1;
@@ -1860,6 +1864,19 @@ static int qup_i2c_probe(struct platform_device *pdev) qup->clk_ctl = ((fs_div / 2) << 16) | (hs_div << 8) | (fs_div & 0xff); } + /* SCL/SDA Noise rejection (optional) */ + ret = device_property_read_u32(qup->dev, "qcom,noise-reject-scl", + &noise_reject_scl); + if (ret == 0) + qup->clk_ctl |= FIELD_PREP(QUP_I2C_CLK_CTL_SCL_NR, + noise_reject_scl); + + ret = device_property_read_u32(qup->dev, "qcom,noise-reject-sda", + &noise_reject_sda); + if (ret == 0) + qup->clk_ctl |= FIELD_PREP(QUP_I2C_CLK_CTL_SDA_NR, + noise_reject_sda); + /* * Time it takes for a byte to be clocked out on the bus. * Each byte takes 9 clock cycles (8 bits + 1 ack).
--
2.29.2