On Sun, 13 Dec 2020 05:50:33 PST (-0800), Damien Le Moal wrote:

This series of patches improves support for boards based on the Canaan
Kendryte K210 RISC-V dual core SoC. Minimal support for this SoC is
already included in the kernel. These patches complete it, enabling
support for most peripherals present on the SoC as well as introducing
device trees for the various K210 boards available on the market today
from SiPeed and Kendryte.

Putting everything together like this makes it overly difficult to get things
merged: there's some actual fixes, some new arch/riscv stuff, and a handful of
drivers.  I know we've been kind of mixing up the SiFive and RISC-V trees, but
that's largely because things have been pretty quiet and it's the same people
working on everything.  That'll probably change at some point, but it doesn't
mean we can just start mixing up everything in here -- even for the SiFive
stuff, we usulaly try to do it in the relevant subsystem tree.

Pathes 1 to 4 are various fixes for riscv arch code and riscv
dependent devices. Of note here is patch 3 which fix system calls
execution in the no MMU case, and patch 4 which simplifies DTB builtin
handling.

The first three are on fixes, but the fourth isn't a fix: it's a fairly
significant change to how portable our kernels can be.  The old scheme allows
vendors the option of building systems with M-mode compatibility, this new one
doesn't.  That said, I don't think anyone is actually going to build systems
this way -- we really should have had some sort of mboardid, but that was shot
down in favor of some sort of platform thing and it's unlikely we get that far
over there.

I'm not really sure I'm ready to throw in the towel on binary compatibility
between vendors yet, at least in general.  In this specific case it seems fine,
though -- accross the board we're just spending way too much time worrying
about the small things while we have way bigger problems to deal with.
Obviously it would be better if we had some scheme to handle this here, but I'd
much rather focus on the basics.

I still hope we get to the point where we can have binary compatibility between
systems from various vendors, while still having reasonably useful systems.
Unfortunately we're quite far away from anything like that, so I'm fine taking
this sort of thing as that's as good as we can do for the forseeable future.

This is on for-next.

Patch 5 fixes naming of directories and configuration options to use the
K210 SoC vendor name (Canaan) instead of its branding name (Kendryte).

Patch 6 is a preparatory patch cleaning up the K210 system controller
driver to facilitate introducing the SoC clock driver.

These are also on for-next.

The following patches 7 to 11 document device tree bindings for the SoC
drivers. The implementation of these drivers is provided in patches 12,
13 and 14, respectively implementing the SoC clock driver, reset
controller and SOC pin function control.

The numbering is off a bit here.  The clock stuff has gone in through that tree
and I'm fine  taking the reset controller as that's been reviewed, but I don't
see any review on the pinctl driver so I haven't taken that yet.

I'm happy to re-send that patch (likely with a more appropriate subject line,
as it's a pinctl driver not a riscv patch).

Patches 15 to 20 update the existing K210 device tree and add new
device tree files for several K210 based boards: MAIX Bit, MAIXDUINO,
MAIX Dock and MAIX Go boards from SiPeed and the KD233 development
board from Canaan.

There are tons of checkpatch warnings in these, mostly related to compat
strings that don't have binding definitions.  It looks like there's just a lot
of stuff in there that doesn't have any support on the Linux side, my guess
would be that the best thing to do is to drop those until they're defined.

Finally the last two patches updates the k210 nommu defconfig to include
the newly implemented drivers and provide a new default configuration
file enabling SD card support.

I'm also going to just leave these out for now, until we sort out the above
issues.  Let me know if you're going to send another patch set, or 

A lot of the work on the device tree and on the K210 drivers come from
the work by Sean Anderson for the U-Boot project support of the K210
SoC. Sean also helped with debugging many aspects of this series.

A tree with all patches applied is available here:
https://github.com/damien-lemoal/linux, k210-sysctl-v22 branch.
A demonstration of this series used on a SiPeed MAIX Dock
board together with an I2C servo controller can be seen here:
https://damien-lemoal.github.io/linux-robot-arm/#example

This tree was used to build userspace busybox environment image that is
then copied onto an SD card formatted with ext2:
https://github.com/damien-lemoal/buildroot
Of note is that running this userspace environment requires a revert of
commit 2217b982624680d19a80ebb4600d05c8586c4f96 introduced during the
5.9 development cycle. Without this revert, execution of the init
process fails. A problem with the riscv port of elf2flt is suspected but
not confirmed. I am now starting to investigate this problem.

Reviews and comments are as always much welcome.

Changes from v9:
* Added patch 6 to avoid DTS compilation errors after patch 9 is
  applied and until patch 16 is applied.

Changes from v8:
* Addressed Rob's comments on the sysctl driver bindings documentation
* Fixed a typo in the fpios driver bindings documentation

Changes from v7:
* Removed the __init annotation for the drivers reset, pinctrl and
  sysctl drivers probe functions as suggested by Geert. Also removed
  the __refdata annotation for the struct platform_driver variables of
  these drivers.

Changes from v6:
* Annotate struct platform_driver variables with __refdata to avoid
  section mismatch compilation errors
* Add empty sentinel entry to of_device_id tables of the sysctl, reset
  and pinctrl drivers.

Changes from v5:
* Addressed Philipp's comment on the reset controller driver
* Added patch 6 to reduce the size of the clock driver patch
  (now patch 12).

Changes from v4:
* Simplified reset controller driver using of_xlate callback as
  suggested by Philipp
* Fixed compilation error when using other configs than one of the
  nommu_k210 defconfigs.
* Addressed most clock driver comments from Stephen.
* Removed CONFIG_GPIO_SYSFS from defconfigs
* Rebased on 5.10-rc7

Changes from V3:
* Add one entry per driver in MAINTAINERS file

Changes from V2:
* Add MAINTAINERS file entry for the SoC support, listing myself as
  maintainer.
* Removed use of postcore_initcall() for declaring the drivers, using
  the regular builtin_platform_driver() instead.
* Fixed fpio pinctrl driver bindings documentation as commented by
  Geert: removed input-schmitt and added input-schmitt-disable, fixed
  typo and added input-disable and output-disable.
* Fixed device tree to have cs-gpios active low, as per the default, as
  active high necessity was an artifact of the gpio level double
  inversion bug fixed recently.
* Removed CONFIG_VT from defconfigs to reduce the kernel image size as
  suggested by Geert.

Changes from v1:
* Improved DT bindings documentation
* SPI and GPIO patches removed from this series (and being processed
  directly through the relevant subsystems directly)
* Improved device trees
* Various cleanup and improvments of the drivers

Damien Le Moal (22):
  riscv: Fix kernel time_init()
  riscv: Fix sifive serial driver
  riscv: Enable interrupts during syscalls with M-Mode
  riscv: Fix builtin DTB handling
  riscv: Use vendor name for K210 SoC support
  riscv: cleanup Canaan Kendryte K210 sysctl driver
  dt-bindings: Add Canaan vendor prefix
  dt-binding: clock: Document canaan,k210-clk bindings
  dt-bindings: reset: Document canaan,k210-rst bindings
  dt-bindings: pinctrl: Document canaan,k210-fpioa bindings
  dt-binding: mfd: Document canaan,k210-sysctl bindings
  riscv: Add Canaan Kendryte K210 clock driver
  riscv: Add Canaan Kendryte K210 reset controller
  riscv: Add Canaan Kendryte K210 FPIOA driver
  riscv: Update Canaan Kendryte K210 device tree
  riscv: Add SiPeed MAIX BiT board device tree
  riscv: Add SiPeed MAIX DOCK board device tree
  riscv: Add SiPeed MAIX GO board device tree
  riscv: Add SiPeed MAIXDUINO board device tree
  riscv: Add Kendryte KD233 board device tree
  riscv: Update Canaan Kendryte K210 defconfig
  riscv: Add Canaan Kendryte K210 SD card defconfig

Damien Le Moal (23):
  riscv: Fix kernel time_init()
  riscv: Fix sifive serial driver
  riscv: Enable interrupts during syscalls with M-Mode
  riscv: Fix builtin DTB handling
  riscv: Use vendor name for K210 SoC support
  riscv: Fix Canaan Kendryte K210 device tree
  riscv: cleanup Canaan Kendryte K210 sysctl driver
  dt-bindings: Add Canaan vendor prefix
  dt-binding: clock: Document canaan,k210-clk bindings
  dt-bindings: reset: Document canaan,k210-rst bindings
  dt-bindings: pinctrl: Document canaan,k210-fpioa bindings
  dt-binding: mfd: Document canaan,k210-sysctl bindings
  riscv: Add Canaan Kendryte K210 clock driver
  riscv: Add Canaan Kendryte K210 reset controller
  riscv: Add Canaan Kendryte K210 FPIOA driver
  riscv: Update Canaan Kendryte K210 device tree
  riscv: Add SiPeed MAIX BiT board device tree
  riscv: Add SiPeed MAIX DOCK board device tree
  riscv: Add SiPeed MAIX GO board device tree
  riscv: Add SiPeed MAIXDUINO board device tree
  riscv: Add Kendryte KD233 board device tree
  riscv: Update Canaan Kendryte K210 defconfig
  riscv: Add Canaan Kendryte K210 SD card defconfig

 .../bindings/clock/canaan,k210-clk.yaml       |   54 +
 .../bindings/mfd/canaan,k210-sysctl.yaml      |  109 ++
 .../bindings/pinctrl/canaan,k210-fpioa.yaml   |  171 +++
 .../bindings/reset/canaan,k210-rst.yaml       |   40 +
 .../devicetree/bindings/vendor-prefixes.yaml  |    2 +
 MAINTAINERS                                   |   23 +
 arch/riscv/Kconfig.socs                       |   33 +-
 arch/riscv/Makefile                           |    2 +-
 arch/riscv/boot/dts/Makefile                  |    2 +-
 arch/riscv/boot/dts/canaan/Makefile           |    5 +
 arch/riscv/boot/dts/canaan/k210.dtsi          |  621 ++++++++++
 arch/riscv/boot/dts/canaan/k210_generic.dts   |   46 +
 arch/riscv/boot/dts/canaan/k210_kd233.dts     |  178 +++
 arch/riscv/boot/dts/canaan/k210_maix_bit.dts  |  227 ++++
 arch/riscv/boot/dts/canaan/k210_maix_dock.dts |  229 ++++
 arch/riscv/boot/dts/canaan/k210_maix_go.dts   |  237 ++++
 arch/riscv/boot/dts/canaan/k210_maixduino.dts |  201 ++++
 arch/riscv/boot/dts/kendryte/Makefile         |    4 -
 arch/riscv/boot/dts/kendryte/k210.dts         |   23 -
 arch/riscv/boot/dts/kendryte/k210.dtsi        |  125 --
 arch/riscv/configs/nommu_k210_defconfig       |   39 +-
 .../riscv/configs/nommu_k210_sdcard_defconfig |   93 ++
 arch/riscv/include/asm/soc.h                  |   38 -
 arch/riscv/kernel/entry.S                     |    9 +
 arch/riscv/kernel/soc.c                       |   27 -
 arch/riscv/kernel/time.c                      |    3 +
 arch/riscv/mm/init.c                          |    6 +-
 drivers/clk/Kconfig                           |    8 +
 drivers/clk/Makefile                          |    1 +
 drivers/clk/clk-k210.c                        | 1005 +++++++++++++++++
 drivers/pinctrl/Kconfig                       |   13 +
 drivers/pinctrl/Makefile                      |    1 +
 drivers/pinctrl/pinctrl-k210.c                |  985 ++++++++++++++++
 drivers/reset/Kconfig                         |   10 +
 drivers/reset/Makefile                        |    1 +
 drivers/reset/reset-k210.c                    |  131 +++
 drivers/soc/Kconfig                           |    2 +-
 drivers/soc/Makefile                          |    2 +-
 drivers/soc/canaan/Kconfig                    |   12 +
 drivers/soc/canaan/Makefile                   |    3 +
 drivers/soc/canaan/k210-sysctl.c              |   78 ++
 drivers/soc/kendryte/Kconfig                  |   14 -
 drivers/soc/kendryte/Makefile                 |    3 -
 drivers/soc/kendryte/k210-sysctl.c            |  260 -----
 drivers/tty/serial/sifive.c                   |    1 +
 include/dt-bindings/clock/k210-clk.h          |   55 +-
 include/dt-bindings/pinctrl/k210-fpioa.h      |  276 +++++
 include/dt-bindings/reset/k210-rst.h          |   42 +
 include/soc/canaan/k210-sysctl.h              |   43 +
 49 files changed, 4962 insertions(+), 531 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml
 create mode 100644 Documentation/devicetree/bindings/mfd/canaan,k210-sysctl.yaml
 create mode 100644 Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml
 create mode 100644 Documentation/devicetree/bindings/reset/canaan,k210-rst.yaml
 create mode 100644 arch/riscv/boot/dts/canaan/Makefile
 create mode 100644 arch/riscv/boot/dts/canaan/k210.dtsi
 create mode 100644 arch/riscv/boot/dts/canaan/k210_generic.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_kd233.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_maix_bit.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_maix_dock.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_maix_go.dts
 create mode 100644 arch/riscv/boot/dts/canaan/k210_maixduino.dts
 delete mode 100644 arch/riscv/boot/dts/kendryte/Makefile
 delete mode 100644 arch/riscv/boot/dts/kendryte/k210.dts
 delete mode 100644 arch/riscv/boot/dts/kendryte/k210.dtsi
 create mode 100644 arch/riscv/configs/nommu_k210_sdcard_defconfig
 create mode 100644 drivers/clk/clk-k210.c
 create mode 100644 drivers/pinctrl/pinctrl-k210.c
 create mode 100644 drivers/reset/reset-k210.c
 create mode 100644 drivers/soc/canaan/Kconfig
 create mode 100644 drivers/soc/canaan/Makefile
 create mode 100644 drivers/soc/canaan/k210-sysctl.c
 delete mode 100644 drivers/soc/kendryte/Kconfig
 delete mode 100644 drivers/soc/kendryte/Makefile
 delete mode 100644 drivers/soc/kendryte/k210-sysctl.c
 create mode 100644 include/dt-bindings/pinctrl/k210-fpioa.h
 create mode 100644 include/dt-bindings/reset/k210-rst.h
 create mode 100644 include/soc/canaan/k210-sysctl.h