[PATCH v2 8/8] arm64: dts: qcom: sm8150-hdk: add display card overlay

From
Dmitry Baryshkov <hidden>
Date
2026-10-19 11:26:09
Also in
dri-devel, linux-arm-msm, linux-devicetree, lkml
Reply to
Dmitry Baryshkov, 2026-10-19
The SM8150 HDK can be fitted with a display card carrying a Truly
NT36850 WQHD dual-DSI panel. It uses the PM8150L WLED for the backlight
and LCDB for the bias rails, and it is mutually exclusive with the
on-board LT9611 HDMI bridge.

Only two of the three WLED strings are connected on the card: the
backlight stays dark and the boost runs into the overvoltage limit if
only the third string is driven.

Assisted-by: LLM
Signed-off-by: Dmitry Baryshkov <redacted>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   4 +
 .../boot/dts/qcom/sm8150-hdk-display-card.dtso     | 113 +++++++++++++++++++++
 2 files changed, 117 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 85d06a950b4a..571bda210d63 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -409,6 +409,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm7325-nothing-spacewar.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm7325-xiaomi-lisa.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm7325-xiaomi-taoyao.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
+
+sm8150-hdk-display-card-dtbs	:= sm8150-hdk.dtb sm8150-hdk-display-card.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk-display-card.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-sony-xperia-kumano-bahamut.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk-display-card.dtso b/arch/arm64/boot/dts/qcom/sm8150-hdk-display-card.dtso
new file mode 100644
index 000000000000..bd57459f9c86
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk-display-card.dtso
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/*
+ * Display Card kit overlay.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/plugin/;
+
+/* Disable HDMI bridge related nodes (mutually exclusive with the display card) */
+&lt9611_codec {
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "truly,wqhd60-nt36850";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		vddio-supply = <&vreg_l14a_1p8>;
+		avdd-supply = <&pm8150l_lcdb_ldo>;
+		avee-supply = <&pm8150l_lcdb_ncp>;
+
+		backlight = <&pm8150l_wled>;
+
+		pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync>;
+		pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync>;
+		pinctrl-names = "default", "sleep";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				panel0_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				panel1_in: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+};
+
+&mdss_dsi1_out {
+	remote-endpoint = <&panel1_in>;
+};
+
+&pm8150l_lcdb {
+	status = "okay";
+};
+
+&pm8150l_lcdb_ldo {
+	regulator-min-microvolt = <5500000>;
+	regulator-max-microvolt = <5500000>;
+};
+
+&pm8150l_lcdb_ncp {
+	regulator-min-microvolt = <5500000>;
+	regulator-max-microvolt = <5500000>;
+};
+
+&pm8150l_wled {
+	qcom,num-strings = <2>;
+
+	status = "okay";
+};
+
+&tlmm {
+	disp0_reset_n_active: disp0-reset-n-active-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	disp0_reset_n_suspend: disp0-reset-n-suspend-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdp_vsync: mdp-vsync-state {
+		pins = "gpio8";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
-- 
2.47.3
Thread (19 messages) 19 messages, 5 authors, last reply 12d ago
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help